Byybuo SmartPad A10 Tablet User Manual
- June 5, 2024
- Byybuo
Table of Contents
Byybuo SmartPad A10 Tablet
Package contents
- 1x Tablet BYYBUO
- 1x charger
- 1x documentation kit
- 1xUSB
Getting started
Charge the battery of your device
Connect the AC adapter to a grounded electrical outlet.
Note: Charge your byybuo device before using it for the first time.
WARNING!
Read the following instructions carefully about the battery of your byybuo
device
- Only a technician authorized by byybuo is allowed to remove and handle the battery
- The battery in your byybuo device may present a fire or burn hazard if removed or disassembled
- Respect the information on the warning labels of the device to avoid any risk of injury
- There is a risk of explosion if the battery is replaced by an incorrect model
- Do not dispose of the battery in a fire
- Do not attempt to short-circuit the byybuo battery.
- Do not attempt to disassemble the battery or reassemble the battery
- Stop using the battery if it is leaking
- The battery and its components must be recycled or disposed of properly.
- Keep the battery and its components out of reach of children
Turn on/turn off your device
Turn on your device by pressing and holding the power button.
Turn off your device:
- Open the Start menu
- Press the Stop button.
Presentation of the device
warning
- The lightning flash with an arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of an uninsulated “dangerous test” inside the product, which is of sufficient magnitude to constitute a risk of electric shock.
- In the documentation supplied with the device, the exclamation point within an equilateral triangle is intended to alert the user to the presence of important instructions regarding use and maintenance.
- At full volume, prolonged listening to the portable audio device can damage the user’s hearing.
Legal notice and copyright notice
This product has been manufactured and sold under the responsibility of
byybuo. All other trademarks and logos are property of their respective
owners. Made in RPC
FCC ID:2AXUI-A10
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. changes or
modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception,which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
SAR tests are conducted using standard operating positions accepted by the FCC with the device transmitting at its highest certified power level in all tested frequency bands, although the SAR is determined at the highest certified power level, the actual SAR level of the device while operating can be well below the maximum value, in general, the closer you are to a wireless antenna, the lower the power output. Before a new model device is a available for sale to the public, it must be tested and certified to the FCC that it does not exceed the exposure limit established by the FCC, Tests for each device are performed in positions and locations (e.g. at the ear and worn on the body)as required by the FCC. For body worn operation, this model device has been tested and meets the FCC RF exposure guidelines when used with an accessory designated for this product or when used with an accessory that Contains no metal Non- compliance with the above restrictions may result in violation of RF exposure guidelines.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>