Wave 17665XX Rome Hot Tub water spa Installation Guide
- June 5, 2024
- wave
Table of Contents
Wave 17665XX Rome Hot Tub water spa Installation
WARNINC
READ ALL INSTRUCTIONS AND SAFETY WARNINGS IN THIS MANUAL Failure to follow the warnings and instructions in this manual may result in serious injury, drowning or electric shock. The safety of children is left in the hands of the customer. Children aged 5 and below are at the most risk. Always comply with the following instructions:
- Children should be under close and constant supervision
- Always designate a responsible person to mange pool and pool area
- For all users and children, wet the nape of the neck, chest and legs before entering the water
- Learn safety especially when specific to guidelines
- Prohibit diving and jumping
- Prohibit running, splashing games around the pool
- Ensure no unattended children, who cannot swim, use the pool without a life jacket
- Always keep the water treatment products out of reach of all children
If incident occurs remove the injured person or child from the pool and pool
area Contact emergency services for advice and guidance on how to treat
injured per-son or child
The hot tub’s electrical connections must be installed in the electrical
safety zones labelled 1, 2 or outside all safety zones. The measured zones are
limited by walls and fixed partitions.
For your own safety and that of your product, Ensure you follow the safety precautions outlined below. Failure to follow the instruction may result in serious injury, property damage or death. Improper installation or operation will void the warranty. Read, understand and follow all instructions:
DANGER
- Extreme caution must be exercised to prevent unauthorized access by children.
- Inspect the spa cover regularly for leak, premature wear and tear, damage or signs of deterioration. Never use a worn or damaged cover: it will not provide the level of protection required to prevent unsuper-vised access to the spa by a child.
- Always lock the spa cover after each use.
Risk of injury:
If the supply cord is damaged, it must be replaced by the manufacturer, its
service agent or similarly quali-fied persons in order to avoid a hazard.
Risk of Electric Shock:
- Do not permit any electrical appliances, such as a light, telephone, radio or television within 1.5m (5 feet) of a spa tub.
- Do not use the spa when it is raining, thundering or lightning ..
WARNING
-
To reduce the risk of electric shock, do not use an extension cord, timers, plug adapters or converter plugs to connect the unit to electric supply; provide a properly located outlet.
-
The spa electrical appliance should be supplied through a residual current device (RCD) having a rated residual operating current not exceeding 1 0mA.
-
Parts containing live parts, except parts supplied with safety extra-low voltage not exceeding 12V, must be inaccessible to occupants in the spa.
-
Parts incorporating electrical components, except remote control devices, must be located or fixed so that they cannot fall into the spa.
-
Residential electrical connection box must be located safely with a distance of at least 2m away from the spa.
-
Electric installation should fulfill the local requirement or standards.
-
This appliance can be used by children aged from 8 years and above and persons with reduced physi-cal, sensory or mental capabilities or lack of experience and knowledge if they have been given supervi-sion or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
-
To reduce the risk or injury, Children are not permitted to use this product unless they are closely.
-
Make sure the floor is capable of supporting the expected load ( 500kg/m2).
-
Adequate draining system must be provided around the spa to deal with overflow water.
-
To avoid damage do not leave the appliance empty for an extended period.
-
To avoid damage to the pump, the spa must never be operated unless the spa is filled with water.
-
Immediately leave spa if uncomfortable or sleepy.
-
To reduce the risk of injury :
-
Since excessive water temperatures have a high potential for causing fetal damage during the early months of pregnancy, pregnant or possibly pregnant women should limit spa water temperatures to 38° C (100° F).
-
Before entering a spa or hot tub the user should measure the water temperature with an accurate thermometer since the tolerance of water temperature regulating devices varies.
-
The use of alcohol, drugs or medication before or during spa use may lead to unconsciousness with the possibility of drowning.
-
The use of alcohol, drugs, or medication can greatly increase the risk of fatal hyperthermia in spas.
