YOUHA TheOne Double Electric Breast Pump Instructions

YOUHA TheOne Double Electric Breast Pump Instructions

Important information

Preparation is important

• Wash your hands with soap and water and dry them thoroughly before assembling parts for expressing.
• Ensure all parts of the pump are clean and dry before each use.

Taking care and safe use of your Youha The One product.

• This product is a personal care item and use should not be shared between mothers.

• If you experience any pain while using The ONE Double Electric Breast Pump, seek professional advice from a lactation consultant to ensure you have the best fitting breast shield for you.

• Replace the valves after every 1 month of use, or sooner if signs of wear or weakness, to ensure good suction (2 spare valves included).

• Replace PPSU bottles and storage lids at signs of wear or every 3-6 months.

• Inspect teats prior to each use and pull in each direction. Teats may be worn by biting. Replace on signs of wear or weakness or every 2-3 months.

• Replace all other pump parts on signs of wear or weakness, or after 3 months of use.

• Avoid harsh detergents or hard scourers and sponges as this may scratch or damage the product. Exposure to detergent may make the silicone appear cloudy over time.

• Use of certain electric steam sterilisers (which may overheat parts) or UV
  sterilisers is not recommended as it will shorten the lifespan of the parts or possilby damage them.

• Do not use a cleaning brush inside the valves as this may damage the valve or shorten its lifespan.

• Store all parts in a cool, dry space and avoid direct sunlight.

• Do not leave the motor unit on charge for longer than 24-hours as this may damage the unit permanently and/or cause a safety risk.

• Keep out of reach of children. This product contains small parts which may be a choking hazard.

Product description

*Breast shields included are sizes 24 and 27
Breast shield converters change size 24 to 21

Note: Breast shields size 21, 30 and 36 are sold separately

Key functions Cleaning

Battery indicator

Note: Avoid leaving on charge for longer than 24-hours as this may damage the unit permanently.

Cleaning

Parts of the pump that do not come in contact with breastmilk do not require cleaning on each use. Clean these parts prior to the first use per instructions below and again whenever you see necessary. All other parts, which do come in contact with breastmilk, are cleaned and sanitised per instructions on page 11.

Parts that do not come in contact with breastmilk are:

• Motor unit
• Charger
• Tubing
• Tubing connector
• Membrane cap

Instructions: When necessary, wipe the motor unit with a soft, damp cloth while the unit is off and locked. Do not submerge the motor unit or charger in water or sanitiser.

When cleaning the Y-shape tubing and membrane cap, they can be cleaned following the steps on page 11. Ensure tubing is completely dry before use.

Clean and sanitise all other parts of the pump, which come in contact with breastmilk, prior to first use and after each subsequent use.

A. Before first use:

1. Disassemble all parts.
2. Wash in warm soapy water.
3. Rinse well.
4. Submerge parts in a pot of water and boil for 3-5 minutes. Use a large pot to avoid parts touching sides or bottom of pots.
5. Shake of excess water and air dry on a dedicated rack or clean cloth.

B. After each use:

1. Disassemble all parts. Put away those parts that don’t come in contact with breastmilk.
2. Rinse remaining parts with cold water to remove breastmilk.
3. Wash in warm soapy water. Valves can be cleaned by gentle rubbing between fingers.
4. Rinse well.
5. Shake of excess water and air dry on a dedicated rack or clean cloth.

How to sanitise:

• Follow cleaning step B1-4.
• Submerge parts in a pot of water and boil for 3-5 minutes. Use a large pot to avoid parts touching sides or bottom of pots.
• Shake off excess water and air dry on a dedicated rack or clean cloth.

Instructions for use: preparing to express

Insert the valve into the valve base from underneath. Push the valve in as far as it will go.

Screw the valve base clockwise onto the bottle until it is securely fastened.

Place the membrane into the valve base from above. Make sure it fits securely around the rim by pressing down with your fingers to ensure it seals completely.

Attach one end of the tubing to the connection point on the motor unit and the other end to the membrane cap. Press the membrane cap onto the membrane until it is securely in place.

If you wish to convert to size 21, place breast shield converter into the size 24 breast shield; push it in as far as it will go.

Note: While preparing your pump, place the converter dust cap on the breast shield to keep the silicone free from dust

If using a breast shield converter, ensure that it completely seals by pressing the converter down along the rim of the breast shield. Press in between the petals to remove any trapped air.

Double breast pumping

For double breast pumping, use Y-shape tubing. Connect each short end into membrane cap of each pumping kit. Connect long end into right side of motor unit.

Single breast pumping

For single breast pumping, insert unused short tubing back into Y-shape tubing connector. This closes the vacuum loop. Or, swap Y-shape tubing with single tubing.

How to charge:

If battery indicator flashes red, battery requires charging.
To charge, insert power cable into connection point on left side of motor unit, plug into a power outlet and switch on at the outlet. Charge until battery indicator green light to stop blinking, it is fully charged. Switch power off at outlet. Disconnect both pump and power outlet before use.

Instructions for use: operating the breast pump

Wash your hands with soap and water, dry them thoroughly before assembling parts for expressing.

Relax in a comfortable chair.

Position the breast shield against your breast. Make sure that your nipple is centred so that breast shield creates an airtight seal.

To lock, hold the On/Off button for five seconds until ‘lock’ appears on the screen and you hear a beep. To unlock, hold the On/Off button for five seconds while a countdown from five to zero displays on the screen and until you hear a double peep. These functions can be used while the pump is in operation or switched off.

Press the On/Off button
The breast pump will automatically start in massage mode. To change the level of the massage, use the Increase and Reduce buttons.

Massage mode will run for two minutes and then automatically change to the express mode used when the pump was last turned off

If you feel the letdown sooner, or when breastmilk begins to flow, press Mode key to change from massage to express mode.
You can press Mode again to change to deep express mode (this is not recommended for beginners).
Use the Increase and Reduce buttons to choose the level that is most comfortable for you.

Once the flow of breastmilk begins to slow down, finish pumping.

Use the On/Off button to turn the breast pump off.

Remove the pump from your breast and remove the tubing from the membrane cap.

Unscrew the pumping kit from the bottle and set it aside.

If you are about to feed immediately, connect teat to the bottle.

If you are storing the breastmilk, connect the cap to seal the milk for storage.

Note: take care when storing breastmilk and follow professional health guidelines.

Clean and sanitise the parts of the pump that came into contact with breastmilk (see “Cleaning” section of this manual).

Instructions for use: advanced settings

Mixed mode

If you are on express or deep express mode and you feel a little to try mixed mode. Mixed mode adds cycles of massage mode in between each express or deep express mode cycle.

Instructions

Follow steps 1-5

Hold down the Mode button for three seconds, until both the Massage and Express icons appear, to indicate that you are in mixed mode.

Note: In mixed mode, the suction and cycle is the same level with massage and express mode, so you may adjust the level which fits for you before change to mixed mode.

Manual mode

If you find that the three preset modes (Massage, Express and Deep Express) aren’t quite right for you, you might like to try manual mode. Manual mode gives you the ability to customise both the vacuum strength and cycle length to suit you.

Instructions

Follow steps 1-5

Press the Manual button.

Press the Vacuum Setting button and use the Increase and Reduce buttons to set the most suitable vacuum level for you.

Then press the Cycle Setting button and use the Increase and Reduce buttons to set the most suitable cycle level for you

You have now created a custom setting using the manual mode function.

Note: If you turn the pump off while using this mode it will restart on this mode, i.e., on the last setting used. Press the Mode button to start with massage mode and, after the breastmilk starts to flow, press the Mode button again to change back to your custom setting.

Troubleshooting

before use.
If condensation occurs, ensure that tubing dries completely after each use. To do this, disconnect the tubing from the membrane cap and turn the pump back on to dry the tubing while you are packing up the breastmilk
Milk in tubing| Check the membrane for damage. Replace the membrane if needed and clean and sanitise or replace the tubing.
Low or no suction| Ensure you have the correct fit breast shield. A good fit will ensure a good level of suction. You may wish to speak to a Lactation Consultant to assist in finding the most appropriate size for you
If using as a single pump with y-shape tubing, check that the other side of the tubing is firmly connected into the top of the y-shape tubing connector
Check that all parts are securely assembled.
Check the valves for any dam
Nipple pain| Seek advice from a Lactation Consultant.

Warranty and contact details

The ONE Double Electric Breast Pump has a 12-month warranty from time of purchase on product faults. Please contact your local Youha distributor for further warranty information or if you wish to order replacement parts.

Welcome to your Youha Double Electric Breast Pump

Offering you a single or double, more enjoyable and discreet way to express breastmilk. The ONE collection is designed to use anytime you like, wherever you like.

• Sleek and compact design
• Quiet and convenient operation
• Easy to use touchscreen
• Efficient and effective breastmilk expression
• Ideal for use at home or at the office

The ONE Double Electric Breast Pump is a high-quality, closed system. All parts that come in contact with breastmilk are free from Bisphenol A (BPA) and Diethylhexyl Phthalate (DEHP).

You can pair this system with The ONE Express Cups* to achieve a hands-free, more versatile and enjoyable way to express breastmil

We hope The ONE Double Electric Breast Pump supports you in a better breastfeeding experience.
We would love to hear from you!
If you have feedback or wish to share your breastfeeding story with us, please send us an email at: Service@youha.com

Customer Support

Hong Kong & Macau Sole Distributor
Power Grand I&E Ltd
Flat E, 22/F, Block 3, Golden Dragon Industrial Centre,
172-180 Tai Lin Pai Road
Kwai Chung, N.T.
Hong Kong
Tel: +852 3188 1030
www.youha.com.hk

Australia & New Zealand Sole Distributor
Youha Australia
PO Box 1109
St Leonards, VIC 3223
Australia
Tel: +61 423 111 573
www.youha.com.au

Proudly Made in China
Manufactured by:
Ningbo Youhe Electrical
Appliance Technology Co., LTD

References

• Youha Australia
• Youha Breastpump | Hong Kong | 優合 | 香港

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>