hama KVM-Switch Changeover Switch HDMI USB Instruction Manual

: June 3, 2024
: Hama

Table of Contents

Operating Instructions
**Package Contents
Startup and Operation
Technical Data
Documents / Resources

KVM-Switch Changeover Switch HDMI USB
Instruction Manual

Operating Instructions

hama KVM-Switch Changeover Switch HDMI USB - Fig |
---|---

**Package Contents

**

KVM switch
2 HDMI™ cables
2 USB cables
These operating instructions

Safety Notes

Do not attempt to service or repair the product yourself. Leave any and all service work to qualified experts.
Do not open the device or continue to operate it if it becomes damaged.
Do not operate the product outside the power limits given in the specifications.
Do not modify the product in any way. Doing so voids the warranty.
Keep this product, as all electrical products, out of the reach of children!Use the product for its intended purpose only.
Protect the product from dirt, moisture and overheating, and only use it in a dry environment.
The product is intended for indoor use only.
Do not use the product in the immediate vicinity of heaters or other heat sources or in direct sunlight.
Do not use the product in moist environments and avoid splashes.
Do not use the product in areas where the use of electronic devices is not permitted.
Do not drop the product and do not expose it to any major shocks.
Dispose of packaging material immediately according to locally applicable regulations.

Warning

Find out the maximum output current capacity of the USB port onyour device. To do this, consult the operating instructions or ask the manufacturer.
Common values are 500 mA for USB-A 2.0, 900 mA for USB-A 3.0, and up to 3000 mA for USB-C.
Ensure that the total power consumption of all USB devices connected to the KVM switch does not exceed the determined value.

Note

For optimised video function, we recommend passive monitor adapters/cables (without chipset/signal converter).

Startup and Operation

Connect the enclosed HDMI™/USB cable both to the KVM switch and PC/notebook 1 and PC/notebook 2. Now connect the HDMI™ cable on the monitor/TV to the KVM switch connection marked “Monitor/TV”.
The symbols printed underneath the USB sockets represent connection suggestions. The USB devices can however also be connected to the KVM switch in a different sequence / combination.
Switch on your computer and boot the system.
Connect the product to a free HDMI™/USB port on your computer.
You do not have to install drivers; the computer will automatically recognise the product.
If necessary, follow the instructions for your operating system.
In order to use your devices, plug them into the product one after the other.
The connected devices can be toggled between PC/notebook 1 and PC/ notebook 2 by pressing the “Select” button on the KVM switch.
The LED on the KVM switch lights up 1 or 2, depending on whether the connected devices are assigned to PC/notebook 1 or PC/notebook

Warranty Disclaimer
Hama GmbH & Co KG assumes no liability and provides no warranty for damage resulting from improper installation/mounting, improper use of the product or from ailure to observe the operating instructions and/or safety notes.

Technical Data

Operating voltage / current consumption	5 V max. 500 mA
Compatibility	USB-A port

HDMI™ port
System requirements| Windows 11 / 10 / 8 / 7
Mac OS 10.8 ≥
USB specification| USB 2.0

Note: If there is interference or the product no longer responds, unplug the product, wait a few seconds and then plug it in again.

All listed brand saretrademarks of the corresponding companies. Errors and omissions excepted, and subjecttotechnicalchanges.Our general terms of delivery an dpayment are applied.

Service &Support
www.hama.com
+499091502-0

Documents / Resources

| hama KVM-Switch Changeover Switch HDMI USB [pdf] Instruction Manual
KVM-Switch Changeover Switch HDMI USB, KVM-Switch, Changeover Switch HDMI USB, Changeover Switch, HDMI USB Changeover, Changeover
---|---