ARTECTA Ribbon Series Strip Light User Manual
- June 3, 2024
- ARTECTA
Table of Contents
ARTECTA Ribbon Series Strip LightV
Product Description
The Ribbon Series are IP20 LED strips for indoor installation at dry places.
They are suitable for mounting in an aluminum prole. The Ribbon Series are
available in various color temperatures and as RGB, RGBW and RGBA options.
For complete product specifications visit the respective product page on our
website www.highlite.com.
Safety Instructions
Important
Read and follow the instructions in this user manual before installing,
operating or servicing this product.
DANGER
Installation, service and maintenance of this product . shall be carried out
only by quailed persons.
This product must be installed in accordance with the applicable national and
international standards for electrical installations.
Improper installation may lead to hazardous situations and material damage.
Installation Site Requirements
Attention
The LED strips are suitable for installation only in dry locations. Not
suitable for outdoor installation.
It is recommended to install the LED strips in an aluminum prole.
An aluminum prole provides good heat dissipation\
Do not install the LED strips:
- in wet locations
- at a place where the LED chips are exposed to direct sunlight near heat-generating devices.
- Do not install the LED strips in environments with highly volatile substances, such as sulfur, chlorine, bromine and VOC. This will reduce the life of the LED chips.
Do not install the LED strips in environments with highly volatile substances, such as sulfur, chlorine, bromine and VOC. This will reduce the life of the LED chips.
Make sure that the LED strips are installed at a place with:
- ambient temperature between -20 °C and 50 °C
- sufficient arrow.
Make sure that the mounting surface is clean and smooth, and free of grease or
silicone oil.
Make sure that the mounting surface is thermally conductive and provides good
heat dissipation.
If the LED strips are mounted on a metallic surface, make sure that the soldering points are insulated. If the soldering points are not insulated, short-circuit may occur.
©2021 Artecta. All rights reserved.
No part of this document may be copied, published or otherwise reproduced
without the prior written consent of High lite International.
Design and product speciation’s are subject to change without prior notice.
For the latest version of this document and other language versions, please
visit our website www.highlite.com or contact us at
service@highlite.com.
Handling
-
Do not connect the LED strip to electrical power supply when the LED strip is on the reel or when it is tightly coiled. This will damage the LEDs.
-
Do not put excessive pressure on the LED chips.
-
You can bend the LED strip only along the vertical axis. The minimum bending radius is 20 mm.
-
Do not bend the LED strip with the LEDs on the inside.
-
Do not bend the LED strip on the horizontal plane.
-
Do not twist the LED strip.
-
Do not fold or break the LED strips.
-
Do not cover the LED strips with any material during operation.
Installation
WARNING
Incorrect installation can cause serious injuries and damage of property.
The installation of this product shall be carried out only by qualied persons.
Disconnect the power supply in the area where the product will be installed.
Use a compatible constant voltage driver to connect the LED strip to the
mains.
To connect the LED strip to the controller/driver or to other LED strips use
wires with sufficient cross-sectional area and current carrying capacity.
-
Determine the location of all components.
-
Cut the LED strip at the required length.
Cut the LED strip only at the marked cut line in the center of the solder pads. Make sure that the cut is made at 90°. The cutting tolerance is ±0.65 mm.
Do not cut the LED strip at any other place. This will damage the internal circuit and the LEDs will not work. -
Connect the LED strips if multiple LED strips are used.
Do not solder for a period longer than 3 seconds. Make sure that the soldering temperature is lower than 350 °C.
Make sure that the polarity is correct when connecting multiple LED strips. -
Remove the protective tape from the LED strip. Be careful not to cause damage to the electronic components.
-
Attach the LED strip to the mounting surface or to the aluminum prole.
Fold the LED strip at the marked cut line to mount the LED strip at a corner. Do not fold the LED strip more than once!
You can also solder wires between 2 LED strips at a corner. -
Connect the LED strip to the controller/driver. Make sure that the polarity is correct.
Setup example:
Troubleshooting
-
Change in brightness or color temperature of the LEDs
Make sure that the run is not too long.
Voltage drop can cause the LEDs’
brightness to decrease. -
Some LEDs do not work
Make sure that all connections are correct.
Make sure that the LED strip is not sharply bent.
This can cause components to detach from the circuit board. -
The LEDs are flickering
Make sure that the driver/power supply is compatible.
Make sure that all connections are correct.
Maintenance
Attention
Do not use detergent and/or water to clean this product.
This product is maintenance-free.
Use dry compressed air to clean the LED strip if necessary.
Do not use alcohol, solvents, detergents and/or water. This will damage the
LED strip.
Disposal
Dispose of this product by handing it to the respective collection point for recycling of electrical and electronic equipment. Do not dispose of with the household waste.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>