ARTECTA RIBBON5050 Strip LED 24V Blanc variable 60 LEDs/m 5525lm IRC85 User Manual

ARTECTA RIBBON5050 Strip LED 24V Blanc variable 60 LEDs/m 5525lm IRC85

Product Description

The Ribbon Series are IP20 LED strips for indoor installation at dry places. They are suitable for mounting in an aluminum profile. The Ribbon Series are available in various color temperatures and as RGB, RGBW and RGBA options. For complete product specifications visit the respective product page onourwebsite www.highlite.com.

Safety Instructions

Important
Read and follow the instructions in this user manual before installing, operating or servicing this product.

DANGER
DANGER Installation, service and maintenance of this product shall be carried out only by qualified persons.

This product must be installed in accordance with the applicable national and international standards for electrical installations. Improper installation may lead to hazardous situations and material damage.

Installation Site Requirements

Attention
The LED strips are suitable for installation only in dry locations. Not suitable for outdoor installation.
It is recommended to install the LED strips in an aluminum profile. An aluminum profile provides good heat dissipation. Do not install the LED strips:

• in wet locations
• at a place where the LED Chips are exposed to direct sunlight
• near heaf-generafing devices.

Do not install the LED strips in environments with highly volatile Substances, such as sulfur, chlorine, bromine and VoC. This will reduce the life of the LED chips.
Make sure that the LED strips are installed at a place with:

• ambient temperature between -20 °C and 50 °C
• sufficient airflow.

Make Sure that fhe mounting surface is Clean and smoofh, and free of grease or silicone oil. Make sure that the mounting surface is thermaly conductive and provides good heat dissipation. If the LED strips are mounted on a metallic surface, make sure that the soldering points are insulated. If the soldering points are not insulated, short-circuit may occur. 2021 Artecta. All rights reserved. No part of this document may be copied, published or otherwise reproduced without the prior written consent of Highlite International. Design and product specifications are subject to change without prior notice. For the latest version of this document and other language versions, please visit our website www.highlite.com or contact US af service@highlie.com.

Handling

• Do not connect the LED strip to electrical power supply when the LED strip is on the reel or when it is tightly coiled. This will damage the LEDs.

• Do not put excessive pressure on the LED chips.

• You can bend the LED strip only along the vertical axis. The minimum bending radius is 20 mm.

• Do not bend the LED strip with the LEDs on the inside.

• Do not bend the LED strip on the horizontal plane.

• Do not twist the LED strip.

• Do not fold or break the LED strips.

• Do not cover the LED strips with any material during operation.

Installation

WARNING
Incorrect installation can cause serious injuries and damage of property.
The insfallation of this product shall be carried ouf only by qualified persons. Disconnect the power supply in the area where the product will be installed. Use a compatible constant voltage driver to connect the LED strip to the mains. To connect the LED strip to the controller/driver or to other LED strips use wires with sufficienf cross-secfional area and current Carying capacity.

1. Determine the location of all components.

2. Cut the LED strip at the required length.

3. Connect the LED strips if multiple LED strips are used. Do not solder for a period longer than 3 seconds. Make sure that the soldering temperature is lower than 350 °C.
   Make sure that the polarity is correct when connecting multiple LED strips.

4. Remove the protective tape from the LED strip. Be careful not to cause damage to the electronic components.

5. Attach the LED strip to the mounting surface or to the .elorp munimula Fold the LED strip at the marked cut line to mount the LED strip at a corner. Do not fold the LED strip more than once! You can also solder wires between 2 LED strips at a corner.

6. Connect the LED strip to the controller/driver. Make sure that the polarity is correct.
   Setup example:

Troubleshooting

• Change in brightness or color temperature of the LEDs
  Make sure that the run is not too long. Voltage drop can cause the LEDs’ brightness to decrease.

• Some LEDs do not work
  Make sure that all connections are correct. Make sure that the LED strip is not sharply bent. This can cause components to detach from the circuit board.

• The LEDs are fickering
  Make sure that the driver/power supply is compatible.
  Make sure that all connections are cor-rect.

Maintenance

Attention
Do not use detergent and/or water to clean this product.

This product is maintenance-free.
Use dry compressed air to clean the LED strip if necessary.
Do not use alcohol, solvents, detergents and/or water. This will damage the LED strip.

Disposal

Dispose of this product by handing it to the respective collection point for recycling of electrical and electronic equipment. Do not dispose of with the household waste.

References

• Highlite International | Event technology for professionals | Highlite.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>