INVENTUM AC901 Mobile Air Conditioner Instruction Manual

MOBILE AIR CONDITIONER
mobiele airconditioner
AC901

instruction manual

safety instructions

• Carefully and fully read the user manual prior to using the appliance and carefully store the manual for future reference.

• Do not use agents that accelerate the defrosting process or cleaning agents than those recommended by the manufacturer.

• Store the appliance in a room without any continuously active ignition sources (e.g. an open flame, switched a gas appliance, or switched the electric heating appliance).

• Do not drill through or burn.

• Caution, certain refrigerants do not have an odor.

• Install, use and store the appliance in a room with a floor surface of at least 7,7 m2 (for 9000Btu/h).

• Only install this appliance when it complies with local/national legislation and standards.
  IMPORTANT

• This appliance is intended for use as an air conditioner in houses and is only suitable for indoor use in living rooms, kitchens, and garages in dry locations, under normal domestic circumstances.

• Never use the appliance with a damaged cord or plug. Never clamp the cord and avoid contact with sharp edges.

• The installation should fully correspond with the locally applicable regulations, conditions, and standards.

• The appliance is only suitable for use on dry locations, indoors.

• Check the mains voltage.

• This appliance is only suitable for an earthed socket, connection voltage 220-240 Volt/ ~50 Hz.

• The appliance MUST always be connected in an earthed condition. If the power supply is not earthed, it is absolutely not permitted to connect the appliance.

• The plug must always be easily accessible when the appliance is connected.

• Has the electrical system been checked by a recognized expert if you are not certain that everything is in order?

• Never cover the air inlets and outlets.

• Empty the water reservoir via the water drain point, before moving the appliance.

• Never allow the appliance to come into contact with chemicals.

• Do not insert fingers or objects in the openings of the appliance.

• Never allow the appliance to come into contact with water. Do not spray the appliance with water or submerge it in water to prevent short-circuiting.

• Always first remove the plug from the socket before the appliance or a part thereof must be cleaned or replaced.

• NEVER connect the appliance using an extension cord. If there is no earthed socket available, have one installed by a recognized electrician.

• For reasons of safety, always be careful when there are children near this appliance, same as with any other electrical appliance.

• Do not use the appliance if the plug, cord, or appliance is damaged, if the appliance no longer functions properly or if it is damaged in any other way. If this is the case, consult the shop or our technical service. Never replace the plug or cord yourself.

• Always remove the plug from the socket when the appliance is not being used.

• Only have a damaged electricity cord replaced by the supplier or an authorized person/service point.

• Keep the appliance out of reach of children. Children do not see the dangers when handling electrical appliances. Therefore, never allow children to work with electrical appliances without supervision. Keep the appliance and cord out of reach of children younger than 8 years of age.

• The appliance can be used by children of 8 years and older and persons with a limited physical, sensory or mental capacity or lack of experience or knowledge, provided they use the appliance under supervision or have been instructed about its safe use and understand the hazards involved.

• Children are not allowed to play with the appliance.

• The appliance may not be cleaned or maintained by children unless this is done under supervision.
  CAUTION!

• Never close the room where this appliance is used in such a way that it is fully airtight. This prevents a vacuum from being created in this room. Negative pressure (=vacuum) could disrupt the safe operation of geysers, extractor hoods, ovens, etc.

• Non-observance of the instructions could invalidate the warranty on the appliance.

• Always lift the appliance with two persons.

• Always make sure the appliance is placed on a sturdy, flat surface.

• Do not leave the appliance unsupervised if the appliance is operational.

• If you want to move the appliance, make sure the appliance is switched off. Use both hands when moving the appliance.

• Never use the appliance with parts that are not recommended or supplied by the manufacturer.

• Do not pull the cord and/or appliance to remove the plug from the wall socket. Never touch the appliance with wet or moist hands.

• If the appliance does not function after it has been switched on, it is possible that the fuse or earth leakage circuit breaker has been activated in the electrical distribution box. The group can be overloaded or an earth leakage current may have occurred.

• In case of a breakdown, never make repairs yourself; a blown safety device in the appliance could indicate a defect that cannot be remedied by removing or replacing this safety device. Only original parts should ever be used.

• Never submerge the appliance, cord, or plug in water.

• This appliance is only suitable for household use. If the appliance is not used as intended, no compensation can be claimed in case of defects or accidents and the warranty will be invalidated.
  If you decide not to use the appliance anymore due to a defect, we recommend cutting off the cord after removing the plug from the socket.
  Household appliances do not belong in the dustbin. Take them to the waste processing department concerned of your municipality.

WARNING
Specific information for appliances with R290 refrigerant gas.

• Thoroughly read all warnings.
• When defrosting and cleaning the appliance, only use tools recommended by the manufacturer.
• Place the appliance in a room without any continuously active ignition sources (e.g. an open flame, switched on electric or gas appliance).
• Do not drill through or burn.
• Install, use and store the appliance in a room with a floor surface of at least 7,7 m 2 .
• This appliance contains 160-gram R290 refrigerant gas (see the information plate at the rear of the appliance).
• R290 is a refrigerant gas that is in accordance with the European environmental directives. Never drill through any part of the cooling circuit.
• If the appliance is installed, operated, or stored in a room without ventilation, the room should be made in such a way that the accumulation of refrigerant as a result of a leak is prevented. This could lead to a fire or explosion hazard due to the ignition of the refrigerant by an electric heating appliance, stove, or another ignition source.
• Store the appliance in such a way that mechanical failures are prevented.
• Persons operating or working at the cooling circuit must be in the possession of a suitable certificate from an authorized organization so that these persons are authorized to handle refrigerants in a safe way in accordance with the specifications that apply within the industry.
• Repairs may only be performed as recommended by the manufacturer of the appliance. Maintenance and repairs that require assistance from other trained personnel, must be performed under the supervision of a person who knows how to use combustible refrigerants.

REFRIGERANT
(CE) N 842/2006: This air conditioner contains the refrigerant R290. The quantity of refrigerant is less than 1 kg and is contained in a closed cooling circuit. The refrigerant does not have an ozone depletion potential. It is, however, a greenhouse gas according to the Kyoto protocol and could therefore contribute to global warming when released into the atmosphere. Only trained technicians with a suitable refrigerant certificate are permitted to fill or empty the appliance. If used correctly and when the refrigerant circuit is undamaged, your air conditioner does not have to be refilled with refrigerant. GWP: R290: 3.

appliance description

1.  Rear
2. Air inlet
3. Detachable air filter
4. Front
5. Operating panel
6. Louvre grille
7. Castor
8. Cord
9. Air inlet
10. Remote control
11.  Connection piece – round
12. Connection piece – rectangle
13. Discharge hose – air
14. Velcro fastener
15. Flexible window seal set

10.1 On/off key [POWER] 10.2 Timer key [TIMER] 10.3 Mode selection key [MODE] 10.4 Temperature down key [TEMP -] 10.5 Temperature up key [TEMP +] 10.6 Speed key [SPEED]

before using it for the first time

Follow these instructions when using the appliance for the first time: Carefully unpack the air conditioner and all accessories and remove all packaging material and any promotional stickers. Keep the packaging (plastic bags and cardboard) out of the reach of children. After unpacking the appliance, check it for external damage that may have occurred during transport. Place the appliance on a sturdy, flat surface and make sure there is enough space all around for sufficient ventilation. Check that all mentioned accessories have been supplied. Clean the air conditioner with a slightly damp cloth.
Prior to connecting the appliance, check that:

• the connection voltage corresponds with what is stated on the information plate;
•  the socket and cord are suitable for the appliance;
• the plug of the cord fits in the socket;
• the appliance is placed on a stable and flat surface.

INSTALLATION
A mobile air conditioner must be placed on a flat surface with sufficient room all around. Do not block the air outlet and ensure a free space of a minimum 30 cm around the air conditioner.
After placing the appliance in a straight position, allow it to stand for at least 2 hours before inserting the plug in the socket.

• Screw an end of the discharge hose [ a ] in the square connector [ b ].
• Place the square connector [ b ] in the fixing clamp [ c ] on the rear of the air conditioner.
• Ensure good air circulation and keep at least 30 cm around the air conditioner free.
• Hang the other end of the discharge hose to the outside. Ensure a free passage of the hose. Close the window or door to the extent possible.

REMARK: Optimum operation of the air conditioner depends on the length of the discharge hose and the number of bends. Try to limit both. The supplied flexible discharge hose has a maximum length of approx. 150 cm and corresponds with the capacity of the air conditioner. The use of any other hoses or extensions could cause failures in the appliance. The air should be able to flow without any hindrance, or else this could cause overheating of the appliance or condensation of water in the air discharge hose.  Therefore make sure there are no kinks or sharp bends in the discharge hose. In order to reach an optimum result, the discharge hose should be kept shorter than 1 meter during the use of the air conditioner.

INSTALLATION OF THE WINDOW SEAL SET
The flexible window seal set is suitable for many windows. Such as: tilt and turn windows, windows turning to the outside and inside. It ensures that you are able to hang the discharge hose to the outside, without hot air flowing indoors again or having problems with insects. For windows turning to the outside, we recommend taping all four sides (a+b+c+d) around the window, and for windows turning to the inside only three sides (a+b+c).

