Tefal BL91HD31 Blender Instruction Manual

Tefal BL91HD31 Blender

DESCRIPTION

A 1 Middle cap
2 Lid
3 Plastic Tritan jar
B 1 Seal
2 Powelix blades unit
3 Locking ring
C Motor unit
D Tamper E* 1 On the go bottle lid
2 On the go bottle
3 Seal
4 Powelix life blades unit
5 Locking ring

F* Screen
G ON/OFF button
H Blender jar lock indicator
I On the go bottle lock indicator
J Program function
K Manual setting function
L Pulse function
M Cleaning function

WARNING:

The safety instructions are part of the appliance. Read these instructions carefully before using your new appliance for the first time. Keep them in an accessible place so that you can refer to them later. The appliance will only work if the jar or the bottle is correctly positioned on the motor unit (C) and if the lid is locked onto the jar.

BEFORE USING YOUR APPLIANCE FOR THE FIRST TIME

Before using your appliance for the first time, rinse the parts that come into contact with food (jar, bottle, lids and middle cap) with soapy water.

WARNING: Do not immerse the appliance in water (neither the motor unit nor the blades unit (C and B2). Never put the motor unit (C) under running water. Clean the appliance with a damp cloth and dry it carefully. The blades are extremely sharp.

Make sure all the packaging has been removed before operating the appliance.

ASSEMBLING AND FITTING THE JAR

Moisten the seal (B1) (even if already fitted on the blades unit (B2)). Be careful to correctly fit the seal (B1) back onto the blades unit (B2) the correct way up (Fig. 1). Place the blades (B2) on the locking ring (B3) (Fig. 2). Turn the jar upside down and fit the locking ring with blades on the base of the jar (Fig. 3). Lock it by rotating to lock ring in the clockwise direction (Fig. 3). Make sure the locking ring is locked correctly: the arrow on the jar must be aligned with the arrow on the locking ring (Fig. 3).

Add the ingredients into the assembled jar without exceeding the maximum level indicated (Figures 4 and 5): 1.75 L for thick mixtures 1.5 L for liquid preparations
Warning: Do not pour boiling liquids (over 80°C/176°F) into the jar.

Lock the lid on the jar and lock in the clockwise direction (Fig. 6). Make sure the lid is locked correctly: the point on the lid should be aligned with point on the handle (Fig. 7). Lock the middle cap in position on the lid and lock it by rotating it in the clockwise direction. If the lid is not correctly locked, your appliance will not start; Position the jar correctly on the motor unit (Fig. 8): the point on the jar should aligned with the lock on the motor unit (Fig. 8). A jar logo
will appear on the screen (H) and a beep signal will sound.

ASSEMBLING AND FITTING THE ON THE GO BOTTLE

Moisten the seal (E3) (even if already fitted on the blades unit (E4)). Be careful to correctly fit the seal back onto the blades unit (E4) the correct way up (Fig 9). Add the ingredients into the bottle without exceeding the maximum level indicated:

• 400ml for thick mixtures
• 600ml for liquids
  Warning: Do not pour boiling liquids (over 80°C/176°F) into the bottle.

Place the blades unit (E3+E4) on the locking ring (E5) (Fig. 10). Turn the jar (E2) upside down and assemble the locking ring with the blades on the base of the jar (Fig. 11) by locking it in the clockwise direction.
Turn the bottle upside down and position it correctly on the motor unit. Lock it by rotating it in the clockwise direction (Fig. 12). A bottle signal will sound.

USING YOUR APPLIANCE

Put the appliance on a flat, stable, heat-resistant surface away from heat sources or water.

Plug your appliance in and select your program (J) or manual settings (K) (time and speed) and press the Start/Stop button (G).
With the jar (A) you can change the blending speed from 1 to 9 by pressing speed program then the setting +/- (“H” being the maximum speed), and you can also set up the running time by pressing time program then setting +/- (K) between 5 seconds and 3 minutes.

With the on the go bottle (E) you can manage the blending speed from 1 to 7 by pressing  the setting +/- buttons (K). You can also set up the running time by pressing the setting +/- buttons (K) between 5 seconds and 90 seconds. Your blender will stop automatically at the end of the program. If you want to stop the blender before the automatic end of the program, press on the Start/Stop button (G).

When using the blender, do not use any accessories other than the pusher to avoid damaging the bowl.

Less than 3 minutes of mixing are enough to blend liquids for most recipes.

To add ingredients while blending, remove the middle cap from the lid and add the ingredients through the feeder hole. Beware of the risk of spatter.

WARNING: After running one cycle in the blender for the maximum processing time, let the blender rest for 1 minute before operating it again. After using the blender for a maximum of two cycles, stop the appliance and leave to cool to room temperature (takes about 2 hours). The appliance is fitted with overload protection. This prevents the motor from being damaged by abnormal usage.

If the appliance switches off during operation, proceed as follows: Unplug and leave to cool down for around 15 to 20 minutes. Reconnect the appliance to the power supply and resume blending.

After approx. 3 minutes without use, your appliance will start a standby mode. To switch on your appliance again, press the Start/Stop button (G).

ROUGH CHOPPING SMALL QUANTITIES

Accessory used: assembled chopper Chop in a few seconds by pulsing (L): peanuts, almonds etc. Model 1600 w: quantity/max. time: 140 g peanuts/8 seconds or 150 g almonds/8 seconds

adjusted between 30 seconds to 80 seconds
| Use this program to make ice cream: blending frozen fruits with fresh cream or yoghurt| Sorbet: 450 g of frozen raspberries + 240 g of milk + 75 g of powdered brown sugar The pusher should be used to help mix.| Default time: 1 min 10 secs
| Use this program to crush ice cubes and make crushed ice| 8 ice cubes maximum| Default time: 40 seconds Can be adjusted between 10 seconds to 50 seconds
| Use this program to make light dough for waffles, cakes, pancakes, clafoutis, brownies, etc. Not suitable for making heavy dough like bread, brioche, pizza etc.| Yoghurt cake: Add the ingredients to the jar in this order: 120 g of yoghurt + 210 g of powdered brown sugar + 7.5 g of vanilla sugar + 3 eggs + 125 g of sunflower oil + 85 g of corn flour + 65 g of ground almonds + 140 g of flour + 11 g of baking powder. Pour the mixture into a mould and bake for 50 minutes at 180°C.| Default time: 1 min 15 seconds Can be adjusted between 30 seconds to 2 minutes

| Use this program to clean your blender| 200 ml water + 1 drop of washing-up liquid| 30 seconds
| Use this program to make smoothies: blending fresh fruits/vegetables with milk or yoghurt| 100 g of carrots + 50 g of bananas + 50 g of celeriac + 250 g of orange juice| Default time: 45 seconds Can be adjusted between 30 seconds to 60 seconds
| Use this program to crush ice cubes and make crushed ice| 4 ice cubes maximum| Default time: 40 seconds Can be adjusted between 10 seconds to 50 seconds
| Use this program to clean your blender| 200 ml of water| 30 seconds

The pulse function (L) can still be used when no program is running.

WARNING: Strong foods may stain the inside of the bowl, but this does not affect the efficiency of the appliance. Frozen foods should be no bigger than a walnut. Do not add hot liquid above 80°C as it can be ejected out of the appliance due to a sudden build up of steam.

AFTER USING YOUR APPLIANCE

Unplug the appliance.
Pour the mixture out of the jar since it is not designed for storing food in the refrigerator or in the freezer.
Use a damp cloth to clean the motor unit. Dry off carefully. Never immerse the motor unit in water. you can use the cleaning program (M).
Pour in 200 ml of water. You can add a drop of washing-up liquid into the water but nothing else
The lid (A2), the on the go bottle (E2), the lid of the on the go bottle (E1) and the middle cap (A1) can be cleaned in the dishwasher but the jar (A3), the Powelix blades unit (B2 or E4)), the titanium-coated Powelix life blades unit must not be washed in dishwasher. Do not fully immerse the blades (B2 or E4) or leave them under water for a long time. (A).

WHAT TO DO IF YOUR APPLIANCE DOES NOT WORK?

appliance into an outlet providing the sa me voltage as specified on the a pplia nce’s rating plate.
The ble nder jar is not co rrectly positioned or l oc k ed on the moto r u n it.|  Check t hat the ble nder jar is correctly po s i t i o n e d on t h e m o tor un i t as expla i ned i n the instructions.
The power switch is in the OF.F position.| Follow the inst ructions  fo r starting your a pplia nce.
In case of a software bug.| Un plu g the a ppliance, wait few minutes and plug in again.
The a ppliance switches off when in use.| Overload| Follow the inst ructions in t he Overload sect i on.
Excessive vib<ation.| The app liance is not placed on a flat surface.| Place the appliance on a flat surface.
Volume d ingredients is too high.| Reduce the quantity of ingredients in the a pplia nce.
leak from the lid| Volume d ingredie nts is too high.| Reduce the quantity of ingredients in the applia nce.
The lid is not co,rectly positiooed.| Lock t he lid sec urely onto the blender jar.
leak from the base of the blender ja r.| The blades are not correctly posi tioned.| Fit Lie locking ring (B3, C3) ( Fig. 2) and lock it by rotati ng the lock notch in t he clockwise di recti on (Fig. 2). Make sure the locking ring is lockedcorrectly: the point on the ja r s hould be aligned with the lock ( Fig. 9).
The blades have difficulty turning.| The pieces of food a re too large or too hard.| Reduce the quantity or si ze of mixed i ng r edients .
The blended liquid is too ho t o r the silicone sea l is bent.| Replace the seal with a new one.
Leak from the base of the on the go bottle| The blades are not correctly positioned.| Place the blades unit on the top of the bott le and lock it by rotating the lock notch in the clockwise direction (Fig. 9).

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>