thermaltake Toughpower GF1 Power Supply Instruction Manual
- June 5, 2024
- thermaltake
Table of Contents
thermaltake Toughpower GF1 Power Supply
Warnings and Caution
- Do not unplug the AC power cord when the power supply is in Doing so may cause damage to your components.
- Do not place the power supply in a high humidity and/or temperature
- High voltages exist in the power Do not open the power supply case unless you are an authorized service technician or electrician. Doing so will void the warranty.
- The power supply should be powered by the source indicated on the rating
- Please use only genuine Thermaltake modular cables with Thermaltake Cable Management power supply models.Third party cables might not be compatible and could cause serious damage to your system and power The warranty is voided with the use of third-party cables.
- All warranties and guarantees will be voided, if failure to comply with any of the warnings and cautions covered in this
Components Check
- AC power cord
- TOUGHPOWER GF1 power supply unit – User manual
- Mounting screws x 4
- ARGB Sync cable x 1
Power Connector Introduction
CABLE
Wattage
| | | | | |
---|---|---|---|---|---|---
Main Power Connector (24 Pin)| ATX 12 V
Connector
(8 Pin/4+4 Pin)
| SATA
Connector
(5 Pin)
| PCI-E
Connector
(6+2 Pin)
| Peripheral Connector
(4 Pin)
| Floppy Adapter (4 Pin)
850W| 1| 2| 12| 6| 4| 1
750W| 1| 2| 9| 4| 4| 1
650W| 1| 2| 9| 4| 4| 1
Specification
Wattage| AC INPUT| Input Voltage: 100V – 240V~ ;
Input Current: 12A max ; Frequency: 47Hz – 63Hz
---|---|---
850W
| DC OUTPUT| +3.3V| +5V| +12V| -12V| +5VSB
Max Output Current| 22A| 22A| 70.9A| 0.3A| 3A
Max Output Power| 120W| 850.8W| 3.6W| 15W
Wattage| AC INPUT| Input Voltage: 100V – 240V~ ;
Input Current: 10A max ; Frequency: 47Hz – 63Hz
750W
| DC OUTPUT| +3.3V| +5V| +12V| -12V| +5VSB
Max Output Current| 22A| 22A| 62.5A| 0.3A| 3A
Max Output Power| 120W| 750W| 3.6W| 15W
Wattage| AC INPUT| Input Voltage: 100V – 240V~ ;
Input Current: 10A max ; Frequency: 47Hz – 63Hz
650W
| DC OUTPUT| +3.3V| +5V| +12V| -12V| +5VSB
Max Output Current| 22A| 22A| 54.2A| 0.3A| 3A
Max Output Power| 120W| 650.4W| 3.6W| 15W
Installation Steps
- Open your computer chassis; please refer to the instruction manual provided with your chassis.
- Install the PsU into the case with the four screS provided.
- If your motherboard requires a 24pin Main Power connector, please connect the 24pin Main Power connector to the motherboard.
- 1 For a motherboard that only requires a 4pin ATX 12V (CPU) connector, please detach a 4pin connector from the 4+4pin ATX 12V connector and connect it to the motherboard. (Either one of the 4pin from the 4+4pin ATX 12V connector will work)
- For motherboard that requires a single 8pin EPS connector, please use the 4+4pin connector from the power supply.
- Connect the SATA devices (if applicable) to the power supply using the SATA cables provided, i.e. hard drives, CD/DVD drives
- Connect any devices that may use the 4 pin peripheral connectors, i.e. hard drives, CD/DVD drives or case fans.
- If your graphic card requires PCI-E power connector, please connect corresponding PCI-E connector instructed by your graphic card’s user manual. Please note the power supply utilizes an unique 6+2pin PCI-E connector that can be effectively used as a single 8pin or 6pin PCI-E connector. To use it as a 6pin PCI-E connector, please detach the 2pin connector from the 6+2pin connector.
- Close your computer case and connect the AC power cord to the power supply AC inlet.
- Attention! When Smart Zero Fan System is turned on, the fan will not operate until the power supply reaches approximately 30% of rated load; It is normal if the fan does not operate when computer is at a low working load.
- This PSU is equipped with a patented 16.8 million colors Riing Duo 14 RGB Fan which features:
- (1) Button controlled 8 lighting modes The lighting modes/colors can be changed when the Mode/Color button is pressed. You can e ither choose Wave, Spiral, Flow, Heartbeat, Ripple, Full Lighted, Spectrum Mode, or you can switch off the LEDs. Long pressing the Mode button can reset settings to default. The fan also has a built-in memory which can automatically recover the previous lighting mode after you restart the PSU.
- (2) Synced with all RGB lighting devices on you system The lighting effects can be synced through the motherboards with ARGB Sync function. After switching off the PSU, connected the ARGB Sync Cable to the ARGB Sync Header on the PSU and to the +5V ARGB header on the motherboard (Caution: This power supply does not support +12V RGB header). Next, install the software provided by your motherboard’s vendor, such as ASUS AURA SYNC, GIGABYTE RGB FUSION, mis MYSTIC LIGHT SYNCor AsRock Polychrome software. Finally, choose your favorite lighting theme. Every time you turn on the PC, the chosen lighting theme will be automatically recovered only when the software boots up.
Total Protection
Over Voltage Protection
-
Short Circuit Protection
Activated when any DC rails short-circuited. -
Over Power Protection
The power supply shall be shut down and latch off, if the wattage of the power supply is 120%-150% over continuous power.
Environments
Trouble-Shooting
If the power supply fails to function properly, please follow the troubleshooting guide before applying for service:
- Is the power cord plugged properly into an electrical outlet and into the power supply AC inlet?
- Please make sure the I/O switch on the power supply is switched to I
- Please make sure all power connectors are properly connected to all the
- If connected to a UPS unit, is the UPS on and plugged in?
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>