CHAUVET Professional ML5 Rogue Outcast 1 Beam Wash User Guide
- June 2, 2024
- Chauvet Professional
Table of Contents
CHAUVET Professional ML5 Rogue Outcast 1 Beam Wash
Specifications
- Model ID: ROGUEOUTCAST1BEAMWASH
- Power Linking: Up to 3 products at 100V or 120V, 6 products at 208V, or up to 7 products at 230V or 240V
- Mounting: Requires at least two mounting points per product
- Control Panel: Includes navigation buttons for menu selection and value adjustment
Safety Notes
Read and follow the safety notes provided in the manual for proper
installation, use, and maintenance of the Rogue Outcast 1 Beam Wash.
Power Linking
Ensure not to exceed the specified number of products that can be power linked
based on the voltage. Use power-linking cables for connecting multiple units.
AC Power Connection
Follow the provided color-coding for AC power connection based on the
region. Ensure proper grounding for safe operation.
Mounting Instructions
Before mounting, review the Safety Notes. Use suitable mounting clamps
capable of supporting the product’s weight. Refer to Chauvet’s line of
mounting clamps for compatibility.
Control Panel Usage
Understand the button functions on the control panel for navigating menus,
selecting options, and adjusting values.
FAQ
- What is the maximum number of products that can be power linked?
The Rogue Outcast 1 Beam Wash allows power linking of up to 3 products at 100V or 120V, 6 products at 208V, and up to 7 products at 230V or 240V.
Scan the QR code to access the product page, warranty terms, and the complete User Manual
Quick Reference Guide
Safety Notes
These Safety Notes include important information about installation, use, and
maintenance of the Rogue Outcast 1 Beam Wash.
- The luminaire is intended for professional use only.
- The luminaire should be positioned so that prolonged staring into the luminaire at a distance closer than 18.4 ft (5.5 m) is not expected.
- If the external flexible cable or cord of this luminaire is damaged, it shall be replaced by a special cord or cord exclusively available from the manufacturer or its service agent.
- The light source contained in this luminaire shall only be replaced by the manufacturer or its service agent or a similar qualified person.
- CAUTION:
- This product’s housing may be hot when operating. Mount this product in a location with adequate ventilation, at least 20 in (50 cm) from adjacent surfaces.
- When transferring the product from extreme temperature environments, (e.g., cold truck to warm humid ballroom) condensation may form on the internal electronics of the product. To avoid causing a failure, allow the product to fully acclimate to the surrounding environment before connecting it to power.
- Flashing light is known to trigger epileptic seizures. User must comply with local laws regarding notification of strobe use.
- ALWAYS:
- Disconnect from power before cleaning the product or replacing the fuse.
- Replace the fuse with the same type and rating.
- Use a safety cable when mounting this product overhead.
- Connect this product to a grounded and protected circuit.
- DO NOT:
- Open this product. It contains no user-serviceable parts.
- Look at the light source when the product is on.
- Leave any flammable material within 50 cm of this product while operating or connected to power.
- Connect this product to a dimmer or rheostat.
- Operate this product if the housing, lenses, or cables appear damaged.
- Submerge this product (IP65). Regular outdoor operation is fine.
- Permanently install outdoors in locations with extreme environmental conditions. This includes, but is not limited to:
- Exposure to a marine/saline environment (within 3 miles of a saltwater body of water).
- Locations where normal temperatures exceed the temperature ranges in this manual.
- Locations that are prone to flooding or being buried in snow.
- Other areas where the product will be subject to extreme radiation or caustic substances.
- ONLY use the hanging/mounting bracket to carry this product.
- The maximum ambient temperature is 113 °F (45 °C). Do not operate this product at higher temperatures.
- The minimum ambient temperature is -4°F (-20°C). Do not operate the product at lower temperatures.
- In the event of a serious operating problem, stop using immediately.
FCC Compliance
This device complies with Part 15 Part B of the FCC rules. Operation is
subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
RF Exposure Warning for North America and Australia
Warning! This equipment complies with FCC radiation exposure limits set forth
for an uncontrolled environment. This equipment should be installed and
operated with a minimum distance of 20 cm between the radiator and your body.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
What is Included
- Rogue Outcast 1 Beam Wash
- Seetronic Powerkon IP65 power cable
- 2 omega brackets with mounting hardware
- Quick Reference Guide
AC Power
This product has an auto-ranging power supply that can work with an input
voltage range of 100–240 VAC, 50/60 Hz.
AC Plug
| Connection | Wire (U.S.) | Wire (Europe) | Screw Color |
|---|---|---|---|
| AC Live | Black | Brown | Yellow/Brass |
| AC Neutral | White | Blue | Silver |
| AC Ground | Green/Yellow | Green/Yellow | Green |
Power Linking
It is possible to power link up to 3 Rogue Outcast 1 Beam Wash products at 100
V or 120 V, 6 products at 208 V, or up to 7 products at 230 V or 240 V. Never
exceed this number. Power-linking cables can be purchased separately.
To eliminate unnecessary wear and improve its lifespan, during periods of non- use completely disconnect the product from power via breaker or by unplugging it.
Mounting
Before mounting this product, read the Safety Notes. Use at least two mounting
points per product. Make sure the mounting clamps are capable of supporting
the weight of the product. For our Chauvet line of mounting clamps, go to
http://trusst.com/productcategory/truss-clamps/
Control Panel Description
| Button | Function |
|---|---|
| < MENU> | Exits from the current menu or function |
| < ENTER> | Enables the currently displayed menu or sets the currently |
selected value into the selected function
< UP>| Navigates upwards through the menu list or increases the numeric
value when in a function
< DOWN>| Navigates downwards through the menu list or decreases the
numeric value when in a function
Contact Us
- Email: [email protected]
- Website: www.chauvetprofessional.com
- Email: [email protected]
- Website: www.chauvetprofessional.eu
- Email: [email protected]
- Website: www.chauvetprofessional.eu
- Email: [email protected]
- Website: www.chauvetprofessional.eu
- Email: [email protected]
- Website: www.chauvetprofessional.eu
- Email: [email protected]
- Website: www.chauvetprofessional.eu
- Email: [email protected]
- Website: www.chauvetprofessional.mx
Visit the applicable website above to verify our contact information and instructions to request support. Outside the U.S., U. K., Ireland, Mexico, France, Germany, or Benelux, contact the dealer of record.