The causes and symptoms of hyperthermia may be described as follows: Hyperthermia occurs when the internal temperature of body reaches a level several degrees above the normal body temperature 37° C (98.6° F). The symptoms of hyperthermia include an increase in the internal temperature of body, dizziness, lethargy, drowsiness, and fainting. The effect of hyperemia include failure to perceive heat; failure to recognize the need to exit spa; unawareness of impending hazard; fetal damage in pregnant women; physical inability to exit the spa; and unconsciousness resulting in the danger of drowning. -
Obese persons or persons with a history of heart disease, low or high blood pressure, circulatory system problem, or diabetes should consult a physician before using a spa.
-
People with infectious disease should not use a spa or hot tub.
-
To avoid injury exercise care when entering or existing the spa or hot tub.
-
Water temperature in excess of 40° C (104° F) may be harmful to your health.
-
Never use a spa or hot tub alone or allow others to use the spa alone.
-
Do not use a spa or hot tub immediately following strenuous exercise.
-
Do not put the spa under 0° C (32° F) environment in order to avoid freezing if there is still water in the pool.
-
Do not turn on the spa when the water is frozen.
-
Never pour water with a temperature higher than 40° C(104° F) into the spa directly.
-
Always unplug this product from the electrical outlet before removing, cleaning, servicing or making any adjustment to the product.
-
Never jump or dive into a spa or any shallow body of water.
-
Do not bury the electrical cord. Locate the cord where it will not be damaged by lawn mowers, hedge trimmers and other equipment.
-
Do not attempt to plug in or unplug this product while standing in water or when your hands are wet.
-
Do not use the spa if damaged in delivery and/or malfunctioning in any way.
-
Keep all pets away from the spa to avoid any damage.
-
Do not add bath oil or bath salt to the spa water.
-
Do not leave an empty pool outside.
-
To prevent resetting of the thermal cut out, this appliance must not be supplied through an external swit-ching device, such as a timer, or connected to a circuit that is regularly switched on and off by the utility provider.
SPECIFICATIONS
–| | ****
5 persons
| –
---|---|---|---
Model
| ****
17665XX
Capacity| 5 persons
Dimension (outer)
| ****
67.7″ X 27.6″
172 x 70 cm
Dimensions (inner)
| ****
60′ X 27.6″
152 x 70cm
Water level Max| 40cm
Water capacity
Power supply
| | ****
940 L
–
220-240 V,50 Hz,1540W
Max heat temperature| 40′ C
Test certificate
| ****
CE
| ****
Heating efficiency
Ambien t t emp e ratu r e : 20°c
| | ****
1.5 – 2.5′ C/h
|
| | –| | –
PACKACE LIST
Ensure to check all parts are present:
INSTALLATION
Site selection
WARNING : Before proceeding to install your spa, please ensure that the allocated location meets the following conditions
- A level place in order to avoid any defect, hernia or leakage.
- Wide enough to support the pool and its pump unit.
- Able to support more than 500 kg/m2
- Sheltered from the sun and bad weather.
- Clean and free from sharp objects.
- Devoid of aggressive vegetation on the ground.
Failure to comply with these rules may result in property damage or personal injury .
Grounding
You are recommended to use the services of a qualified electrician to ensure
that the spa is electrically grounded by using a copper conductor of at least
2.5 mm2 cross section.
Assembling
USACE
Control panel
Functions
- Once powered-up, the LED displays the current water temperature automatically.
- The temperature units selector changes the temperature units from Celsius de-grees to Fahrenheit degrees.
- Press the temperature adjustment buttons, then the screen will flash. When it is flashing, you can set the desired temperature. The value will increase or decrease 1 degree at once. The temperature could be set between 30° C to 40° C (86° F to 104 ° F).
- To lock or unlock the control panel, press the Lock button and hold 3 seconds. Lock the control panel when you are away to prevent other people changing the settings.
- Press the massage button to activate the bubble massage system, the green indicator light turns on. It can be turned off by pressing it again.
Note:
- The massage system will stop automatically after 30 minutes of operation. Re-activate the mas-sage function by pressing the massage button again.