• Attach the supplied double-sided tape on the window frame and the window in accordance with one of the drawings below that is similar to your situation.
• Then attach the cloth to the tape that you attached in the openings.

1. Attach the supplied double-sided tape to the window frame.
2. Then attach the double-sided tape to the window.
3. Cut away excess tape.
4. Make sure the tapes on the corners properly overlap to achieve proper sealing.
5. Attach the cloth to the tape attached to the window frame and window.
6. Make sure the cloth is neatly attached to the tape on both sides.
7. Zip open the cloth.
8. Insert the discharge hose through the opening and zip the cloth closed to achieve proper sealing.

operation of the air conditioner

In addition to cooling, the air conditioner has two other functions, i.e. air circulation and dehumidification. The air conditioner can be operated via the control panel on the appliance and with the provided remote control.

• Choose a location near a socket.
• Install the discharge hose in accordance with the figures and make sure the window is closed as much as possible.
• Insert the plugin and earthed the socket.
• Press the on/off key to switch on the air conditioner.
• The temperature range of the air conditioner is: 18 to 35°C.
• Check that the discharge hose is mounted correctly.
• Do not share the socket with any other appliances.

COOLING

• Press the [ MODE / ] key until the symbol appears in the display.
• Press the [ TEMP and TEMP ] keys to set the required room temperature (between 16°C and 31°C).
• Press the [ SPEED / ] key to adjust the wind speed.

DEHUMIDIFICATION

• Press the [ MODE / ] key until the symbol appears in the display.
• The air conditioner automatically adjusts the temperature to the current room temperature minus 2°C.
• The wind speed is at low speed automatically. This cannot be changed.

AIR CIRCULATION

• Press the [ MODE / ] key until the symbol appears in the display.
• Press the [ SPEED / ] key to set the wind speed – high or low .

ADJUSTING THE TIMER –
The timer function can be used to allow the air conditioner to switch on automatically (delayed start) or switch off automatically at a set time (automatic deactivation).

Delayed start

• Press the timer key when the air conditioner is off and select the required time at which you want the air conditioner to switch on by means of the [ TEMP and TEMP ] keys. The delayed start can be set between 0 and 24 hours.
• Confirm the number of hours by pressing the timer key once more.
• The set number of hours is shown in the display.
• When the set number of hours has passed, the air conditioner switches on automatically.

Automatic deactivation

•  Press the timer key when the air conditioner is on and select the required time at which you want the air conditioner to switch off by means of the temperature and time keys [ TEMP and TEMP ]. Automatic deactivation can be set between 0 and 24 hours.
• Confirm the number of hours by pressing the timer key once more.
• The set number of hours is shown in the display.
• When the set number of hours has passed, the air conditioner switches off automatically.

WATER DRAINAGE
When the air conditioner is not used for a longer period of time, remove the rubber cap from the drain opening at the bottom of the appliance and place an empty cup under the outlet. All the water will flow out of the tank. The water tank is equipped with an alarm sensor. When the water reaches a certain level in the water tank, the indicator light lights up. Should the water pump be defective, this could be an option for draining the water, as the water pump is not used in this way. The air conditioner will still be able to function properly. When the water pump is defective, intermediate drainage can also be used. Keep an eye on the indicator light for the full water tank , to see whether it lights. Once the indicator led lights, connect a discharge hose in the same way and all the water will flow out of the tank. In this way, the air conditioner is also able to function properly.

cleaning and maintenance

Just before cleaning your air conditioner, switch off the appliance, remove the plug from the socket and allow the appliance to cool down fully.

Cleaning the exterior
Clean the exterior of the appliance with a damp cloth or sponge. If necessary, you can clean the exterior of the appliance by means of a mild detergent.

• Do not use aggressive or abrasive cleaning agents for cleaning the appliance.
• Dry the exterior of the appliance.
• Never submerge the appliance, cord, or plug in water or any other liquid.

Cleaning the air filter
In order to allow the air conditioner to function as well as possible, we recommend cleaning the air filter every two weeks. The air filter could get clogged with dust and dirt.

• Pull the air filter out of the air inlet on the side of the appliance.
• Clean the air filter with a mild detergent in lukewarm water (approx. 40°C) and allow it to dry in the air. Do not place the air filter in the sun or on the heating radiator to dry it.
• Slide back the air filter. Check that it is fully dry, before using the air conditioner again.

