SOMOGYI ELEKTRONICS FKG 850 WIFI Smart Infrared Towel Dryer Instruction Manual
- June 5, 2024
- SOMOGYI ELEKTRONICS
Table of Contents
FKG 850 WIFI Smart Infrared Towel Dryer
Instruction Manual
Safety and maintenance
| STRUCTURE (Figure 1.)
---|---
1.| main switch
2.| display
3.| on/off button
4.| child lock
5.| timer
6.| heating mode
selector
7.| thermostat
setting buttons
8.| wall brackets
9.| dowels
10..| spacers
11..| washers
12.| nuts
13.| screws
IMPORTANT SAFETY INSTRUCTIONS
READ THE INSTRUCTION MANUAL CAREFULLY BEFORE USE AND RETAIN IT FOR LATER
REFERENCE!
WARNINGS
- Before using the product for the first time, please read the instructions for use below and retain them for later reference. The original instructions were written in the Hungarian language.
- Children below the age of 3 years should be kept away from the appliance, except where they are under constant supervision. Children between the age of 3 and 8 may only switch the appliance on/off provided that it has been set up and installed in the normal operating position and they are under supervision or have been instructed how to operate the appliance safely and understand the hazards associated with use. This appliance may only be used by persons with impaired physical, sensory or mental capabilities, or lacking in experience or knowledge, as well as children from the age of 8, if they are under supervision or have been given instruction concerning use of the appliance by a person responsible for their safety and they have understood the hazards associated with use. Children should not be allowed to play with the unit. Children may only clean or perform user maintenance on the appliance under supervision. WARNING: Parts of this appliance can become very hot and could cause burns. Extra care should be taken when children or handicapped persons are around.
- Confirm that the appliance has not been damaged in transit!
- Do not use this heater if it has been dropped!
- Do not use if there are visible signs of damage of the heater!
- Never locate the appliance directly in corners and observe the minimum installation distances indicated in the 2. figure. Always observe the health and safety regulations valid in the country of use!
- The appliance should be used as intended for warming air, not for general heating purposes.
- The stream of hot air should not be directed straight to curtains or other flammable materials!
- Do not locate near flammable materials (min. 100 cm).
- Do not use in locations where flammable vapors or explosive dust may be released. Do not use near flammable materials or in potentially explosive atmospheres!
- WARNING! The appliance is only intended for drying laundry washed in water.
- It is PROHIBITED to use the appliance near bathtubs, basins, showers, swimming pools, or saunas!
- It is STRICTLY PROHIBITED to install or use the appliance in zones 0 and 1 of premises containing bathtubs or showers (see 4. figure)!
- All circuits in premises containing bathtubs or showers shall be protected with one or more RCDs with a rated triggering current of up to 30 mA!
- Observe the local or special national regulations when installing an appliance on-premises containing bathtubs or showers.
- The heater has to be mounted in such a position, so as to disable the person staying in the bathtub or under the shower to touch the switches and other control appliances.
- It is forbidden to place the appliance directly below a power socket!
- When locating and mounting the appliance, please take into account the wall material and its bearing capacity!
- Before powering on the appliance, make sure it is fixed and stable on the wall!
- Operate only under constant supervision!
- Do not operate unattended in the presence of children!
- It is prohibited to use the appliance in motor vehicles or in confined spaces (< 5 m 2 ) such as elevators!
- When not planning to use the appliance for an extended period of time, switch it off then remove the power plug from the outlet!
- Always remove power from the heater before moving it!
- If any irregular operation is detected (e.g., unusual noise or burnt odor from the appliance), immediately switch it off and unplug the power plug!
- Make sure that no foreign objects or liquid can enter the appliance through the openings.
- Protect from dust, humidity, sunlight, and direct heat radiation!
- Power off the appliance by unplugging it from the electric outlet before cleaning!
- Do not touch the appliance or the power cable with wet hands!
- The appliance may only be connected to properly grounded 230 V ~ / 50 Hz electric wall outlets!
- Unwind the power cable completely!
- Do not lead the power cable on the appliance, or near the air inlet and outlet openings!
