TOMADO TPM1501B Espresso Machine Instruction Manual
- June 5, 2024
- TOMADO
Table of Contents
TOMADO TPM1501B Espresso Machine
SAFETY INSTRUCTIONS
- Carefully read the entire instruction manual prior to using the appliance and store it carefully for future reference.
- Only use this appliance for the purposes described in the instruction manual. Caution! Avoid contact with the hot surfaces and/or steam! Caution! Avoid contact with metal parts, this could result in personal injury! Attention! Avoid making contact with the blades in the filter for coffee capsules, these are very sharp.
- Only connect the appliance to alternate current, to an earthed wall socket, with a mains voltage that corresponds with the information provided on the information plate of the appliance.
- Never bend the power cord sharply or allow it to run across hot parts.
- Fully unwind the cord to prevent it from overheating.
- Never place the appliance near appliances that give off heat, such as ovens, gas cookers, hotplates, etc. Keep the appliance away from walls or other objects that may catch fire, such as curtains, towels (cotton or paper, etc.).
- Always make sure the appliance is placed on an stable, flat and heat-resistant surface and is only used indoors at a temperature higher than 0 °C.
- Do not leave the appliance unsupervised if the appliance is operational.
- Do not use the appliance if the plug, cord or appliance are damaged, or if the appliance no longer functions properly or if it is damaged in any other way. If this is the case, consult the retailer or our maintenance service.
- If the connection cord of this appliance becomes damaged, it must be replaced by the manufacturer, its customer service or a similarly qualified person in order to prevent hazardous situations.
- Do not pull the cord and/or appliance to remove the plug from the wall socket.
- Never touch the appliance with wet or damp hands.
- Keep the appliance out of reach of children. Children do not see the dangers associated with handling electrical appliances. Therefore, never allow children to operate electrical appliances without supervision. Keep the appliance and cord out of reach of children younger than 8 years of age.
- The appliance may be used by children of 8 years and older and by persons with restricted physical, sensory or mental capacities or a lack of experience or knowledge, provided that they use the appliance under supervision and are instructed about the safe use of the appliance, and understand the associated hazards.
- Children must not play with the appliance.
- The appliance must not be cleaned or maintained by children, unless they are over 8 years of age and this is done under supervision.
- If the appliance is not being used or is being cleaned, switch off the appliance and remove the plug from the socket.
- Always make sure the appliance is switched off and cooled down and that the plug has been removed from the socket, before you remove parts from the appliance.
- If the appliance does not function after it has been switched on, it is possible that the fuse or earth leakage circuit breaker has been activated in the electrical distribution box. The load on the group can be too high or an earth leakage could have occurred.
- In case of a breakdown, never make repairs yourself; a tripped safety device in the appliance could indicate a defect that cannot be remedied by removing or replacing this safety device. Only original parts should be used.
- The water reservoir deforms when using hot water, therefore only fill it with cold water.
- Always use the coffee machine with a closed filter cover.
- Do not switch on the appliance with an empty reservoir.
- Never submerge the appliance, cord, or plug in water.
- This appliance is intended for household and similar use, such as:
- in staff kitchens, in shops, offices, and other work environments;
- by guests of hotels, motels, and other residential environments;
- in Bed&Breakfast type environments;
- farms.
- If the appliance is not used as intended, no compensation can be claimed in case of defects or accidents and the warranty will be invalidated.
PRODUCT DESCRIPTION
- Hot plate
- Operating panel
- Removable cup grille
- Floater
- Removable leak tray
- Steampipe
- Steampipe handle
- Attachment steam pipe
- Removable water reservoir
- Water hose
- One-cup filter
- Two-cup filter
- Filter holder
- Filter for coffee capsules
- Filter holder for coffee capsules
- Measuring spoon/tamper
OPERATING PANEL
- Steam button
- Coffee button
- On/off button
- Thermometer
- Steam controller
- Coffee indicator light,
- lights up when the correct
- the coffee temperature has been reached
- On/off indicator light,
- lights up when the appliance is switched on
- Steam indicator light,
- lights up when the correct
- the steam temperature has been reached
PRIOR TO FIRST USE
Before using the coffee machine for the first time, proceed as follows: Carefully unpack your coffee machine and remove all packaging material and possible promotional stickers. Keep the packaging (plastic bags and cardboard) out of reach of children. After unpacking the appliance, carefully check it for external damage that may have occurred during transport. Place the coffee machine on a flat, stable and heat-resistant surface. Check that the voltage stated on the information plate matches the voltage used in your region. It is best to clean the interior of the new coffee machine prior to using it for the first time. This is done as follows:
- Slide the removable water reservoir out of the appliance. Fill the water reservoir with cold drinking water. Do not fill it above the MAX mark. Slide the reservoir back into the appliance and place the water hose in the water reservoir.
- Place the one- or two-cup filter without coffee in the filter holder, making sure that the ball at the side of the filter falls precisely into the indentation in the holder. Then place the holder in the appliance from the INSERT position and firmly turnthe handle counter-clockwise to the LOCK position.
- Place a cup in the centre of the cup grille and make sure the steam controller is switched off (turned to 0).
- Insert the plug in the earthed wall socket and press the on/off button once ( ), after which the indicator light switches on.
- Now press the coffee button ( ), the appliance starts to pump water. When water flows out of the filter holder, you must press the coffee button ( ) once more to stop the low of water.
- Check that the steam button ( ) is not pressed down. When the button is not pressed down, the water will be heated up to the ideal temperature for making coffee. When the button is pressed down, the water will be heated up to the ideal temperature for creating steam, this temperature is higher than the temperature for making coffee.
- When the coffee indicator light lights up continuously, the water is at the correct temperature. Press down the coffee button( ) and the water will start to flow.
- Allow the water to flow for 1 minute and then press the coffee button ( ) once more to stop the flow of water. Make sure your cup is large enough to contain all the water. Then switch off the appliance, remove the plug from the socket and remove the remaining water from the water reservoir and the cup.
- Allow the appliance to cool down and clean all separate parts as indicated in section CLEANING AND MAINTENANCE. Attention: The appliance can make more noise when pumping water for the first time, this is normal, as the air in the appliance is released. After approximately 20 minutes the noise will decrease. Important: Only fill the appliance with cold water. Hot water has a negative effect on the coffee machine’s life span.
MAKING ESPRESSO/COFFEE
-
Slide the removable water reservoir out of the appliance. Fill the water reservoir with cold drinking water. Do not fill it above the MAX mark. Slide the reservoir back into the appliance and place the water hose in the water reservoir.
-
Take the filter holder from the appliance by turning it clockwise.
-
Fill the one- or two-cup filter with the required amount of coffee by means of the provided measuring spoon. Firmly compress the coffee using the tamper. Depending on your taste, approximately 1 cup of coffee can be made with 1 measuring spoon. When using coffee capsules for making coffee, you can place the capsules of your taste in the filter provided for that purpose. Attention! Avoid making contact with the blades in the filter for coffee capsules, these are very sharp.
-
Place the filter in the filter holder, making sure that the ball at the side of the filter falls precisely into the indentation in the holder. Then place the holder in the appliance from the INSERT position and firmly turn the handle counter-clockwise to the LOCK position.
-
Place the required number of coffee cups on the cup grille. Make sure the cups are properly positioned, so that the coffee flows into the cups.
-
Check that the steam controller is switched off (turned to 0). Insert the plug in an earthed wall socket and switch on the appliance by pressing the on/off button ( ), after which the indicator light switches on.
-
Check that the steam button ( ) is not pressed down. When the button is not pressed down, the water will be heated up to the ideal temperature for making coffee. When the button is pressed down, the water will be heated up to the ideal temperature for creating steam, this temperature is higher than the temperature for making coffee.
-
When the coffee indicator light lights up continuously, the water is at the correct temperature. Then press down the coffee button ( ) and coffee will start to flow. Press the coffee button once more when the required amount of coffee has been made. If you do not do this, the cup will overflow! Attention: When making coffee, the coffee indicator light may switch off occasionally, this is normal and happens because the appliance is continuously heating in order to maintain the correct temperature.
-
Coffee tastes best immediately after it has been made, so do not wait too long before serving.
Tips: -
We recommend slightly warming up an espresso cup prior to use, for instance by first placing it on the hot plate on top of the appliance. A pre-heated cup will prevent the espresso from cooling down too quickly.
-
In order to make a good espresso, we recommend pre-heating the appliance. This is done by first making a cup of espresso without adding coffee, as a result of which hot water flows through the appliance. Warning: Do not leave your coffee machine unsupervised when it is working, because of the manual actions you have to perform.
HEATING UP (CHOCOLATE) MILK
-
Slide the removable water reservoir out of the appliance. Fill the water reservoir with cold drinking water. Do not fill it above the MAX mark. Slide the reservoir back into the appliance and place the water hose in the water reservoir.
-
Place the one- or two-cup filter without coffee in the filter holder, making sure that the ball at the side of the filter falls precisely into the indentation in the holder. Then place the holder in the appliance from the INSERT position and firmly turn the handle counter-clockwise to the LOCK position.
-
Check that the steam controller is switched off (turned to 0). Insert the plug in an earthed wall socket and switch on the appliance by pressing the on/off button ( ), after which the indicator light switches on.
-
Press the steam button ( ). When the button is pressed down, the water will be heated up to the ideal temperature for creating steam, this temperature is higher than the temperature for making coffee. When the button is not pressed down, the water will be heated up to the ideal temperature for making coffee.
-
Fill a cup with the drink that you want to heat up, (chocolate) milk. It is important that the cup used is not too small, observe a minimum diameter of 7.5 mm and take into account that the drink can double in volume when foaming.
-
Remove the attachment from the steam pipe and place the steam pipe in the drink to be heated. If you also want to foam your drink, leave the attachment on the steam pipe. Make sure that the end of the steam pipe is always in the drink (approx. 2 cm), and not only in the foam for example, to prevent liquid from splashing upwards. Attention: For the best result, always first hold an empty cup under the steam pipe and open the steam controller for approx. 15 seconds. In the first shot of steam there is often a lot of water, which can be released in this way.
-
Slowly turn the steam controller, after which the steam sprays out of the steam pipe and your drink is heated up. The amount of steam can be controlled by turning the button. Warning: Never turn the steam controller too quickly, too much steam could be created too quickly otherwise, which in rare cases could lead to an explosion.
-
When your drink has reached the required temperature, turn the steam controller to the closed position again (turned to 0). After each use, you must properly flush through the steam pipe once to remove residues of (chocolate) milk. For this, hold an empty cup under the steam pipe. Slowly turn open the steam controller and press down the coffee button
( ). Water is spraying from the steam pipe. After 30 seconds, press the coffee button ( ) once more and close the steam controller again (turned to 0). Throw the water away after flushing. If applicable, remove the attachment from the steam pipe and clean it as described in section CLEANING AND MAINTENANCE. Do make sure you do not burn yourself!
Attention: -
If you want to make coffee immediately after using the steam pipe, the appliance is still too hot for making coffee. After using the steam pipe, we recommend switching off the appliance and allowing it to cool down for at least 5 minutes, before making coffee.
-
When the appliance fails while steam is being released, the residual heat ensures that steam continues to be released for a certain period of time. The appliance stops producing steam when you turn the steam controller off (turned to 0). Warning: The steam pipe becomes hot, only grab it by means of the supplied handle
CLEANING AND MAINTENANCE
Regularly clean the coffee machine. This is not only beneficial for the life
span of the appliance, it also ensures optimum use of the appliance and, of
course, good-tasting coffee.
Cleaning should involve the following:
-
Prior to cleaning, always check that the coffee machine is switched off, cooled down and that the plug has been removed from the socket.
-
Regularly clean the outside of the appliance with a slightly damp cloth and then wipe it dry with a dry cloth.
-
Regularly clean the water reservoir, leak tray and cup grille of the appliance with hot water and a mild washing-up liquid. Then rinse thoroughly with hot water and wipe dry.
-
Take the filter holder away from the appliance by turning it clockwise. Remove coffee residues and clean the filter holder, filters and measuring spoon/tamper with water and a mild washing-up liquid. Then rinse thoroughly with hot water and wipe dry. Attention! Avoid making contact with the blades in the filter for coffee capsules, these are very sharp.
-
Remove the attachment from the steam pipe and clean it with hot water and a mild washing-up liquid. Then rinse thoroughly with hot water and wipe dry. Wipe the end of the steam pipe clean with a slightly damp cloth and then wipe it dry with a dry cloth.
• Place back all components correctly in the appliance. Attention: Never use abrasives, alcohol or solvents when cleaning. Never rinse the appliance under the tap or submerge it in water.
STORAGE
When the coffee machine is not being used for a longer period of time, you must first release the steam in the appliance. This is
done as follows:- Check that the steam controller is switched off (turned to 0) and that the steam button ( ) is pressed down. Switch on the appliance by pressing the on/off button ( ) and wait until the steam indicator light lights up continuously.
- Turn the steam tube away from the appliance, use the provided handle for this. Hold a cup under the steam pipe to collect any released water. Warning: The steam pipe becomes hot, only grab it by means of the supplied handle.
- Then slowly turn the steam controller, after which the steam sprays out of the steam pipe. Allow the steam to escape for 3 minutes. Warning: Never turn the steam controller too quickly, too much steam could be created too quickly otherwise, which in rare cases could lead to an explosion.
- Then turn the steam controller closed again (turned to 0) and switch off the appliance. Allow the appliance to cool down and remove the plug from the socket. Attention! Avoid contact with steam, this could result in personal injury! Store the appliance on a dry location at a temperature that is higher than 0 °C
DE-SCALING
Regularly de-scale your coffee machine. The de-scaling intervals depend on the
hardness of the mains water and the frequency at which the coffee machine is
being used. We recommend de-scaling the coffee machine every 1-2 months. Due
to scaling, the heating element can become obstructed. This causes
overheating, as a result of which the coffee machine is switched off
automatically as a safety precaution and will no longer function. The coffee
machine will have to be repaired. You can de-scale the coffee machine with a
special de-scaling agent for coffee machines or with kitchen grade vinegar. If
you use a special de-scaling agent for coffee machines, you must observe the
instructions on the packaging of this agent. When using kitchen-grade vinegar,
proceed as follows:
- Switch off the appliance by pressing the on/off button ( ) and remove any remaining water from the water reservoir.
- Fill the water reservoir with clean, cold water and cold kitchen grade vinegar up to the MAX mark. The water and kitchen grade vinegar ratio should be 4:1. Place the filter holder with filter (without coffee) back in the appliance and place a cup on the cup grille.
- Check that the steam controller is switched off (turned to 0) and that the steam button ( ) is not pressed down. Switch on the appliance by pressing the on/off button ( ), after which the indicator light switches on.
- Press the coffee button when the coffee indicator light lights up. Allow the water to flow until your cup is full. Press the coffee button once more to stop the coffee making process and remove the water from the cup.
- Repeat step 4 and then wait 5 seconds.
- Press the steam button ( ) and wait until the steam indicator light remains on. Make steam for 2 minutes by slowly turning the steam controller. Hold a cup under the steam pipe to collect any water that is released. Turn the steam controller to 0 again and switch off the appliance by pressing the on/off button ( ). 7. Wait for at least 15 minutes, as a result the scale will be softened and removed.
- Check that the steam controller is switched off (turned to 0) and that the steam button ( ) is not pressed down. Switch on the appliance by pressing the on/off button ( ), after which the indicator light switches on.
- Press the coffee button and allow the appliance to run until the water reservoir is empty. The de-scaling process has been completed. Empty the cup and the removable leak tray to remove any water.
- After de-scaling, allow a full reservoir of cold water to flow through the appliance at least 3 times, to remove all de-scaling liquid and vinegar residues and thus prevent a sour taste in the coffee. Repeat all the above-mentioned steps, only now do not add kitchen grade vinegar to the water. It is not necessary to wait 15 minutes at point 7. Attention! If the coffee machine has not been used for some time, e.g. due to vacation, it is recommended to remove and clean all separate components. Then place the cleaned separate components back on their place and allow the coffee machine to make one run with clean water. In this way you will prevent a possible foreign taste.
BREAKDOWNS AND SOLUTIONS
In case of a breakdown, you must:
- switch off the appliance, if possible;
- remove the plug from the socket;
- apply for a repair;
- some small problems can be resolved by the user himself, using the instructions in the table below. Check all points in the table in sequence, before contacting the maintenance or customer service.
Breakdown (code) | Cause | What to do |
---|---|---|
Water is leaking from the bottom of the appliance. | There is too much water in | |
the leak tray. | Empty the leak tray. | |
The appliance is not working properly. | Contact the service department or |
customer service department.
There is water leaking from
the filter.
| There are coffee residues on the rim of the filter.| Remove the coffee residues.
The coffee has a sour, acidic
taste.
| The appliance has not been
properly rinsed after de-scaling.
| Clean the appliance several times, as indicated in section
PRIOR TO FIRST USE.
The coffee used has been stored on a warm, damp location, making it unfit for use.| Use fresh coffee and store unused coffee on a cool and dry location. Properly close an opened package and store it in a refrigerator to keep the coffee fresh.
The appliance no longer works.
|
The plug is not properly in the socket.
| Make sure the plug is properly inserted in the wall socket.
If the appliance is still not working, please contact the
maintenance department or customer service department.
The milk will not foam.
| The attachment has not been
placed on the steam pipe.
| Place the attachment on the steam pipe.
The steam indicator light does not light up.| The light must first switch on
before it is possible to foam milk.
The used milk container is too large or the shape is not correct.|
Use a high and narrow container.
The milk used is not correct.| Use full-cream or semi-skimmed milk.
When using, there are flakes
coming out of the steam pipe.
|
The steam pipe has not been properly cleaned.
|
Properly rinse the steam pipe, see section HEATING UP (CHOCOLATE) MILK
References
- Tomado Elektrische Apparaten - Vertrouwd sinds 1923
- Tomado Elektrische Apparaten - Vertrouwd sinds 1923
- Klantenservice
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>