ARTECTA New Port 15W CCT 38 User Manual

ARTECTA New Port 15W CCT 38

Preface

• Thank you for purchasing this Artecta product.
• The purpose of this user manual is to provide instructions for the correct and safe use of this product.
• Keep the user manual for future reference as it is an integral part of the product. The user manual shall be stored at an easily accessible location.
• This user manual contains information concerning:
  • Safety instructions
  • Intended and non-intended use of the device
  • Installation and operation of the device
  •  Maintenance procedures
  • Troubleshooting
  • Transport, storage and disposal of the device
• Non-observance of the instructions in this user manual may result in serious injuries and damage of property.

ABOUT COMPANY

• ©2021 Artecta. All rights reserved.
• No part of this document may be copied, published or otherwise reproduced without the prior written consent of Highlite International.
• Design and product specifications are subject to change without prior notice.
• For the latest version of this document or other language versions, please visit our website
• www.highlite.com or contact us at service@highlite.com.
• Highlite International and its authorized service providers are not liable for any injury, damage, direct or indirect loss, consequential or economic loss or any other loss arising from the use of, or inability to use or reliance on the information contained in this document.

Introduction

Before Using the Product
Important
Read and follow the instructions in this user manual before installing, operating or servicing this product.

• The manufacturer will not accept liability for any resulting damages caused by the non-observance of this manual.
• After unpacking, check the contents of the box. If any parts are missing or damaged, contact your Highlite International dealer.
• Your shipment includes:
  • Artecta New Port 15W CCT 38°(including track adapter)
  • User manual

Intended Use

• This device is intended for use as an architectural light spot. It is suitable for indoor installation in commercial and residential buildings. This device is suitable for household illumination.
• Any other use, not mentioned under intended use, is regarded as non-intended and incorrect use.

LEDs Lifespan
The light output of the LEDs gradually decreases over time (lumen depreciation). High operating temperatures contribute to this process. You can extend the lifespan of the LEDs by providing adequate ventilation and operating the LEDs at the lowest possible brightness.

Text Conventions
Throughout the user manual the following text conventions are used:

• References: References to chapters and parts of the device are in bold lettering, for example:
• Notes: “Refer to 2. Safety”, “turn the adjustment handle (05)”
  Note: (in bold lettering) is followed by useful information or tips

Symbols and Signal Words
Safety notes and warnings are indicated throughout the user manual by safety signs.
Always follow the instructions provided in this user manual.

Symbols on the Information Label

• This product is provided with 2 information labels. One information label is located on the back side of the track head. The other information label is located on the side of the track adapter.
• The information labels contain the following symbols:

Safety

Important
Read and follow the instructions in this user manual before installing, operating or servicing this product.

The manufacturer will not accept liability for any resulting damages caused by the non-observance of this manual.

Warnings and Safety Instructions
DANGER
Danger for children
For adult use only. The device must be installed beyond the reach of children.

• Do not leave various parts of the packaging (plastic bags, polystyrene foam, nails, etc.) within children’s reach. Packaging material is a potential source of danger for children.
  Attention
  Power supply

• Before connecting the device to the power supply, make sure that the current, voltage and frequency match the input voltage, current and frequency specified on the information label on the device.
  Attention
  General safety

• Do not shake the device. Avoid brute force when installing or operating the device.

• If the device fails to work properly, discontinue the use immediately.
  Attention
  This device shall be used only for the purposes it is designed for.

• This device is intended for use as an architectural light spot. It is suitable for indoor installation in commercial and residential buildings. This device is suitable for household illumination.

• This device does not contain user-serviceable parts. Unauthorized modifications to the device will render the warranty void. Such modifications may result in injuries and material damage.
  Attention
  Before use, examine the device visually for any defects.
  Attention
  Do not expose the device to conditions that exceed the rated IP class conditions.

• This device is IP20 rated. IP (Ingress Protection) 20 class provides protection against solid objects greater than 12 mm, such as fingers, and no protection against harmful ingress of water.