- When filter button is on, pressing bubble button will exchange filter mode into massage mode: filter indicator light will turn off and massage indicator light turn on. If press the bubble button again, the massage mode will be changed back to filter mode.
Note:
- With the heating system starting, the filtration system will commence working together.
- After turning off the heating system, the filtration system will still work.
- If the massage function is active, the filtration and heating functions cannot be activated.
Pool cover and security
After each use, the control panel must be locked and the pool must be coated
with its top cover and it must be attached to the base protector with the
safety buckles. Each safety buckles has a lock system ; closed buckle, the
latch in up position locks the buckle, the latch in down position unlocks the
buckle. The top cover keeps the heat from the water and secures the pool.
MAINTENANCE
Water maintenance
WARNING : A bad pool water quality can harm your health. Depending on the frequency and conditions of use:
- The filter cartridge should be regularly cleaned (150 hours max.).
- The filter cartridge should be replaced every 1 to 2 month.
- The pool water should be changed every 15 to 30 days.
Use a water test kit to control the parameters of the water before using the spa, or at least once a week. Use disinfection products for the spa. The treatment products should be used with caution and it is imperative to refer to instructions before use. Improper use may result in damage to the equipment. Damage resulting from improper use of treatment products is not covered by warranty (overdose, shock treatment,
Water balance
The water balance (pH) must be maintained between 7 and 7.4.
Water Sanitation
To sanitize the pool water, we suggest using an active oxygen-based treatment
or bromine placed in a floating dispenser. (Dispenser sold separately).
Cleaning and replacing filter cartridge
Dirty filter cartridge may contaminate the pool water and cause damage to the
heating function.
- Unscrew the filter case by turning it counter-clockwise. Take out the filter cartridge from the case.
- Rinse off the filter cartridge with a garden hose. If the filter cartridge remains dirty and discoloured, the filter cartridge should be replaced.
- Put back the cleaned filter cartridge into his case and screw it to the pool.
Water Sanitation:
To sanitize the pool water, we suggest using an active oxygen-based treatment
or bro-mine placed in a floating dispenser. (Dispenser sold separately) If
water is heavily polluted you should not use pool. Clean pool with with
specialist UV lighting equipment. mSeek professional advice and guidance
before doing this, considering the above.
Attention:
Detergent residues and dissolved solids from bathing suits and chemicals may
build up on the spa walls, Use soap and water to clean the walls and rinse
thoroughly with a garden hose using a direct powerful waterspray
Drainage
- Check the stopper on the bottom of the pool and the drain cap.
- Unscrew the drain cap.
- Remove the stopper on the bottom of the pool. Completely drain all water from the spa pool.
- Once empty, the pool can be cleaned with soap and water.
Storage
- Press the bubbling button to blow out the water inside the jet holes. Unplug the pump, remove the filter cartridge from the inner wall of the pool.
- Use a towel to wipe off the pool, dry for 24 hours
- Push the valves to deflate the pool.
- Fold the pool.
It is recommended that you store the SPA in its original package in a warm dry place.
Repair kit
Small punctures or holes in the pool liner can be repaired with the repair kit
included.
- Find the leak.
- Thoroughly clean the area surrounding the leak.
- Cut a piece of repair material in round shape, which should be larger than the damaged area.
- Apply adhesive to the underneath side of the patch and around the area to be repaired.
- Put the patch on the damaged area and press down firmly. Allow 12 hours for repair to dry. After patch has dried, apply glue around the edges for a complete seal (dry 4 hours).
TROUBLESHOOTING
If air valve damages or leaks, please replace valve according to the steps followed.
Here are some useful tips to help you to diagnose and rectify common sources of trouble.
