ZALMAN K1 ATX Mid Tower Computer Case User Manual

June 4, 2024
ZALMAN

ZALMAN K1 ATX Mid Tower Computer Case

ZALMAN-K1-ATX-Mid-Tower-Computer-image

To ensure safe and easy installation, please read the following precautions.
Product design and specifications may be revised to improve quality and performance without notice.

Developed and designed by ZALMAN in Korea.
This product is protected by ZALMAN’s pending or registered patents.

www.zalman.com

Precautions

  • Read this manual carefully before installing.
  • Check the product and components before installing. If you find any abnormality, contact the location where you purchased the product for a replacement or refund.
  • Wear gloves to prevent accidents when installing the product.
  • Severe damage may occur when mounting the system, so do not apply excessive force.
  • Connecting the cable incorrectly may cause a fire due to a short circuit. Make sure to refer to the manual when connecting the cable.
  • Be careful not to block the ventilation hole of the product when using the system.
  • Avoid locations with direct sunlight, water, moisture, oil, and excessive dust. Store and use the product in a well-ventilated location.
  • Do not wipe the surface of the product using chemicals. (organic solvents such as alcohol or acetone)
  • Do not insert your hand or other object into the product during operation, as this may injure your hand or damage the object.
  • Store and use the product out of children’s reach.
  • Our company assumes no responsibility for any problem that occurs due to the use of the product for purposes other than its designated purposes and/or the carelessness of the consumer.
  • The exterior design and specifications of the product are subject to change without prior notice to consumers for quality improvement.

Specifications

Model K1 Rev.B
Case Form Factor ATX Mid-Tower
Dimensions 470 x 220 x 470(H)mm
Weight 6.4kg
Case Materials Plastic, Steel, Tempered Glass
Motherboard Support ATX I mATX / Mini-lTX
Maximum VGA Length 380mm
Maximum CPU Cooler Height 178mm
Maxi mum PSU Length 190mm
PCI Expansion Slots
Drive Bays  

Fan Support

| 2 x 120mm / 2 x 140mm

3 x 120mm / 2 x 140mm

1 x 120mm / 1 x 140mm __

2 x 120mm

1 x 120mm , 1 x Addressable RGB L ED Bar __

1 x 120mm (ARGB Fan ZM-RFD120A) __

essable RGB Controller Included

120mm _ _I__ 240mm

120mm / 240mm / 280mm _ _I 360mm

Rear         120mm

Fan(s) Included

Radiator Support

1/0 Ports                                          1 x Headphone , 1 x Mic, 2 x USS 2.0, 2 x USB 3.0,

1 x LED Contro l Bu tton, Power Button, Reset Button

ZALMAN-K1-ATX-Mid-Tower-Computer-fig2

Accessories component

ZALMAN-K1-ATX-Mid-Tower-Computer-fig3

1/0 Ports

ZALMAN-K1-ATX-Mid-Tower-Computer-fig4 ZALMAN-K1
-ATX-Mid-Tower-Computer-fig22 ZALMAN-K1-ATX-Mid-Tower-Computer-fig5

Caution: Please do not connect ARGB fans more than Bpcs, otherwise it may cause malfunction

How to control RGB LED

  • LED Colors & patterns can be changed by pressing the LED Button on /O ports.
  • Long pressing on the LED Button for 6 seconds, RGB LED will be turn off after blinking twice in white.
  • Long pressing on the LED Button for 3 seconds, RGB will be synchronized with the motherboard after blinking once in white.
  • Press the LED BUtton again to desynchronize with the motherboard.

A ARGB LED 1-4 /3-Pin
B ARGB LED Control Button /2-Pin

  • Connector to ARGB LED Control Button

C Other Motherboards Sync/ 3-Pin

  • Connector to Motherboard
  • Requires Motherboard that Supports RGB Sync

Caution: if Addressable 3 Pin connects to 12V header instead of 5V header improperly, It may cause fatal damages to the product by the overvoltage.

D SATA Power/ 15-Pin

  • Connector to PSU
  • Input: 5V

E Connect the ARGB connector to the RGB hub

  1. Removing the side panelsZALMAN-K1-ATX-Mid-Tower-Computer-fig9

  2. Removing the front panel

  3. Mounting the motherboardZALMAN-K1-ATX-Mid-Tower-Computer-fig11

  4. Motherboard sizeZALMAN-K1-ATX-Mid-Tower-Computer-fig12

  5. Mounting the PSUZALMAN-K1-ATX-Mid-Tower-Computer-fig13

  6. Mounting PCI-E(VGA) cardZALMAN-K1-ATX-Mid-Tower-Computer-fig14

  7. Mounting the 3.5″ and 2.5″ SSD / HDDZALMAN-K1-ATX-Mid-Tower-Computer-fig15

  8. Mounting the 2.5″ SSDZALMAN-K1-ATX-Mid-Tower-Computer-fig16

  9. Mounting guide the fansZALMAN-K1-ATX-Mid-Tower-Computer-fig17

  10. Mounting the radiator

  11. Mounting the front radiator
    120mm/ 240mm/ 280mm / 360mmZALMAN-K1-ATX-Mid-Tower-Computer-
fig18

  12. Mounting the top radiator
    120mm/240mm

  13. Mounting the rear radiator
    120mm

  14. L/O ConnectorsZALMAN-K1-ATX-Mid-Tower-Computer-fig21

Certification

CE
RoHS
This mark, designed by Zalman, indicates product Compliance with the European Union’s RoHS (Restriction of Hazardous Substances) Directive.

Disposal of Old Electrical & Electronic Equipment Applicable in the European Union and other European countries with separate collection systems)

www.zalman.com

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals