Kisi One-door Access Controller User Manual

June 5, 2024
Kisi

One-door Access ControllerUser Manual V2.2
1. Specifications:
1.1 Technical parameters:

Operating voltage

| DC 12V±10%| Storage| 1000 users
---|---|---|---
Operating current| < 100mA| Card type|

EM(standard) /Mifare(optional)

Operating temperature

| 0°C-60°C| Reading distance|

1-5CM

1.2 Factory Default:

Item

| Value| Item| Value
---|---|---|---
Authentication Mode| Card or Password(PIN)| Common PIN|

None

Unlocking Duration

|

5 S

| |

1.3 Light and Sound indicates:

Light: red and green

Light Description

| Indicates
---|---
Red light flash every 2 sec(Slow flash)|

Standby state

Green light flash every 0.5sec(Fast flash)

| Pending further operation
Red light is always ON|

Programming state

Green light is always ON

| Unlocking state
Red and green light flash alternately|

Restoring Factory Programming Password

Sound: beep

Sound Description

| Indicates
---|---
1 short beep|

Valid input

3 short beeps

| Invalid input
1 long beep|

Programming state

3 long beeps

|

Restoring Factory Programming Password

2. Installations Guide:

JP1:

NO

| Mark| Color| Function
---|---|---|---
1| +12V| Red|

Power+

2

| GND| Black| Power-
3| PUSH| BLUE|

Low level output

4

| OPEN| Yellow| Door Release
5| BEL+| Grey|

High level Input

6

| BEL-| White|

Voltage output

JP2:

NO

| Mark| Color| Function| Remark
---|---|---|---|---
1| NC| Brown| Relay NC output|

2

| COM| Blue| Relay Com output|
3| NO| Purple| Relay NO output|

2.1 Wiring diagram

Kisi One-door Access Controller

3.Programming Guide

3.1 Programming Guide: (Programming Password Default: 123456)    Remark: All password can be 3~6 digits

Programming Item

| Press key and swipe card operations|

Remark

---|---|---

Basic Function

| Change Programming Password (Pro.PW)| # Pro.PW # 0 new Pro.PW # new Pro.PW

| If Pro.PW lost, perform 3.2 to reset to Factory Default (123456)

Add user card| # Pro.PW # 1 swipe cards #| If add series cards, swipe cards continuously
Configure Common PIN| # Pro.PW # 21 new Common PIN #| Common PIN is only one, Unlocking method: Enter Common PIN then press [#]
Delete all users| # Pro.PW #40 0000 #| Delete all cards and PIN except Common PIN
Delete user by swiping card| # Pro.PW # 41 swipe cards #| If delete series cards, swipe cards continuously

Expand Function

| Add user by input User ID| # Pro.PW # 22 4-digit User ID swipe card #| Add user card or PIN by user’s ID. User ID must be 4 digits and cannot be reused (3 beeps means reused and need to enter a new). If add series users repeat the operation. More about User ID see 3.3
Add PIN| # Pro.PW # 23 4-digit User ID new PIN #
Delete user by User ID| # Pro.PW # 42 4-digit User ID #
Delete user by card No.| # Pro.PW # 43 card No. #| Card No. is 10-digit or 8- digit, device auto-identify
Configure Unlocking Duration| # Pro.PW # 5 XX #| XX is 2-digit (00~99). If XX is 00, Unlocking Duration is 0.2s
Configure Authentication Mode| # Pro.PW # 6 XX #| XX can be 01(only Card)/02(Card or PIN)/03(Card & PIN)
Reset Factory Default| # Pro.PW # 8 99 #| Except Programming Password and Manager Card

3.2 How to reset to Factory Programming Password(123456)
Step1, Turn off power and connect OPEN and GND terminal. Turn on power then there is 3 long beeps with green and red light flashing alternately.
Step2, Turn off power, disconnect OPEN and GND terminal. Turn on power again. Initializing Programming Password is completed.

3.3 Use ID explanation
User ID is 4-digit number from 0001 to 9999. There is no User ID for the users added by command [1]. Perform command [40] to clear all User ID.

4. Other extensions

4.1 How to change PIN
Swipe card or press PIN to unlock within 5s press [#] for 3s until the green light flash fast, then press [new PIN#new PIN#], the new PIN changed successfully with a long beep.

4.2 Authentication Mode for Card & PIN function
Step1, When Authentication Mode is [Card or PIN] (factory default), according to the step 3.4 to configure the PIN of the card.
Step2, Press [#Programming Password#603#] to configure Authentication Mode to be [Card & PIN].
Step3, Swipe user’s card with green light fast flash then input [PIN#] with green light normally ON, the door opened successfully.

4.3 Door open function description:
When the credit card or password is normally opened, press the 7, 9 digit key to keep the door open. When the door is always open, only once the credit card, password, or the door button is opened again, the exit is always open.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals