401637 LED-Strip with Motion Sensor User Manual

401637 LED-Strip with Motion Sensor

Parts listing/Box contents

1. LED strip 1,2m
2. Driver
3. PIR sensor
4. 3m adhesive tape

Sensor information:

1. When it’s dark, the strip will light up once someone enters into the sensor area.
2. When it’s light the stripe will not turn on.

Technical details:

• Sensor detection distance 3m
• Turn-off delay time  Adjustable 10 ~ 260s
• Sensor detection angle 120°
• LED chips sm□352B
• Color temperature Extra warm white 2200K

Installation description

1. make the stick region clean, ensure the places are dust and oil free, release the paper from the 3m tape and stick the strips.
2. Use the cable connector to connect the Pl R sensor with the LED strip.
3. Fix the PIR sensor on the side of the bed and unblock the sensor.
4. Connect the driver with the cable connector and plug the driver into the socket.

Adapting/ trimming the LED strip
Attention! Before you trim the LED strip, make sure that you have disconnected the strip from the controller.

The flexible LED strip can be trimmed every 10cm. The correct spot for trimming, is indicated with the symbol of a pair of scissors.

Notes on Disposal
The product is designated for a separate collection at an appropriate collection point.
Do not dispose of the product with household waste. For more information, contact the retailer or the local authority responsible for waste management.

CARE

Before cleaning the unit, disconnect it, if necessary form other components; do not use aggressive cleaning agents. The unit has been carefully checked for defects. If nevertheless, you do have cause for complaint, please go back to the retailer where you have bought the product together with your proof of purchase. We are not liable for damage arising from incorrect handling, improper use or wear or tear. We reserve the right to make technical modifications.

Safety

General Safety

• Read the manual carefully before use. Keep this manual for future reference.
• Only use the product for its intended purposes. Do not use the product for other purposes than described in the manual.
• Do not use this product if any part is damaged or defective. If the product is damaged or defective, replace the product immediately.
• This product shall not be used by children without the supervision of an adult. Children shall not play with the device.
• Do not modify the product in any way.
  • Do not expose the product to water or moisture. (IP 20)
  • Do not immerse the product in water. (IP 44-IP 67)
• Keep the product away from heat sources.
• Do not block the ventilation openings.
• Do not look directly into the LED lamp.
• Keep a minimum distance ofl meter between the lamp and the surface being illuminated.

Electrical safety

• To reduce the risk of electric shock, this product should only be opened by an authorized technician when service is required.
• Do not use the product if the cable or plug is damaged or defective. When damaged or defective, it must be replaced by the manufacturer or an authorized repair agent.
• Before use, always make sure that the voltage is the same as the voltage on the rating plate of the device.
• Make sure that the cable does not hang over the edge of a worktop and cannot be caught accidentally or tripped over

Warning

• The lignt source contained in this luminaire shall only be replaced by the manufacturer or his service agent or a similar qualified person.
• Caution, risk of electric shock.
• The external flexible cable or cord of this luminaire cannot be replaced; if the cord is damaged, the luminaire has to be destroyed.

Disclaimer
Designs and specifications are subject to change without notice. All logos, brands and product names are trademarks or registered trademarks or their respective holders and are hereby recognized as such.

Documentation
The product has been manufactured and supplied in compliance with all relevant regulations and directives, valid for all member states of the European Union. The product complies with all applicable specifications and regulations in the country of sales.
Formal documentation is available upon request. The formal documentation includes, but is not limited to the Declaration of Conformity, the Material Safety Data Sheet and the product test report.

CE declaration
This product complies with the following directives:

• LVD: 2014/35/EU
• EMC: 2014/30/EU
• RoHS: 2011/6S/EU
• Additionally, for Products with Radio transmitter units:
• RED: 2014/53/EU
• The complete Declaration of Conformity Document (DOC) can be found here:
• http://www.shada.nl/uploads/DoCs/index.html

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>