JOYO MW-1 266-00MW1-0010 Wireless Microphone User Manual
- June 5, 2024
- JOYO
Table of Contents
JOYO MW-1 266-00MW1-0010 Wireless Microphone
Product Introduction
Thank you for purchasing JOYO wireless microphone system MW-1I
It’s specially designed for moving-coil microphone, changing microphone into a
wireless one, user-friendly setup and without cables, suitable for various
venues
Features
- A built-in rechargeable lithium battery
- Transmission distance> 30 meters
- It adopts 5.8GHz ISM frequency band
- 4 switchable channels
- Delay time < 5ms
- 24 bit Audio Resolution with Sampling Frequency of 48K
Caution
- Do not disassemble or repair this product by yourself.
- Do not use or store ii to any heat sources, damp, dusty areas. Avoid violent vibrations or shock.
- Do not drop this product otherwise It may malfunction.
- Do not use alcohol or other cleaning fluids to clean this product.
- This product works normally only when the transmitter and the receiver pairs up.It supports one-to-one and one-to-many.
- Please make sure the transmitter and the receiver keep e distance away from wireless router or other wireless equipment during use.
- Obstructions between the transmitter and the receiver may affect the transmission distance.
- A maximum of 4 sets of transmitters and receivers can be used in the same place simultaneously.
- If the red light flashes during use, It Ind locates low battery, please charge It In time.
- Plaase turn off the transmitter and the receiver when not In use.
- Due to one of the characteristics of llthlum battery, there Is a slight self-discharge. Therefore please charge the battery in 2 months so as to avoid low battery protection.
- The lithium battery capacity decreases gradually after rape a tad charge and discharge, so this product’s life time will be affected within acceptable degree with lime.
Panel
Transmitter
- Channal switch /Pairing Button
- Channel Ind locator
- Power switch-Long press it to turn on or turn off
- Micro-USB Port
- Female Port
- Fastener button
- Status indicator
Receiver
- Pairing Button
- Channel indicator
- Female Port
- Power swltch-Long press it to turn on or turn off
- Micro-USB Port
- Status indicator
Transmitter and Receiver Pairing
The default setting for MW-1 microphone wireless system is Channel
- if you wantto use other channels, please proceed according to the following steps:
- Turn on the receiver and the transmitter.
- Connecl the receiver to the microphone and the transmitter to the mixer or other equipment.
- You can long press the channel switch button to pair up the channels of the receiver and the transmitter, the signal Is to be paired up when the status indicator flickers blue.
- When they’re paired successfully, the status indicators on both of the transmitter and the receiver become blue.
Specifications
MW-01 receiver
- Power supply mode: built-in lithium battery
- Cell capacity: 3.7V 400mAh+3.7V18OmAh
- Reception Sensitivity: -85dBm
- Received frequency: 5.8GHz frequency
- Anti-jamming method: Frequency hopping
- Signal Distortion: <0.02%
- Gain: 0 dB
- SNR: 105dB
- Frequency response: 20Hz – 20KHz
- Delay time: <5ms
- Sampling rate: 24-bit /48KHz
- Output Impedance: 680Q
- Port’s type: XLR male port
MW-01 transmitter
- Power supply mode: built-in lithium battery
- Cell capacity: 3.7V 400mAh+3.7V180mAh
- Transmission power: 7dBm
- Working frequency: 5.8GHz frequency
- Anti-jamming method: Frequency hopping
- Frequency response: 20Hz – 20KHz
- Delay time: <5ms
- Sampling rate: 24-bit /48kHz
- Input Impedance: 3.3K
- Port’s type: XLR female port
Application scenarios
- Wireless recording
- Conventional use
Battery charging
You can see the receiver and transmitter’s battery level when you turn on the
unit and the related channel’s indicators.
When the status indicator
starts to flicker in red, it indicates low battery, and it’s time to charge
the unit.
When the unit is being charged, the status indicator is in red.It goes off
when it’s fully charged.
You can charge the transmitter and receiver simultaneously with the Dual Port
USB Cable.
JOYO TECHNOLOGY CO., LTD
Address:
2/F, Lushi Industry Building, 28th District, Bao’an, Shenzhen, 518133 China.
www.joyoaudio.com
Email:info@joyoaudio.com
Tel: 0086-755-29765381
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>