Requirements for the User

• This product may be used by ordinary persons. Maintenance may be carried by ordinary persons. Installation and service shall be carried out only by instructed or skilled persons. Contact your Highlite dealer for more information.
• Instructed persons have been instructed and trained by a skilled person, or are supervised by a skilled person, for specific tasks and work activities associated with the installation, service and maintenance of this product, so that they can identify risks and take precautions to avoid them.
• Skilled persons have training or experience, which enables them to recognize risks and to avoid hazards associated with the installation, service and maintenance of this product.
• Ordinary persons are all persons other than instructed persons and skilled persons. Ordinary persons include not only users of the product but also any other persons that may have access to the device or who may be in the vicinity of the device.

Description of the Device

• The Artecta New Port 15W CCT 38° is a compact LED spot suitable for indoor installation in shops, exhibition halls, showrooms and similar venues. It features 3 selectable pre-defined color temperatures: warm white (2700 K), neutral white (4000 K), and cold white (6000 K). The LED spot can be dimmed with an external dimmer.
• The device is equipped with a 3-phase track adapter. The 3-phase track adapter is compatible with the Artecta 3-phase track systems and with the most 3-phase tracks available on the market.

View and Dimensions

1. Track adapter
2. Track lock
3. Circuit selector (0, 1, 2 and 3)
4. Pivot connector
5. Color temperature selector (WW, NW, CW)
6. Track head

Product Specifications

Electrical:

Input voltage:| 220–240 V AC, 50/60 Hz
Power consumption:| 15 W (at full output)
PFC:| 0,94
Physical:

Dimensions:| 240 x 189 x 62 mm (L x W x H) (with the track adapter)
Weight:| 0,57 kg (with the track adapter)
Track adapter:

Input voltage:| 220–240 V AC, 50/60 Hz
Input current max:| 0,08 A
Protection class:| II
Output voltage:| 16–40 V DC
Output voltage max:| 60 V DC
Output current max:| 0,35 A
Type output:| SELV
Phases:| 3
Optics:

Light source:| 15 W COB LED, non-replaceable
Dimmer:| External, TRIAC type
Beam angle:| 38°
Luminous flux:| 940 lm @ 2700 K

1050 lm @ 4000 K

1080 lm @ 6000 K

CCT (selectable):| WW – 2700 K NW – 4000 K CW – 6000 K
CRI:| 94
Movement:

Tilt range:| 0–90°
Turning range:| 0–350°
Construction:

Housing:| Aluminum
Color:| A0320200 – Black A0320201 – White
IP rating:| IP20
Finish:| Powder coated
Thermal:

Maximum ambient temperature ta:| 40 °C
Minimum ambient temperature:| -20 °C
Minimum distance:

Minimum distance from flammable surfaces:| 0,5 m
Minimum distance to lighted object:| 0,5 m

Dimensions

Installation and Deinstallation

Safety Instructions
WARNING
Incorrect installation and deinstallation can cause serious injuries and damage of property.

• Installation and deinstallation of the device must be carried out only by instructed or skilled persons.
• Follow all applicable European, national and local safety regulations concerning electrical installations in buildings and working at heights.
• Before installing or deinstalling the device make sure that the track system is disconnected from power supply.

Personal Protective Equipment
During installation and deinstallation wear personal protective equipment in compliance with the national and site-specific regulations.

Installation Site Requirements

• The device can be used only indoors.
• The device can be mounted only to a 3-phase track system.
• The minimum distance to other objects must be bigger than 0,5 m.
• The maximum ambient temperature ta = 40 °C must never be exceeded.
• The relative humidity must not exceed 50 % with an ambient temperature of 40 °C

Mounting
The device can be mounted only to a 3-phase track system.
CAUTION
Restrict the access under the work area during mounting.

To mount the device, follow the steps below:

1. Disconnect the track system from the power supply.
2. Make sure that the circuit selector (03) is in OFF position (0) and the track lock (02) is in unlocked position, as shown in Fig. 04.
3. Align the flange of the track adapter (01) with the track, as shown in Fig. 05.

4. Insert the track adapter (01) in the track and push it until it snaps into place.
5. Turn the track lock (02) clockwise to lock the device in the track, as shown in Fig. 07.

