thermaltake G700 RGB Gaming Desk User Manual

thermaltake G700 RGB Gaming Desk

WARNING:

FAILURE TO COMPLY WITH OR OBSERVE ALL ASSEMBLY, SAFETY AND OPERATION INSTRUCTIONS AND WARNINGS REGARDING THE USE OF THIS PRODUCT MAY RESULT IN SERIOUS BODILY INJURY.

IMPORTANT INFORMATION

Please read this manual carefully

• This document contains all relevant safety regulations. Any non-conforming use may result in personal injury or mechanical damage.
• Please read this operation manual carefully before use. The manual provides a lot of important information about the safety, use, assembly and subsequent maintenance of the lifting table; it can avoid many unnecessary injuries.
• If this desk is sold, please provide this manual to the buyer.
• Do not sit or stand on the desk. Do not crawl or lie under the desk.
• Failure to comply with or ignore any safety requirements, assembly instructions, user operations and related warnings may result in serious personal injury or mechanical damage. Please operate and Before assembly, really understand the relevant regulations.
• This product is not a toy. Please be careful.
• Ensure that you have received all parts according to the component checklist prior to installation. If any parts are missing or faulty, telephone your local distributor for a replacement.
• If the supply cord is damaged, it must be replaced by the manufacturer and its service agent in order to avoid a hazard.
• This product is not intended for use by young children without supervision.
• This product contains small items that could be a choking hazard if swallowed. Keep these items away from children.
• This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.
• This product can be used by children from 8 years old (supervised) to Adult. Users with disabilities or lack of experience and operating knowledge should be supervised and given careful instructions prior to using this product. The desktop should never be sat on and children should be prohibited from having unsupervised contact with the product.
• Cleaning and user maintenance shall not be made by children without supervision. Do not over tighten screws during installation.

Do not over tighten screws during installation.

CAUTION

• Please place the product away from corrosive gas, water and dusty environments.
• Alteration or modding of any factory components outlined in the checklist will automatically void your warranty.

USE & LIABILITY

• This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury
• The height adjustable desk is designed for indoor use and dry work areas only. The desk height is adjustable so that it can be positioned at the most suitable height. Any other use is at the suser’s risk. Under no circumstances does the manufacturer accept warranty claims or liability claims for damages caused from improper use or handling of the desk.

SPECIFICATIONS

PARTS LIST

It is recommended to use hand tools & electric hand tools / no inclusion

Check Before Assembling

Check if the rubber pads on the Crossbar assemble them back. 1-A and Side Brackets 1-E have fallen off. If any, find the pads in the package and

Installation Instruction

Please prepare a spacious area for installation, and put a shipping blanket on the area to prevent scratches.

Route the cable into the slot on the desktop.

Route the cable of the controller out from the lifting column after locating the frame.

Adjust the lifting columns to align all holes, and then tighten the screws.

Connect each unit as shown. Use the Extension Cable 1-1 to connect the column on the far side.

Elevate the entire table as shown.

If needed, move the sliding plates for installing the screws.

Route the light strip from the side hole of the desktop, and connect it to the adapter.

Manage cables inside the crossbar, and assemble the baffle.

Ensure the translucent side of light strip facing outside, and put on decorative plates.

Magnetic Cable Clips Usage

Put the clips on the desired position of the decorative covers.

Adjusting the Sliding Blocks

Tighten the knob to fix the blocks, and loosen it to slide.

Controller Instruction

Memory Settings

Adjust the desk to the desired height, press M and the display will show 5- Press I or 2 to save the current height as 5-1 or 5-2. Press M or E to adjust the desk to the position automatically.

Lighting Mode

Press to switch the lighting effects, and press M to set the desired one.

Highest and Lowest Limit Settings

Adjust the desk to the desired height, press M and the display will show 5- . Press and then press M and hold m for 3 seconds. When the display shows 999 it indicates the current height is the maximum height limit; while 00.0 indicates the minimum height limit. Press and hold m again for 3 seconds, and the display will show 555 indicating removing all limit settings.

Lock and Unlock

Press and hold M 8 seconds until the display shows the controller. Repeat the operation to unlock. to LOC

Reset the System (Adjust the desk to the lowest position first.)

Press and hold y for 5 seconds until the display shows Asr to reset the system. Repeat the operation to exit reset mode.

Adjust the Actual Minimum Height Number

In Asr reset mode, press and hold m for 5 seconds, and the display will flash. Press to adjust the display height to the actual minimum height. After 5 seconds, it will back to the list, indicating the setting is completed (only modify the display value).

Switch the One-Touch/Constant-Touch Memory Program

In Asr reset mode, press and hold for 5 seconds to switch the memory program. 10.1 indicates “one-touch memory program”–only press 1 or 2 once to reach memory height; 10.2 indicates “constant-touch memory program”–keep pressing 1 or 2 until it reaches memory height.

CM/INCH Conversion

In Asr reset mode, press and hold ) for 5 seconds to switch CM/INCH display units. 10.3 indicates “CM”, and 1D.4 indicates “INCH”.

Adjust Collision Sensitivity

In Asr reset mode, press and hold  for 5 seconds to adjust the sensitivity. 10.5 indicates high sensitivity, 10.5 indicates middle sensitivity, and 110.7 indicates low sensitivity.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>