Miele EPI7684 Wireless Food Probe System User Manual
- June 5, 2024
- Miele
Table of Contents
Miele EPI7684 Wireless Food Probe System
General
The wireless food probe system consists of the radio module (EPI7684), antenna system and the wireless food probe. This system enables the roasting process of the food to be monitored simple and reliably. The wireless food probe will be here not described because it is a passive device and does not matter for the installation of the system.
The wireless food probe system may be installed in the Miele domestic appliances like ovens or steam cooker (host devices)
Integration instruction
The EPI7684 and the loop antenna must be integrated under consideration of the
technical data. It is not allowed to make any changes on the module or use
another antenna.
Technical data EPI7684 and antenna
| VCC in V | 13,0 and 3,3 DC |
|---|---|
| Current in mA | 170 max. |
| Ambient temperature in °C | 0-85 |
| Humidity max | 90% Non condensation |
| Dimensions in mm | 105×80 |
| Wireless | |
| Antenna type | external loop antenna |
| Antenna gain | -7dBi |
| Frequency band | 2400 MHz – 2483.5 MHz |
| Method of transmitting radio signal | FHSS |
| Channels | 600 |
| Transmission Power in mW | <100 |
Interface to the control-/ power electronic of the host device
On the control-/ power electronic is a 4-pin rast 2.5 plug and on the EPI site
is 8-pin rast 2.5 plug. This connection includes communication and power
supply wire (13 and 3,3V DC)
Norms / Standards
FCC / IC
FCC regulation:
FCC 47 CFR
Part 15.247
Part 1.1310
Part 1.1091
IC regulation:
RSS-247, Issue 2
RSS-Gen, Issue 5
RSS-102, Issue 5
Compliance Statement and Integration
In accordance with FCC 47 CFR Part 15 and RSS-247, Issue 2, the EPI7684 (FCC ID: SSVNAEPI03; IC: 5669B-EPINA03) is listed as a Modular Transmitter Device.
Notice:
This device complies with Part 15 of the FCC Rules and contains licence-exempt
transmitter(s)/receiver(s) that comply with Innovation, Science and Economic
Development Canada’s licence-exempt RSS Standarrd(s). Operation is subject to
the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
Radiofrequency radiation exposure Information:
This equipment complies with FCC radiation exposure limits set forth and Canada radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
CAUTION:
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
USERS MANUAL OF THE END PRODUCT:
The end user has to be informed that any changes or modifications not
expressly approved by the manufacturer could void the user’s authority to
operate this equipment. The following statements are required to be available
in the user’s manual: This device complies with Part 15 of the FCC Rules and
contains licence-exempt transmitter(s)/receiver(s) that comply with
Innovation, Science and Economic Development Canada’s licence-exempt RSS
Standarrd(s). Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired
operation.
Radiofrequency radiation exposure Information:
This equipment complies with FCC radiation exposure limits set forth and
Canada radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance of 20 cm
between the radiator and your body. This transmitter must not be co-located or
operating in conjunction with any other antenna or transmitter.
LABEL OF THE END PRODUCT:
The final end product must be labeled in a visible area with the following
“Contains FCC ID: SSVNAEPI03; Contains IC: 5669B-EPINA03”. The following
statement has to also be available on the label:
This device complies with Part 15 of the FCC Rules and contains licence-exempt
transmitter(s)/receiver(s) that comply with Innovation, Science and Economic
Development Canada’s licence-exempt RSS Standarrd(s). Operation is subject to
the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
Integration
This EPI7684 Module will only be integrated on our responsibility into Miele appliances/endproducts.
The host manufacturer is responsible for additional testing to verify compliance as a composite system. When testing the host device for compliance with the Part 15 Subpart B requirements, the host manufacturer is required to show compliance with the Part 15 Subpart B while the transmitter module(s) are installed and operating. The modules should be transmitting and the evaluation should confirm that the module’s intentional emissions are compliant (i.e. fundamental and out of band emissions) with the Radio essential requirements. The host manufacturer must verify that there are no additional unintentional emissions other than what is permitted in the Part 15 Subpart B or emissions are complaint with the Radio aspect
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>