ARTECTA RIBBON2835 Strip LED 24V Blanc chaud 2700K 240 LEDs/m 23550lm Instruction Manual

June 3, 2024
ARTECTA

RIBBON2835 Strip LED 24V
Blanc Chaud 2700K 240 LEDs/m 23550lm
Instruction Manual
ARTECTA RIBBON2835 Strip LED 24V Blanc chaud 2700K 240 LEDsm
23550lm

Product Description

The Ribbon Series are IP20 LED strips for indoor installation at dry places. They are suitable for mounting in an aluminum profile. The Ribbon Series are available in various color temperatures and as RGB, RGBW, and RGBA options.
For complete product specifications visit the respective product page on our website www.highlite.com.

Safety Instructions

Important
Read and follow the instructions in this user manual before installing, operating, or servicing this product.
DANGER
Installation, service, and maintenance of this product shall be carried out only by qualified persons.
This product must be installed in accordance with the applicable national and international standards for electrical installations.
Improper installation may lead to hazardous situations and material damage.

Installation Site Requirements

Attention
The LED strips are suitable for installation only in dry locations. Not suitable for outdoor installation.

It is recommended to install the LED strips in an aluminum profile.
An aluminum profile provides good heat dissipation.
Do not install the LED strips:

  • in wet locations
  • at a place where the LED chips are exposed to direct sunlight
  • near heat-generating devices.

Do not install the LED strips in environments with highly volatile substances, such as sulfur, chlorine, bromine, and VOC. This will reduce the life of the LED chips.
Make sure that the LED strips are installed at a place with:

  • ambient temperature between -20 °C and 50 °C
  • sufficient airflow.

Make sure that the mounting surface is clean and smooth, and free of grease or silicone oil.
Make sure that the mounting surface is thermally conductive and provides good heat dissipation.
If the LED strips are mounted on a metallic surface, make sure that the soldering points are insulated. If the soldering points are not insulated, short-circuit may occur.

Handling

ARTECTA RIBBON2835 Strip LED 24V Blanc chaud 2700K 240 LEDsm 23550lm -
HandlingDo not connect the LED strip to the electrical power supply when the LED strip is on the reel or when it is tightly coiled. This will damage the LEDs.
Do not put excessive pressure on the LED chips.ARTECTA RIBBON2835 Strip LED
24V Blanc chaud 2700K 240 LEDsm 23550lm - Handling2 You can bend the LED strip only along the vertical axis. The minimum bending radius is 20 mm.
Do not bend the LED strip with the LEDs on the inside.ARTECTA RIBBON2835
Strip LED 24V Blanc chaud 2700K 240 LEDsm 23550lm -
Handling3 Do not bend the LED strip on the horizontal plane.
Do not twist the LED strip.ARTECTA RIBBON2835 Strip LED 24V Blanc chaud
2700K 240 LEDsm 23550lm - Handling4 Do not fold or break the LED strips.
Do not cover the LED strips with any material during operation.

Installation

WARNING
Incorrect installation can cause serious injuries and damage to property.
The installation of this product shall be carried out only by qualified persons.
Disconnect the power supply in the area where the product will be installed.
Use a compatible constant voltage driver to connect the LED strip to the mains.
To connect the LED strip to the controller/driver or to other LED strips use wires with the sufficient cross-sectional area and current carrying capacity.

  1. Determine the location of all components.

  2. Cut the LED strip at the required length.ARTECTA RIBBON2835 Strip LED 24V Blanc chaud 2700K 240 LEDsm 23550lm - LED strip Cut the LED strip only at the marked cut line in the center of the solder pads. Make sure that the cut is made at 90°. The cutting tolerance is ±0.65 mm.ARTECTA RIBBON2835 Strip LED 24V Blanc chaud 2700K 240 LEDsm 23550lm - LED strip1Do not cut the LED strip at any other place. This will damage the internal circuit and the LEDs will not work.3

  3. Connect the LED strips if multiple LED strips are used.ARTECTA RIBBON2835 Strip LED 24V Blanc chaud 2700K 240 LEDsm 23550lm - LED Do not solder for a period longer than 3 seconds. Make sure that the soldering temperature is lower than 350 °C.
    Make sure that the polarity is correct when connecting multiple LED strips.

  4. Remove the protective tape from the LED strip. Be careful not to cause damage to the electronic components.ARTECTA RIBBON2835 Strip LED 24V Blanc chaud 2700K 240 LEDsm 23550lm - protective

  5.  Attach the LED strip to the mounting surface or to the aluminum profile.ARTECTA RIBBON2835 Strip LED 24V Blanc chaud 2700K 240 LEDsm 23550lm - surface Fold the LED strip at the marked cut line to mount the LED strip at a corner. Do not fold the LED strip more than once!ARTECTA RIBBON2835 Strip LED 24V Blanc chaud 2700K 240 LEDsm 23550lm - cut line You can also solder wires between 2 LED strips at a corner.

  6. Connect the LED strip to the controller/driver. Make sure that the polarity is correct.
    Setup example:ARTECTA RIBBON2835 Strip LED 24V Blanc chaud 2700K 240
LEDsm 23550lm - Setup example

Troubleshooting

Change in brightness or color temperature of the LEDs| Make sure that the run is not too long.
Voltage drop can cause the LEDs’ brightness to decrease.
---|---
Some LEDs do not work| Make sure that all connections are correct. Make sure that the LED strip is not
sharply bent. This can cause components to detach from the circuit board.
The LEDs are flickering| Make sure that the driver/power supply is compatible.
Make sure that all connections are correct.

Maintenance

Attention
Do not use detergent and/or water to clean this product.

This product is maintenance-free.
Use dry compressed air to clean the LED strip if necessary.
Do not use alcohol, solvents, detergents, and/or water. This will damage the LED strip.

Disposal

**** Dispose of this product by handing it to the respective collection point for the recycling of electrical and electronic equipment. Do not dispose of household waste.

©2021 Artecta. All rights reserved.
No part of this document may be copied, published, or otherwise reproduced without the prior written consent of Highlite International.
Design and product specifications are subject to change without prior notice.
For the latest version of this document and other language versions, please visit our website www.highlite.com or contact us at service@highlite.com.

Highlite International B.V.
• Vestastraat 2
• 6468 EX
• Kerkrade
• the Netherlands

Documents / Resources

| ARTECTA RIBBON2835 Strip LED 24V Blanc chaud 2700K 240 LEDs/m 23550lm [pdf] Instruction Manual
RIBBON2835 Strip LED 24V Blanc chaud 2700K 240 LEDs, m 23550lm, RIBBON2835, Strip LED 24V Blanc chaud 2700K 240 LEDs m 23550lm, Blanc chaud 2700K 240 LEDs m 23550lm, chaud 2700K 240 LEDs m 23550lm
---|---

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals