NIIMBOT D101 Smart Label Printer User Guide
- June 4, 2024
- NIIMBOT
Table of Contents
Smart Label Printer
Quick Start Guide
NIIMBOT D101
Package Contents
Installation
-
Swipe left on the slider to open the lid.
-
Remove or keep the baffle according to the width of the label paper.
About the baffle: Insert the label paper directly if your label paper is not wider than 15mm. If its width is 15mm-27mm, remove the baffle before installing. -
After confirming the width, install it against the right side of the paper compartment, with the print side facing down.
-
Close the lid. Long-press the power button and the printer will be ready for use.
Installing App
-
Before using the printer, please install the NIIMBOT app from Google Play or the App Store.
More information is available on the NIIMBOT app.
-
Get the NIIM app for more label designs for homes.
Connecting and Printing
-
Open the NIIMBOT app and turn on Bluetooth on your phone.
-
On Home, tap Connect smart label printer. Then select the device model.
Notice: If a PIN code is required, input 0000 or 1234. -
After connecting, tap on “Current label template” on the Home tab to enter the label editor.
Special Notes
Images of products, accessories and the app in this manual are for
illustrative purposes only and may be different from actual products. Products
are subject to change without prior notice.
Basic Functions
| Function | Operation |
|---|---|
| Switch on | Hold down the Power button for three seconds. |
| Switch off | Hold down the Power button for three seconds when |
the device is on.
Print history| Press the Power button once when the device is on.
Print a test page| Double-press the Power button when the device is on.
LED Indicators
| Indicator | Status | Description |
|---|---|---|
| Blue | Blinking slowly | Standby |
| Blue | Blinking fast | Charging |
| Blue | Solid | Bluetooth connected |
| Red | Blinking slowly | Battery low, standby |
| Red | Blinking fast | Battery low, charging |
| Red | Solid | Battery low, Bluetooth connected |
Specifications
| Product | Label Printer | Model | AIMBOT D101 |
|---|---|---|---|
| Dimensions | 13080.247mm | Weight | 340g |
| Charging Time | 3 – 4 hours | Input | 5V DC, 1A |
| Battery Capacity | 1500mAh | Printing Method | Thermal printing |
| Printing Resolution | 203dpi | Printing Width | 24mm |
| Connectivity | Bluetooth | Charge | Type-C |
| Transmit Power | 4dBm(Maximum) | Operating Temperature | 5~40℃ |
Safety Precautions
Please read all the instructions and warnings in this manual carefully before using this product to ensure the proper functioning of the device and your safety.
*Warnings
| |
---|---|---
Don’t disassemble the product without authorization. Disassembled products
cannot
be returned or exchanged.| Do not wipe the product with corrosive chemicals or
cleaning agents.| Do not use the product near places with flammable products
such as gas stations
or fuel depots.
- Please keep the product and accessories out of the reach of children or they must be used under the supervision and guidance of a guardian;
- Turn off the power immediately when water gets into the product;
- Turn off the power immediately in case of any product malfunction;
- If you want to use a power adapter, always use one that is safe, regulatory-compliant, and compatible;
- Do not disassemble the product to replace the battery. Improper operation may cause an explosion;
- The battery contains special protection circuit and device, please do not disassemble the battery without authorization, otherwise, it may cause a short circuit or leakage. If electrolyte gets into your eyes, flush with water immediately and seek medical help;
- Do not expose the product and the power adapter to high temperatures or high humidity. Do not put them in water, otherwise, a short circuit may occur and the battery may heat up, smoke, deform, damage, or even explode;
- If smoke or smell comes from the product or the power adapter, please unplug the power adapter immediately and avoid any burns.
Related Statements
FCC Statement
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. Any changes or
modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet the general RF exposure requirements. The device can be used in portable exposure conditions without restriction.
Declaration of conformity
Hereby, Wuhan Jingchen Intelligent Identification Technology Co., Ltd.
declares that this device is in compliance with the essential requirements and
other relevant provisions of the Radio Equipment Directive (RED) 2014/53/EU.
This product can be used across EU member states. This device can be used in
European Union.
Hereby, [Wuhan Jingchen Intelligent Identification Technology Co., Ltd.]
declares that the radio equipment type [NIIMBOT D11] is in compliance with
Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the
following internet address:http://www.niimbot.com.
Canadian Statement
This device contains license-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science, and Economic Development Canada’s license-exempt
RSS(s). Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
Wuhan Jingchen Intelligent identification technology Co., Ltd.
Support Email: service@niimbot.com
Official Website: www.niimbot.net
Office Address: Creative Workshop No. 5, Creative World, Yezhihu West
Road, Hondshan District, Wuhan, China
Production Address : No. 1 Tianyang Road, Chuanlong Avenue, Hengdian
Street, Huangpi District, Wuhan, China
© 2022 NIIMBOT. All rights reserved.
NIIMBOT is a brand under Wuhan Jingchen Intelligent ldentification Technology
Ltd.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>