Curtron PP-C-120-6096 Polar-Pro SWINGING DOORS Owner’s Manual
- June 3, 2024
- Curtron
Table of Contents
Curtron PP-C-120-6096 Polar-Pro SWINGING DOORS
_“Our Input for Your Success”_
BRACKET SIZE: ❏17” ❏23” ❏29”
OPTIONS:
❏ Vision Strip
❏ Impact Plates
COLOR:
❏ Clear
❏ Orange
❏ Gray
❏ Black
❏ White
❏ Blue
MOUNTING:
❏ #1 Inside Surface
❏ #2 In-Jamb
❏ #3 Wall/In-Jamb
Date of Purchase:
Thank you for choosing a Curtron quality product.
Your POLAR-PRO™ Swinging Door was manufactured to your specific cooler or
freezer doorway width and height. Although installation is not complicated,
you will need a helper.
Do not use nails to attach the door panel brackets. 1/4” x 11/ 2” screws(6)
and washers(6) are included.
CHECK YOUR ORDER
The thickness of your door jamb will determine which mounting method to use. While standing inside the cooler or freezer, measure from the back of the closed door to the inside wall surface. (See drawings below.)
2 Door Panels are attached to the inside wall surface. For Mounting
Instructions, see page 3.
2 Door Panels are attached to the inside of the doorway opening using both
door jambs.
For Mounting Instructions, see page 4.
2 Door Panels are placed on the inside of the doorway opening, but use the
inside wall surface for mounting. For Mounting Instructions, see page 5.
#1. INSIDE SURFACE MOUNTING
CAUTION: Make sure that the door jamb is strong enough to support the weight and force of the door. If questionable, check with cooler/freezer manufacturer.
Do not disassemble the PVC panel from the bracket or remove the hinge pin from the mounting plate
NOTE: There is a Left and Right Door Panel, unless otherwise specified.
Place the right bracket mounting plate with the PVC panel attached, against
the inside right corner of the doorway opening. Mark the 6 holes. (See Fig. 1)
MPORTANT: The panel must be able to move freely beneath the door header and there should be no gap between the door panel and the header. Remove the unit and drill the holes. NOTE: A 5/ 32” drill bit should be used.
Finally, put each unit in place and screw down tightly to the interior wall
using the supplied 1/4” x 11/2” screws and washers. (See Fig. 2)
#2. IN-JAMB MOUNTING
CAUTION: Make sure that the door jamb is strong enough to support the weight and force of the door. If questionable, check with cooler/freezer manufacturer.
Do not disassemble the PVC panel from the bracket or remove the hinge pin from the mounting plate.
NOTE: There is a Left and Right Door Panel unless otherwise specified
First, remove the Wall Mounting Plate from the “U” Bracket. (See Fig. 3)
From inside the cooler/freezer, measure 21/4” in at the very top of the jamb
and place a mark. Using a mason’s level, draw a straight plumb line 7” down
from the mark. (See Fig.4 )
Place the “U” Bracket, with the PVC panel attached, against the jamb, touching
the header and using the line to keep the panel vertically straight. Mark the
4 holes. Remove the unit and drill the holes. (See Fig. 5 )
NOTE: A 5/32” drill bit should be used.
Next, do the same procedure on the other side of the doorway opening.
Finally, put each bracket/panel in place and screw down tightly to the door
jamb using the supplied 1/4” x 11/2” screws and washers. (See Fig. 6 )
#3. WALL / IN-JAMB MOUNTING
CAUTION: Make sure that the door jamb is strong enough to support the weight and force of the door. If questionable, check with cooler/freezer manufacturer.
Do not disassemble the PVC panel from the bracket or remove the hinge pin from the mounting plate.
**NOTE: There is a Left and Right Door Panel unless otherwise specified. However, when using this mounting method, the panels are reversed from Method
1.**
Place the right Wall Mounting Plate with the PVC panel attached, against the
inside right corner of the doorway opening. Mark the 6 holes. (See Fig. 7)
IMPORTANT: The panel must be able to move freely beneath the door header
and there should be no gap between the door panel and the header.
Remove the unit and drill the holes.
NOTE: A 5/ 32” drill bit should be used.
Finally, put each unit in place and screw down tightly to the interior wall
using the supplied 1/4” x 11/2” screws and washers. (See Fig. 8)
FINAL ADJUSTMENTS
CENTERING
If the panels are not aligning at the center overlap, a simple adjustment can be made.
Loosen (DO NOT REMOVE) the 2 adjusting nuts. By moving the adjustment plate to
one side or the other, it will force the panel to move in the opposite
direction. (See Fig. 9) i.e. Move the plate to the right…the panel will go
left. (See Fig. 10) Once both panels are exactly perpendicular to one another,
tighten the adjustment nuts.
TENSION
If the door panels are not returning to a completely sealed position, increased tension might be needed.
To tighten or loosen the cam spring tension, first loosen the lock nut at the
bottom of the mounting bracket.
Using an allen wrench, move the tension screw clockwise to tighten or
counterclockwise to loosen. Once the proper tension is determined, tighten the
locknut.
OTHER TMI PRODUCTS
STRIP DOORS
BULK PVC ROLLS & STRIPS
MEGA-PRO™ SWINGING DOORS
RIP-A-STRIP™
ENCLOSURES
INDUSTRIAL CURTAINS
DOCK ACCESSORIES
AIR DOORS
DESIGN ENGINEERING
TECHNICAL ASSISTANCE
SPECIAL PACKAGING AND
DELIVERY SERVICES
800•888•9750
TMI, LLC • 5350 Campbells Run Road • Pittsburgh, PA 15205-9738 • 412.787.9750
Fax: 412.787.3665 • Web Site:www.tmi-pvc.com •
E-Mail: customer-service@tmi-pvc.com
Copyright © 2007 TMI, LLC Catalog No. II-PPSD-06/07
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>