- Do not lead the power cable under carpets, doormats, etc.!
- Do not use extension cords or power strips to connect the appliance!
- The appliance should be located so as to allow easy access and removal of the power plug!
- Lead the power cable so as to prevent it from being pulled out accidentally or tripped over.
- The appliance is intended for household use. No industrial use is permitted!
- Due to continuous improvements, the technical data and design may change without any prior notice.
- The actual instruction manual can be downloaded from www.Somogyi.hu website.
- We don’t take the responsibility for printing errors that may occur, and apologize for them.
CAUTION: RISK OF ELECTRIC SHOCK!
Do not attempt to disassemble or modify the unit or its accessories. In case
any part is damaged, immediately power off the unit and seek the assistance of
a specialist.
In the event that the power cable should become damaged, it should only be
replaced by the manufacturer, its service facility or similarly qualified
personnel.
DO NOT COVER!
COVERING THE UNIT CAN CAUSE OVERHEATING, FIRE, OR ELECTRIC SHOCK.
INSTALLATION
- Before installation, carefully remove the packaging and make sure not to damage the unit or the connecting cable. If you find any damage, the unit must not be operated!
- Take out the unit from the box.
- To ensure proper operation, you have to arrange for the free circulation of hot air. Therefore, please, observe the minimum clearances indicated in Figure 2.
- Drill holes in the wall according to Figure 3.
- Fasten the wall brackets (8) to the wall using the dowels and 2 screws each. Select dowels adjusted to the wall structure and the size of the screws. Make sure that the brackets are aligned horizontally and that the notches of the brackets face upwards.
- Place 1 washer (11) and 1 nut (12) on each of the upper threaded stems on the back of the unit making sure to leave no more than 1 cm between the unit and the washer.
- Screw the spacers (10) on the two lower threaded stems on the back of the unit.
- Hang the unit onto the wall brackets by the two upper threaded stems. Make sure that the notch on the wall bracket is between the back of the unit and the washer.
- If necessary, you can position the product on the wall by tightening the nuts or adjusting the spacers.
- The switches on the unit must be in the OFF position!
- Plug the unit into a standard grounded wall socket. Now the unit is ready for operation!
CLEANING, MAINTENANCE
In order to ensure optimum functioning, the appliance may require cleaning at least once a month, depending on the manner of use and degree of contamination.
- Switch off and power off the appliance by unplugging it from the electric outlet before cleaning.
- Allow the appliance to cool down (for at least 30 minutes).
- Use a slightly moistened cloth to clean the appliance’s outer surface. Do not use any aggressive cleaners.
Avoid getting water inside of and on the electric components of the appliance!
TROUBLESHOOTING
| Cause | Solution |
|---|---|
| The appliance is not working in the heating stages. | Check the power supply! |
Check the thermostat settings!
Overheating protection may activated!
The overheating protection activates frequently.| Clean the appliance!
DISPOSAL
Waste equipment must be collected and disposed of separately from household
waste because it may contain components hazardous to the environment or
health. Used or waste equipment may be dropped off free of charge at the point
of sale, or at any distributor which sells equipment of identical nature and
function. Dispose of products at a facility specializing in the collection of
electronic waste. By doing so, you will protect the environment as well as the
health of others and yourself. If you have any questions, contact the local
waste management organization. We shall undertake the tasks pertinent to the
manufacturer as prescribed in the relevant regulations and shall bear any
associated costs arising.
Simplified EU Declaration of Conformity
Somogyi Elektronic Ltd. certifies that the FKG 850 WIFI radio equipment
complies with the 2014/53 / EU directive. The full text of EU Certification of
Conformity is available at the following link:
somogyi@somogyi.hu
FEATURES
smart infrared heating panel for heating indoor air and drying towels
- control via touch buttons or smartphone application
- 850 W output
- electronic thermostat
- weekly program
- child lock
- IPX4 protection from water splash
- glass front panel
- metal towel rail
- wall mounted design
- automatic shut-off in case of overheating
OPERATION
The device can be controlled via its touch buttons or a free smartphone app.
Using the touch buttons of the device: After connecting the device to the
mains, turn it on using the main switch. The device briefly beeps. You can use
the button to turn the device on/off. You can check the measured temperature
on the left side, and the set temperature value on the right side of the
display. Use the touch buttons (7) of the device to set the desired
temperature between 5 and 40°C. Once the room temperature has reached the
setting value, the device stops to heat. The device will turn on again when
the room temperature drops 2 °C below the setting value. You can select the
heating mode using the button (6). The selected heating mode is indicated by
or on the device display. In mode, the device can heat up to 55 °C, while in
mode, it can heat up to 75 °C. Repeatedly press the button to set the
remaining operating time in hours, up to 24 hours. You can enable or disable
the child lock function by pressing and holding the child lock button (4) for
3 seconds. If a power failure occurs or the device is switched off using the
main switch, all settings will be reset, including the child lock. After
switching on, the default thermostat temperature setting is 25°C. When the
button is used to switch off the device, the thermostat and heating level
settings are retained, and the switch-off timer countdown continues to run.
With smartphone application. The mobile phone needs to be connected to the internet.
-
Scan the QR code (5. figure) with your smartphone then download and install the “Tuya Smart” application.
-
Select the country dialing number, enter your mobile phone number and press the “Get” button.
-
Enter the “Verification code” you got in the SMS and enter the password you want to use in the application, which should consist of numbers and letters.
-
Log in to the application: „Login”
-
Make sure your appliance and smartphone are as close as possible to the wifi router and that both are connected to it.
-
Add the new appliance to the program by pressing the “+” button.
● Select the appliance type: “Heater”.
● Press the “Finish network configuration” button.
● Press and hold the button for more than 5 seconds until the beep sound
● Tick the check box, and press the „Next: Connect appliance with Wi-Fi” button
● Enter the Wi-Fi password, and press the „Confirm” button.
● Press and hold the button for more than 5 seconds until the beep sound.
The appliance is connecting the cloud-based application. -
If the connection under the 6. point was not successful, “Failed to add” is displayed.
● Choose the lower „Add appliance with other methods” possibility.
● Press and hold the button for more than 5 seconds until the beep sound.
● Press the „Finish network configuration” button.
● Tick the check box, and press the „Next: Connect appliance with Wi-Fi” button
● Enter the Wi-Fi password, and press the „Confirm” button.
● On the appearing „Connect phone to appliance’s wifi hotspot” screen, choose the „Connect now” option.
● Press and hold the button for more than 5 seconds until the beep sound, until the WLAN network shows up on the „SmartLifeXXXX” network. Choose this for the connection. If the status is „Connected”, then press the step back button on the mobile.
● The „Connecting now” screen runs down, and the appliance is connected to the cloud-based application. -
In the application, you can see the room temperature, you can switch on/off the appliance, you can choose the low (Low) or high (High) heating stage, and you can switch the child lock on/off, you can set switch off timing, and you can set the exact times and dates for switching the appliance on and off.
In the event of overheating, the overheating protection function will switch off the appliance, for example when the air inlets and outlets are covered. Power off the appliance by unplugging it from the electric outlet. Allow the appliance to cool (for at least 30 minutes). Check whether the air inlets and outlets are obstructed or not, and clean them if necessary. Install the appliance again. If the overheating protection activates again, power off the appliance by unplugging it from the electric outlet and contact the service facility.
SPECIFICATIONS
power supply: …………………………………….. 230 V~ / 50 Hz
output:……………………………………………….. 850 W
IP protection: ……………………………………… IPX4: Protected against splashing water, from
every direction!
dimensions of heater: ………………………….. 47 x 122 x 7 cm
transmission frequency/output: ……………… 2,4 GHz / 1 mW
weight: ………………………………………………. 14 kg
length of power cable: …………………………. 1,4 m
producer: Somogyi Elektronic Kft.
H – 9027
www.somogyi.hu
Distribútor: Somogyi Elektronic Slovensko s. r. o.
Ul. gen. Klapku 77, 945 01 Komárno, SK,
Tel.: +421/0/35 7902400
www.somogyi.sk
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>