NIIMBOT B3S Smart Label Printer User Guide
- June 3, 2024
- NIIMBOT
Table of Contents
NIIMBOT B3S Smart Label Printer
Package Contents
Installation
-
Tear off the seal on the label paper.
-
Press down the Paper Compartment Open Button to open the paper compartment.
-
Toggle the spindle to the “open” position as the arrow sign indicates.
-
Slide the paper compartment baffle to the correct scale according to the width of the paper roll and toggle the spindle towards the blade.
After adjusting the paper compartment scale, the spindle must be securely toggled to prevent any misaligned printing. -
Fit the paper roll into the paper compartment and make sure the print side faces the print head. Pull a certain length of paper out from the paper exit and then close the paper compartment cover.
Distinguish the sides of the paper roll. It will not print if the paper roll is reversed.
Basic Functions and Settings
-
Power On
-
Feeding Paper
Press the Paper Exit/OK button and the device will roll out one stretch of paper. -
Choosing Paper Types: Different Types of Paper Displayed Accordingly
- Crack Label: The seam of paper should be aligned to the cutting opening, tear the paper to have it cut by the blade.
- Black Label: Tear the paper through the tear line without using the blade.
- Cont Labe: A full sheet of print paper and use the blade to have it cut at any position.
- TRN Label: A type of transparent cont label; the seam of paper should be aligned to the cutting opening, tear the paper to have it cut by the blade.
-
Lack of Paper/Open Compartment
If the monitor screen displays information of Cover Open/Lack of Paper, the device will not respond to printing commands. -
Low Battery
When the device is out of power, the monitor screen will display “The battery level is low. Please charge!” and will automatically power off in 10 seconds. -
Bluetooth Connection
When the Bluetooth is connected, the Bluetooth icon will be displayed in inverted white. -
Power Indicator
When the device is connected with a power adapter, the power icon will be displayed as follows. **** -
Settings
Press Power/Settings button at the home interface to enter the settings interface; continue to press the Power/Settings button to switch among 5 different setting interfaces, including “Density”/ ”Type of Paper”/”Shutdown Time”/”Language”/”Self-check page”. Press Paper Exit/OK button at the setting interface. -
Printing density includes 5 levels (1/2/3/4/5).
-
Type of paper includes four types (crack label/black label/cont label/TRN label).
-
The shutdown time when no operation is performed on the device is set in 4 levels (15 minutes/30 minutes/60minutes/never).
-
Language is available in 2 types (Chinese/English).
-
Press the “Paper Exit/OK” button to print the self-check page. The self-check page will include information of printer model, firmware version, hardware version, device serial number, etc.
-
Printing
During the printing process, the monitor screen will display “Printing”, and will automatically return to the home interface when the printing is completed. You can pause the printing with the phone APP or press the “Paper Exit/OK” button.
Installing App **
**
- Before using the printer, please install the NIIMBOT app from Google Play or the App Store.
More information available on the NIIMBOT app.
- Get the NIIM app for more label designs for homes.
Connecting and Printing
-
Open NIIMBOT app and turn on Bluetooth on your phone.
-
On Home, tap Connect smart label printer. Then select device model.
Notice: If a PIN code is required, input 0000 or 1234. -
After connecting, tap on “Current label template” on the Home tab to enter the label editor.
Special Notes
Images of products, accessories, and the app in this manual are for
illustrative purposes only and may be different from actual products. Products
are subject to change without prior notice.
Basic Functions
Function
| ****
Operation
---|---
Switch on
| ****
Hold down the Power button for three seconds.
Switch off
| Hold down the Power button for three seconds when the device is on.
Print history
| ****
Press the right button while the device is powered on.
Print a test page
| While the device is powered on, press the left button to switch to “Print Self-check Page” interface; press the right button to print the self-check page.
Specifications
Product
| ****
Label Printer
| ****
Model
| ****
NIIMBOT B3S
---|---|---|---
Dimensions
| ****
115.5109.6758.58mm
| ****
Weight
| ****
317g
Charging Time
| ****
5 – 6 hours
| ****
Input
| ****
5V DC, 1A
Battery
Capacity
| ****
2000mAh
| Printing Method| ****
Thermal printing
Printing Resolution| ****
203dpi
| Printing Width| ****
25-75mm
Connectivity
| ****
Bluetooth,Type-C
| ****
Charge
| ****
Type-C
Transmit Power
| ****
4dBm(Maximum)
| Operating Temperature| ****
5℃ – 40℃
Safety Precautions
Please read all the instructions and warnings in this manual carefully before using this product to ensure the proper functioning of the device and your safety.
Warnings
- Please keep the product and accessories out of the reach of children or they must be used under the supervision and guidance of a guardian;
- Turn off the power immediately when water gets into the product;
- Turn off the power immediately in case of any product malfunction;
- If you want to use a power adapter, always use one that is safe, regulatory-compliant, and compatible;
- Do not disassemble the product to replace the battery. Improper operation may cause an explosion;
- The battery contains special protection circuit and device, please do not disassemble the battery without authorization, otherwise it may cause a short circuit or leakage. If electrolyte gets into your eyes, flush with water immediately and seek medical help;
- Do not expose the product and the power adapter to high temperature or high humidity. Do not put them in water, otherwise a short circuit may occur and the battery may heat up, smoke, deform, damage, or even explode;
- If smoke or smell comes from the product or the power adapter, please unplug the power adapter immediately and avoid any burns.
FCC Statement
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception,which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirement.The device can be used in portable exposure condition without restriction.
Declaration of conformity
Hereby, Wuhan Jingchen Intelligent Identifification Technology Co., Ltd.
declares that this device is in compliance with the essential requirements and
other relevant provisions of Radio Equipment Directive (RED) 2014/53/EU. This
product can be used across EU member states. This device can be used in
European Union.
Hereby, [Wuhan Jingchen Intelligent Identifification Technology Co., Ltd.]
declares that the radio equipment type [NIIMBOT D11] is in compliance with
Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the
following internet address:http://www.niimbot.com.
Canadian Statement
This device contains licence-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada’s licence-exempt
RSS(s). Operation is subject to the following two conditions:
- (1) This device may not cause interference.
- (2) This device must accept any interference, including interference that may cause undesired operation of the device.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>