ARTECTA A0320220 Newark 30 W CCT Zoom 20°-60° Cool White 30 W LED Light User Manual

ARTECTA A0320220 Newark 30 W CCT Zoom 20°-60° Cool White 30 W LED Light

Introduction

Before Using the Product

Important
Read and follow the instructions in this user manual before installing, operating or servicing this product.

The manufacturer will not accept liability for any resulting damages caused by the non-observance of this manual.
After unpacking, check the contents of the box. If any parts are missing or damaged, contact your Highlight International dealer.

Your shipment includes:

• AR tecta New Port 30W CCT 38° (including track adapter)
• User manual

Intended Use

This device is intended for use as an architectural light spot. It is suitable for indoor installation in commercial and residential buildings. This device is suitable for household illumination.
Any other use, not mentioned under intended use, is regarded as non-intended and incorrect use.

LEDs Lifespan

The light output of the LEDs gradually decreases over time (lumen depreciation). High operating temperatures contribute to this process. You can extend the lifespan of the LEDs by providing adequate ventilation and operating the LEDs at the lowest possible brightness.

Text Conventions

Throughout the user manual the following text conventions are used:

• References: References to chapters and parts of the device are in bold lettering, for example: “Refer to 2. Safety”, “turn the adjustment handle (05)”
• Notes:
  Note: (in bold lettering) is followed by useful information or tips

Symbols and Signal Words

Safety notes and warnings are indicated throughout the user manual by safety signs.

Always follow the instructions provided in this user manual

• DANGER Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
• WARNING Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
• CAUTION Indicates a potentially hazardous situation, which, if not avoided, may result in minor or moderate injury.
• Attention Indicates important information for the correct operation and use of the product.
• Important Read and observe the instructions in this document.
• Provides important information about the disposal of this product.

Symbols on the Information Label

This product is provided with 2 information labels. One information label is located on the back side of the
track head. The other information label is located on the side of the track adapter.

The information labels contain the following symbols:

• This device is designed for indoor use.
• This device shall not be treated as household waste.
• Independent control gear
• SELV control gear, short-circuit proof

Safety

Important
Read and follow the instructions in this user manual before installing, operating or servicing this product.
The manufacturer will not accept liability for any resulting damages caused by the non-observance of this manual.

Warnings and Safety Instructions

DANGER
Danger for children

For adult use only. The device must be installed beyond the reach of children.

• Do not leave various parts of the packaging (plastic bags, polystyrene foam, nails, etc.) within children’s reach. Packaging material is a potential source of danger for children.

Attention
Power supply
Before connecting the device to the power supply, make sure that the current, voltage and frequency match the input voltage, current and frequency specified on the information label on the device.

Attention
General safety

• Do not shake the device. Avoid brute force when installing or operating the device.
• If the device fails to work properly, discontinue the use immediately.

Attention
This device shall be used only for the purposes it is designed for.

This device is intended for use as an architectural light spot. It is suitable for indoor installation in commercial and residential buildings.
This device is suitable for household illumination.
This device does not contain user-serviceable parts. Unauthorized modifications to the device will render the warranty void. Such modifications may result in injuries and material damage.

Attention
Before use, examine the device visually for any defects.

Attention
Do not expose the device to conditions that exceed the rated IP class conditions.

This device is IP20 rated. IP (Ingress Protection) 20 class provides protection against solid objects greater than 12 mm, such as fingers, and no protection against harmful ingress of water.

Requirements for the User

This product may be used by ordinary persons. Maintenance may be carried by ordinary persons. Installation and service shall be carried out only by instructed or skilled persons. Contact your Highlight dealer for more information.
Instructed persons have been instructed and trained by a skilled person, or are supervised by a skilled person, for specific tasks and work activities associated with the installation, service and maintenance of this product, so that they can identify risks and take precautions to avoid them.
Skilled persons have training or experience, which enables them to recognize risks and to avoid hazards associated with the installation, service and maintenance of this product.
Ordinary persons are all persons other than instructed persons and skilled persons. Ordinary persons include not only users of the product but also any other persons that may have access to the device or who may be in the vicinity of the device.

Description of the Device

The AR tecta New Port 30W CCT 38° is a compact LED spot suitable for indoor installation in shops, exhibition halls, showrooms and similar venues. It features 3 selectable pre-defined color temperatures: warm white (2700 K), neutral white (4000 K), and cold white (6000 K). The LED spot can be dimmed with an external dimmer.
The device is equipped with a 3-phase track adapter. The 3-phase track adapter is compatible with the AR tecta 3-phase track systems and with the most 3-phase tracks available on the market.

View and Dimensions

1. Track adapter
2. Track lock
3. Circuit selector (0, 1, 2 and 3)
4. Pivot connector
5. Color temperature selector (WW, NW, CW)
6. Track head
7. Zoom ring
8. Zoom mark

Product Specifications

Dimensions

Installation and Deinstallation

Safety Instructions

WARNING
Incorrect installation and deinstallation can cause serious injuries and damage of property.