Problem
f–
|
Cause
| –
Solution
–
Power failure
| –
–
|
---|---|---|---|---
Control panel screen does not operate|
Check power source
| Reset the RCD plug / Check if the wiring system is adapted to ower of the QUmQ unit (1540W ) –
Call for service if it does not reset
|
SPA pump does not heat properly
| Temperature set is too low| Set to a higher temperature|
Filter Cartridge is dirty| Clean or Replace the cartridge (see chapter 5.2)|
ow water level
Heating element defective
| Fill water to minimum water level
Call for service
|
–
| |
Bubble massage system does not
|
Pump is overheating
‘–
Auto shut-down feature (30min) is
activated
|
Cut off the power and wait until the pump has cooled.
‘–
Press the bubble button to reactivate
|
–
| |
work|
|
Call for service if it does not reset
f–
Clean or Replace the cartridge (see chapter 5.2)
|
–
| |
| Malfunction of the pump unit|
f–| |
| Filter Cartridge is dirty|
Water filtration does not work|
Inlet and outlet blocked
/¼insidethe numn
|
Clean the inlet and outlet
f–
Fill water to minimum water level
|
–
| |
f–
| Malfunction of the pump unit| –| , Call for service if it does not reset| |
|
|
| Adaptor seal improperly| | Replace the seal in the right position|
Pump leakage| | |
| Water leakage from pump body| Check the pump body, call for service|
Spa pool leakage
|
Spa pool is tom or punctured
|
Use provided repair kit (see chapter 5.4)
|
Water is not clean
–
| Insufficient filtering time| Increase the filtering time|
Filter Cartridge is dirty| Clean or Replace the cartridge (see chapter 5.2)|
Pool filled water quality| Change the pool water completely|
_!mproper water treatment| Refer to the chemical manufacturer ‘s instructions
–
| |
–
|
Error code
If the screen displays an error code “Ex”, please refer to the table below.
- Check that the water line is between the high and low limits.
- Clean or replace the filter carbidge
- Unscrew and clean the 2 nozzles (Entry and exit of water) inside the spa and remove wastes if necessary (leaves, hairs, fur, skin … )
- Check that the propeller of the filter pump does not contain foreign objects. Cut the spa again electrically for 5 minutes and re-connect it, if the error code is still displayed on the control box please contact the service centre
Warranty
Wave products have been inspected with no evident defects prior to leaving the
factory. Wave warrants this product against defects in material and
workmanship for a period of time, 1 year for the pump and 6 months for the
liner.unless local law has special requirement. Warranty for this product
begins on the date of purchase and Wave requires presentation of the original
proof to purchase to confirm the date. During the warranty period, Wave will
either repair or replace, at its discretion, any defective products.
Replacement products or repaired parts will be warranted for the unexpired
portion of the original warranty. Shipping cost policy The return of defect
parts to the authorized service centre is at the cost of the owner. On
warranty period, the return is at the cost of service center. Warranty policy
This limited warranty does not apply to any defect resulting from negligence,
accident, misuse, or other reason beyond Wave’s control, included but not
limited to: normal wear and tear, negligence or failure to follow the product
instructions, improper or inadequate maintenance; connection to improper power
supply; chemical water damage, loss of pool water, unauthorized product
modification or repair; use for commercial purpose; fire, lightening, flood or
other external causes.
This warranty is valid only in the country of purchase in such countries where Wave sells and services the same model with identical technical specifications. Warranty service outside the country of purchase is limited to the terms and conditions of the corresponding warranty in the country of service. Where the cost of repairs or replacement is not covered by this warranty, Wave will advise the owners and the cost shall be charged to the owner. This warranty only applies to the original purchaser and terminates upon any transfer of ownership. All repairs of which warranty claims are made must be pre-authorized by a Wave service centre. All the authorized selling dealer is responsible for all in-field service work carried out on your Wave product. Wave will not be liable for results of cost of workmanship from unauthorized service person.
Warranty registration
To validate your warranty, please register your product on our website
Wave:www.wavespas.com It is essential that all
informations including customer name, date of purchase, serial number, spa
model are provided. Without this information the warranty will be invalid.
Waves Direct
9-10 Charlotte Square , Newcastle upon Tyne, Tyne and Wear, NE1 4FX, United
Kingdom wavespas.com