Cleaning the ventilation grilles
In order to allow the air conditioner to function as well as possible, you can clean the ventilation grilles by means of a vacuum cleaner with a soft brush nozzle.

problems and remedies

First check the following before submitting the air conditioner for repair.

tank.
The room temperature is lower than the set temperature.| Set the temperature once more.
The appliance does not cool sufficiently.| Not all doors and windows are closed.| Make sure that all doors and windows are closed.
There are heat sources that are active in the room.| Remove the heat sources or switch them off if possible.
The temperature is set too high.| Set the temperature once more.
The air inlet is blocked.| Clean the air inlet grille.
The appliance makes a lot of noise.| The surface on which the appliance is placed is not level of flat enough.| Place the appliance on a flat surface, level if possible.
The noise is caused by the flowing refrigerant liquid within the air conditioner.| This is normal.
Error code EO| The sensor of the room temperature is defective.| Have the sensor replaced (the appliance is also able to function without replacing the sensor).
Error code E2| The water tank is full.| Empty the water tank.

technical specifications

Type number
Voltage
Connected load
Cooling capacity
EE Class
HER*
Power consumption kW
Power consumption Standby W
Current consumption nom. A
Air displacement max. m3/h
Dehumidification max. ** L/24h
Suitable for m3
Refrigerant / GWP type/gr
Thermostat range °C
Fan speeds
Max. noise level dB(A)
Dimensions (hxwxd)
Nett weight
Protection class
Remote control| AC901
220-240Volt ~50Hz
1000 Watt
9000Btu/h (2.6kW)
A
2.6
1.00
0.5
2.6 kW
320
28
80
R-290 / 3 /160 g.
16 – 31
2
65 dB(A)
680 x 330 x 280 mm
19.0 kg
IP 20
yes
---|---

general terms and conditions of service and warranty

We do not need to remind you of the importance of service. After all, we develop our products to a standard so that you can enjoy them for many years, without any concerns. If, nevertheless, there is a problem, we believe you are entitled to a solution straight away. Hence our products come with an exchange service, on top of the rights and claims you are entitled to by law. By exchanging a product or part, we save you time, effort, and costs.

2-year full manufacturer’s warranty

1. Customers enjoy a 2-year full manufacturer’s warranty on all Inventum products. Within this period, a faulty product or part will always be exchanged for a new model, free of charge. In order to claim under the 2-year full manufacturer’s warranty, you can either return the product to the shop you bought it from or contact the Inventum customer service department via the form at www.invented.eu/service-aanvraag.
2. The 2-year warranty period starts from the date the product is bought.
3. In order to claim under the warranty, you must produce a copy of the original receipt.
4. The warranty applies only to normal domestic use of Inventum products within the Netherlands.

5-year Inventum warranty

1. Inventum offers a 5-year warranty on most large domestic appliances and a selection of small domestic appliances. This 5-year Inventum warranty consists of a 2-year full manufacturer’s warranty, extended by a further 3-year warranty. The only thing you need to do to qualify for the 3-year extended warranty is to register the product within 45 days of purchase. You can read more about registering the product in the following paragraph.
2. In accordance with the 5-year Inventum warranty provisions, a faulty product or part will always be exchanged for a new model during the first 2 years under the warranty. During the 3rd to 5th year under the warranty, you will only pay the costs of exchange. The current costs of exchange are listed at www.invented.eu/omruilkosten.
3. In order to claim under the 5-year Inventum warranty, you can either return the product to the shop you bought it from or contact the Inventum customer service department via the form at www.invented.eu/service-aanvraag.
4. The 5-year warranty period starts from the date the product is bought.
5. In order to claim under the warranty, you must produce a copy of the original receipt.
6. The warranty applies only to normal domestic use of Inventum products within the Netherlands.

Product registration

1. The 3-year extended warranty is easy to obtain, free of charge, by registering the product within 45 days of purchase, via the website www.invented.eu/Garantie-registratie. If you did not register the product within 45 days of purchase, you can still do so up to 2 years after the purchase date. However, there will be a charge. The one-off registration charge is € 89 for each separate product. Registration is possible only for products that are subject to the 5-year Inventum warranty. Whether the product qualifies for the 5-year Inventum warranty is stated in the product user manual and in the product information sheet, on Inventum’s website.
2. The warranty period always starts from the date the product is bought. If the product is registered for the extended warranty at a later date, the warranty period still starts from the original date of purchase.
3. The 3-year extended warranty can only be applied for if you are in the possession of a copy of the original receipt and the Inventum 5-year warranty certificate.

Large domestic appliances

1. Breakdowns or faults in large domestic appliances (separate and built-in white goods) can be registered via the form at www.invented.eu/service-aanvraag, by calling the Inventum customer service department or in the store where you bought the device. The telephone number of the customer service department can be found at www.invented.eu.
2. In the event of breakdowns or faults in large domestic appliances, Inventum will have the option to have a service engineer inspect the faulty device onsite at the customer in the Netherlands and to carry out repairs, there and then. The Inventum customer service department can also decide to have the device exchanged.
3. If you suffer a breakdown or fault in a large domestic appliance during the first 2 years from the date of purchase, Inventum will not charge any costs for the exchange, call-out or for parts and labor.
4. If you registered the product as described before at www.invented.eu/Garantie-registratie and you subsequently report a breakdown of a large domestic appliance in the 3rd to 5th year of the date of purchase, the 5-year Inventum warranty applies and the device will be repaired or exchanged, free of charge. In the event of a repair or exchange of the device, you only pay the costs of the exchange. The current costs of exchange are listed at www.invented.eu/omruilkosten. If you did not register the product, the 3-year extended warranty does not apply.
5. When reporting a breakdown or fault, a service engineer will contact the customer within 1 working day in order to make an appointment. When the report is made in a  weekend or during a public holiday, this will be the next working day.
6. If you report a breakdown or fault via the form at www.inventum.eu/service-aanvraag, you will be kept informed of the progress via mobile messages and e-mail.
7. The warranty period starts from the date the product is bought.
8. In order to claim under the warranty, you must produce a copy of the original receipt and the Inventum 5-year warranty certificate.
9. The warranty applies only to normal domestic use of Inventum products within the Netherlands.

Breakdowns or faults outside the warranty period

1. Breakdowns or faults in small or large domestic appliances outside the warranty period can be reported to the customer services department via the form at www.inventum.eu/service-aanvraag or by calling the customer services department.
2. The customer services department may ask you to send the product for inspection or repair. The costs of dispatch will be at your expense.
3. The inspection to establish whether the repair is possible involves a charge. You need to grant your permission for this, in advance.
4. In the event of a large domestic appliance, Inventum, at your request, can send out a service engineer. In that case, you will be charged the call-out costs, as well as parts and labor.
5. In the event of an instruction to repair, the repair costs must be paid in advance. In the event of a repair by a service engineer, the costs of the repair must be settled with the engineer on site, preferably by means of PIN payment.

Warranty exclusions

1. The following is excluded from the aforesaid warranties:
   • normal wear and tear;
   • improper use or misuse;
   • insufficient maintenance;
   • failure to comply with the operating and maintenance instructions;
   • unprofessional installation or repairs by third parties or the customer himself;
   • non-original parts used by the customer;
   • use for commercial or business purposes;
   • removal of the serial number and/or rating label.

2.  In addition, the warranty does not apply to normal consumer goods, such as:
   • dough hooks, baking tins, (carbon) filters, etc.;
   • batteries, bulbs, carbon filters, fat filters etc.;
   • external connection cables;
   • glass accessories and glass parts such as oven doors;
   • and similar items.

3. Transport damage not caused by Inventum is also excluded. Therefore, inspect your new device before starting to use it. If you detect any damage, you must report this to the store where you purchased the product within 5 working days, or to the Inventum customer service department via the form at www.inventum.eu/service-aanvraag. If transport damage is not reported within this period, Inventum does not accept any liability in this respect.

4. The following are excluded from warranty and/or replacement: faults, loss of, and damage to the device as a result of an event that is normally insured under the home contents insurance.

Important to know

1. The replacement or repair of a faulty product, or a part thereof, does not lead to an extension of the original warranty period.
2. Parts that have been replaced, packaging material, and exchanged devices are taken back by the service engineer and become the property of Inventum.
3. If a complaint is unfounded, all costs arising from it will be at the customer’s expense.
4. Following the expiry of the warranty period, all costs of repair or replacement, including administration costs, dispatch, and call-out charges, will be charged to the customer.
5. Inventum cannot be held liable for damage as a result of devices built-in incorrectly.
6. Inventum cannot be held liable for damage caused by external events unless this liability arises from mandatory statutory provisions.
7. These warranty and service provisions are governed by Dutch law. Disputes will be settled exclusively by the competent Dutch court.

Inventum Huishoudelijke
Apparaten B.V.
Postbus 5023
6802 EA Arnhem
www.inventum.eu

instagram.com/inventum1908
facebook.com/inventum1908
youtube.com/inventum1908

AC901-versie 02/02.1120V
Modifications and printing errors reserved

References

• Inventum Huishoudelijke Apparaten - Altijd 5 jaar garantie!
• Inventum Huishoudelijke Apparaten - Altijd 5 jaar garantie!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>