6. Select the circuit with the circuit selector (03). You can select 1-, 2- and 3-phase circuit, as shown in Fig. 08.

Attention
Do not slide the track adapter in the track to adjust the position of the device (see Fig. 09). This can damage the connectors. Remove the device from the track and install it at the new place. For more information on how to remove the device from the track, refer to 4.5. Dismounting on page 11.

Dismounting
CAUTION
Restrict the access under the work area during dismounting.

To dismount the device, follow the steps below:

1. Disconnect the track system from the power supply.

2. Let the device cool down before dismounting.

3. Set the circuit selector (03) in OFF position (0), as shown in Fig. 10.

4. Turn the track lock (02) counterclockwise to unlock the device (see Fig. 11).

5. Pull the track adapter (01) from the track (see Fig. 12).

Direction Adjustment
To adjust the angle of the device and the direction of the beam:

• Move the track head (06) around the pivot connector (04) to adjust the vertical position of the track head (06). The adjustment range is 0–90°.
• Turn the track head (06) around the pivot connector (04) to adjust the horizontal position of the track head (06). The adjustment range is 0–350°.

Connecting to Power Supply

• This device is suitable for mounting only to a 3-phase track system. The device is connected to power supply when it is mounted to the track system.
• Before installing or deinstalling the device make sure that the track system is disconnected from power supply.

Color Temperature Adjustment
You can adjust the color temperature of the LEDs.
Set the color temperature selector (05) to one of the following positions:

• CW (cold white) position – for a predefined color temperature of 6000 K
• NW (neutral white) position – for a predefined color temperature of 4000 K
• WW (warm white) position – for a predefined color temperature of 2700 K

Troubleshooting

• This troubleshooting guide contains solutions to problems which can be carried out by an ordinary person. The device does not contain user-serviceable parts.
• Unauthorized modifications to the device will render the warranty void. Such modifications may result in injuries and material damage.
• Refer servicing to instructed or skilled persons. Contact your Highlite International dealer in case the solution is not described in the table.
  Problem| Probable cause(s)| Solution
  ---|---|---

The device does not function

| No power to the device| ●          Check if the track system is connected to the power supply

LEDs are damaged

| ●          Disconnect the device and contact your Highlite International dealer. The light source is not replaceable.
No light or LEDs cut out intermittently| The power supply settings do not match local AC voltage and frequency| ●          Disconnect the device. Check the settings and correct, if necessary

Maintenance

Preventive Maintenance

Attention
Before use, examine the device visually for any defects.

1. Basic Cleaning Instructions
   To clean the device, follow the steps below:

2. Disconnect the device from the electrical power supply.

3. Allow the device to cool down for at least 15 minutes.

4. Remove the dust collected on the external surface with dry compressed air and a soft brush.
   Attention

  * Do not immerse the device in liquid.
  * Do not use alcohol or solvents.

Corrective Maintenance

• The light source is not replaceable.
• The device does not contain user-serviceable parts. Do not open the device and do not modify the device.
• Refer repairs and servicing to instructed or skilled persons. Contact your Highlite International dealer for more information.

Transportation and Storage

Instructions for Transportation

• Use the original packaging to transport the device, if possible.
• Always observe the handling instructions printed on the outer carton box, for example: “Handle with care”, “This side up”, “Fragile”.

Storage

• Clean the device before storing. Follow the cleaning instructions in chapter 6.1.1. Basic Cleaning Instructions on page 13.
• Store the device in the original packaging, if possible.

Disposal

• Correct disposal of this product
• Waste Electrical and Electronic Equipment
• This symbol on the product, its packaging or documents indicates that the product shall not be treated as household waste. Dispose of this product by handing it to the respective collection point for recycling of electrical and electronic equipment. This is to avoid environmental damage or personal injury due to uncontrolled waste disposal.  For more detailed information about recycling of this product contact thelocal authorities or the authorized dealer.

Approval

Check the respective product page on the website of Highlite International (www.highlite.com) for an available declaration of conformity.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>