Smart Wave B01-004 Rodent Trap with BLE and LoRa User Manual
- October 30, 2023
- Smart Wave
Table of Contents
B01-004
User Manual
Revision 1.1
B01-004 Rodent Trap with BLE and LoRa
NOTICE TO READERS
This document contains proprietary information which is the property of
SMART WAVE TECHNOLOGIES CORP.
CONFIDENTIAL
Except for the right expressly granted in writing, this document may not, in
whole or in part, be duplicated or disclosed without the prior written
permission of Smart Wave Technologies Corp.
PRODUCT DESCRIPTION
The B01‐004 is a bait station data capture device used to detect rodents and insects that have entered the bait station and timestamp when the event occurred. The device uses a capacitive touch pad connected to capacitive touch sensor IC configured with customized filtering to provide information to the controller, which in turn uses a proprietary filtering algorithm to isolate events and detections. This information is passed to a mobile phone app, via Bluetooth, which will upload the information to a cloud server. The device is also equipped with LoRaWAN capabilities to provide direct device‐to‐cloud connection through a configurable heartbeat interval.
PRODUCT INSTALLATION
The B01‐004 is installed in a plastic housing and sonically welded to provide complete protection from the various installation environments and rodents. A ER14505H battery must be connected to the B10‐004 before installation into plastic housing
PRODUCT OPERATION
Once powered, the device will advertise for 30 seconds before going to sleep.
Tapping the sensor pad a few times will wake the device up and it will again
advertise for 30 seconds before going back to sleep. This operation will
happen for device that are unregistered (Factory Mode).
For devices that are registered and installed in the field, the device will
continually advertise every 1.5 seconds. A LoRaWAN heartbeat will also
transmit periodically according to how the device is configured.
REGULATORY INFORMATION
CANADA
ISED Regulatory Statements
IC: 24934‐B01004
ISED non‐interference disclaimer
This device contains license‐exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada’s license‐exempt
RSS(s). Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
RF Exposure statement
This equipment complies with ISED RSS‐102 radiation exposure limits set forth
for an uncontrolled environment. This equipment should be installed and
operated with minimum distance 20 cm (7.9 inches) between the radiator and
any part of your body. This transmitter must not be co‐located or operating in
conjunction with any other antenna or transmitter.
CAN ICES‐3 (B)/NMB‐3(B)
Regulatory information in the App can be accessed from the main screen
(Dashboard) by performing the following steps:
- Access the Site Menu (upper left corner of the App screen)
- Select “About Us” from the Site Menu
- Tap the button labeled “Regulatory”
USA
FCC Regulator Statements
FCC: 2ASYW‐B01004
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate this equipment.
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation. Please note that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
RF Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This transmitter must not be co‐located or operating
in conjunction with any other antenna or transmitter. In order to avoid the
possibility of exceeding the FCC radio frequency exposure limits, this
equipment should be installed and operated with minimum distance 20 cm (7.9
inches) between the antenna and your body during normal operation. Users must
follow the specific operating instructions for satisfying RF exposure
compliance.
NOTICE:
End user must include the following on the label of the end product
FCC ID: 2ASYW‐B01004
IC: 24934‐B01004
This is the Last Page of this Document
B01-004 User Manual Rev1.1
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>