Jandy TruFit – Bubbler Eyeball and Snorkel Owner’s Manual

: June 7, 2024
: Jandy

Table of Contents

Section 1. Prepare the Bubbler
- Product Contents
- Remove Bubbler Lens
Section 2. Assembly
Section 3. Installation

OWNER’S MANUAL
ENGLISH

TruFitTM Bubbler
Eyeball and Snorkel

WARNING
FOR YOUR SAFETY – This product must be installed and serviced by a contractor who is licensed and qualified in pool equipment by the jurisdiction in which the product will be installed where such state or local requirements exist. The maintainer must be a professional with sufficient experience in pool equipment installation and maintenance so that all of the instructions in this manual can be followed exactly. Before installing this product, read and follow all warning notices and instructions that accompany this product. Failure to follow warning notices and instructions may result in property damage, personal injury, or death. Improper installation and/or operation will void the warranty.

Improper installation and/or operation can create unwanted electrical hazard which can cause serious injury, property damage, or death.

ATTENTION INSTALLER – This manual contains important information about the installation, operation and safe use of this product. This information should be given to the owner/operator of this equipment.

Important Safety Instructions IMPORTANT SAFETY INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS READ AND FOLLOW ALL INSTRUCTIONS

When installing and using this electrical equipment, basic safety precautions should always be followed, including the following:

DANGER

RISK OF ELECTRICAL SHOCK OR ELECTROCUTION. This underwater light must be installed by a licensed or certified electrician in accordance with the National Electrical Code® and applicable local codes and ordinances. In Canada, the Canadian Electrical Code and all applicable local codes and ordinances must be adhered to. Improper installation will create an electrical hazard, which could result in death or serious injury to pool or spa users, installers, or others due to electrical shock, and may also cause damage to property. Read and follow the specific instructions below.

WARNING

Before installing this underwater lighted bubbler, read and follow all warning notices and instructions accompanying this light. Failure to follow safety warnings and instructions can result in severe injury, death, or property damage.
Visit www.jandy.com for additional free copies of these instructions or call Zodiac Technical Support at 800.822.7933 (U.S.) or 888.647.4004 (Canada)

WARNING

RISK OF ELECTRICAL SHOCK OR ELECTROCUTION, which could result in serious injury or death. The Jandy® Pro Series Nicheless LED Lights are only available for 12-volt AC power. For supply connection, use only an isolating low voltage power supply with ungrounded output, evaluated and listed by a NRTL for swimming pool use.

ATTENTION INSTALLER
This manual contains important information about the installation, operation and safe use of this product. This information should be given to the owner/operator of this equipment.

SAVE THESE INSTRUCTIONS

Section 1. Prepare the Bubbler

Product Contents

ITEM	DESCRIPTION

1

|

Snorkel

2

|

Lens Removal Tool (included with purchase of Jandy lights)

3

|

Eyeball

4

|

Metal Sleeve

5|

Lens

Remove Bubbler Lens

Turn off the power to the pump. If the pump is located below the water level, close the isolation valves on the suction and discharge sides of the pump to prevent backflow of water.
Using the lens removal tool, insert the four prongs into the top of the lens.

NOTE: Lens Removal Tool is needed to complete this installation.

Figure 1. Insert Removal Tool

Figure 2. Remove Existing Lens

3. Rotate counter-clockwise to extract the lens.
4. Remove the existing lens from the bubbler body.

Section 2. Assembly

Insert the eyeball into the center of the lens opening.
Figure 2. Insert Eyeball
Rotate the eyeball 90 degrees and push the eyeball into the center of the lens. Make sure the eyeball faces up.

Figure 3. Rotate Eyeball
Insert and pull the snorkel through the bottom of the eyeball until it locks in place.
NOTE: Snorkel only compatible with the 3/4” eyeball.

Figure 4. Insert the Snorkel
Make sure the lip of the snorkel snaps over the edge of the eyeball.

Figure 5. Insert the Snorkel

Section 3. Installation

Insert the snorkel into the bubbler body.
Turn the lens clockwise. Make sure it fits properly inside the body.
Figure 6. Insert the Snorkel

Figure 7. Snorkel Installed
The snorkel is adjustable so that proper water flow can reach the surface. The length of the snorkel can be trimmed so that the plume height of the bubbler can be set to your preference.
Cut at least 1” at time to get the preferred plume height.
NOTE: The snorkel can be adjusted within a 45 degree angle only.

Zodiac Pool Systems LLC
2882 Whiptail Loop # 100, Carlsbad, CA 92010
Jandy.com | 1.800.822.7933

Zodiac Pool Systems Canada, Inc.
3365 Mainway, Unit 2 Burlington, ON L7M 1A6
Jandy.ca | 1.888.647.4004

©2020 Zodiac Pool Systems LLC. All rights reserved. ZODIAC® is a registered trademark of Zodiac International, S.A.S.U., used under license. All other trademarks are the property of their respective owners.
H0666200 REV C