Installation and deinstallation of the device must be carried out only by instructed or skilled persons. Follow all applicable European, national and local safety regulations concerning electrical installations in buildings and working at heights.
Before installing or reinstalling the device make sure that the track system is disconnected from power supply.

Personal Protective Equipment

During installation and deinstallation wear personal protective equipment in compliance with the national and site-specific regulations.

Installation Site Requirements

• The device can be used only indoors.
• The device can be mounted only to a 3-phase track system.
• The minimum distance to other objects must be bigger than 0,5 m.
• The maximum ambient temperature ta = 40 °C must never be exceeded.
• The relative humidity must not exceed 50 % with an ambient temperature of 40 °C

Mounting

The device can be mounted only to a 3-phase track system.

CAUTION
Restrict the access under the work area during mounting.

To mount the device, follow the steps below:

1. Disconnect the track system from the power supply.

2. Make sure that the circuit selector (03) is in OFF position (0) and the track lock (02) is in unlocked position, as shown in Fig. 04.

3. Align the flange of the track adapter (01) with the track, as shown in Fig. 05.

4.  Insert the track adapter (01) in the track and push it until it snaps into place.

5. Turn the track lock (02) clockwise to lock the device in the track, as shown in Fig. 07.
   

6. ) Select the circuit with the circuit selector (03). You can select 1-, 2- and 3-phase circuit, as shown in
   Fig. 08.
   

Attention
Do not slide the track adapter in the track to adjust the position of the device (see Fig. 09). This can damage the connectors. Remove the device from the track and install it at the new place. For more information on how to remove the device from the track, refer to 4.5. Dismounting on page 11.

Dismounting

CAUTION
Restrict the access under the work area during dismounting.

To dismount the device, follow the steps below:

1. Disconnect the track system from the power supply.

2. Let the device cool down before dismounting.

3. Set the circuit selector (03) in OFF position (0), as shown in Fig. 10.

4. Turn the track lock (02) counterclockwise to unlock the device (see Fig. 11).

5. Pull the track adapter (01) from the track (see Fig. 12)
   

Direction Adjustment

To adjust the angle of the device and the direction of the beam:

• Move the track head (06) around the pivot connector (04) to adjust the vertical position of the track head (06). The adjustment range is 0–90°.
• Turn the track head (06) around the pivot connector (04) to adjust the horizontal position of the track head (06). The adjustment range is 0–350°.
  

Connecting to Power Supply

This device is suitable for mounting only to a 3-phase track system. The device is connected to power supply when it is mounted to the track system.
Before installing or reinstalling the device make sure that the track system is disconnected from power supply.

Color Temperature Adjustment

You can adjust the color temperature of the LEDs.

Set the color temperature selector (05) to one of the following positions:

• CW (cold white) position – for a predefined color temperature of 6000 K
• NW (neutral white) position – for a predefined color temperature of 4000 K
• WW (warm white) position – for a predefined color temperature of 2700 K

Beam Angle Adjustment

You can adjust the beam angle of the light output.

Turn the zoom ring (07) clockwise or counterclockwise to adjust the beam angle of the light output (see Fig. 14).The adjustment range is 20° – 60°, at steps of 1°.

Troubleshooting

This troubleshooting guide contains solutions to problems which can be carried out by an ordinary person. The device does not contain user-serviceable parts.
Unauthorized modifications to the device will render the warranty void. Such modifications may result in injuries and material damage.
Refer servicing to instructed or skilled persons. Contact your Highlight International dealer in case the solution is not described in the table.

Maintenance

Preventive Maintenance

Attention
Before use, examine the device visually for any defects.

Basic Cleaning Instructions

To clean the device, follow the steps below:

• Disconnect the device from the electrical power supply.
• Allow the device to cool down for at least 15 minutes.
• Remove the dust collected on the external surface with dry compressed air and a soft brush.

Attention

• Do not immerse the device in liquid.
• Do not use alcohol or solvents.

Corrective Maintenance

The light source is not replaceable.
The device does not contain user-serviceable parts. Do not open the device and do not modify the device.
Refer repairs and servicing to instructed or skilled persons. Contact your Highlight International dealer for more information.

Transportation and Storage

Instructions for Transportation

• Use the original packaging to transport the device, if possible.
• Always observe the handling instructions printed on the outer carton box, for example: “Handle with care”, “This side up”, “Fragile”..

Storage

• Clean the device before storing. Follow the cleaning instructions in chapter 6.1.1. Basic Cleaning Instructions on page 13.
• Store the device in the original packaging, if possible.

Disposal

Correct disposal of this product
Waste Electrical and Electronic Equipment

This symbol on the product, its packaging or documents indicates that the product shall not be treated as household waste. Dispose of this product by handing it to the respective collection point for recycling of electrical and electronic equipment. This is to avoid environmental damage or personal injury due to uncontrolled waste disposal. For more detailed information about recycling of this product contact the local authorities or the authorized dealer.

Approval

Check the respective product page on the website of Highlight International (www.highlite.com) for an available declaration of conformity.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>