eta Super Sonic Stick Vacuum Cleaner Instruction Manual

eta Super Sonic Stick Vacuum Cleaner Instruction Manual

eta Super Sonic Stick Vacuum Cleaner

INSTRUCTIONS FOR USE

Dear customer, thank you for purchasing our product. Please read the operating instructions carefully before putting the appliance into operation and keep these instructions including the warranty, the receipt and, if possible, the box with the internal packing.

I. SAFETY WARNING

GENERAL PROVISIONS:

• Consider the instructions for use as a part of the appliance and pass them on to any other user of the appliance.
• Check whether the data on the type label corresponds with the voltage in your socket. The power cord plug may only be connected to the electrical socket complying with the applicable standards.
• This appliance may only be used by children aged 8 years or older, and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision. Children younger than 8 years must be kept out of reach of the appliance and its power cord.
• If a vacuum cleaner can be equipped with a hand–held accessory with rotating parts a warning has to be given concerning entrapment.
• Never use the appliance if its adaptor or plug is damaged, if it does not work properly, if it fell down and was damaged. In this case take the appliance to a special service to check its safety and proper function.
• Never immerse the charger, the battery and the motor part of the vacuum cleaner into water (even partially) and protect them against humidity!
• Switch off the device prior to any handling of the containers (B, L2, L5) or technical maintenance.
•  Never leave the product unattended when in operation!
• Do not charge the battery if electrolyte is leaking from it.
• The appliance must be disconnected from the power adapter when removing the battery.
• Do not through the battery into fire. There is a risk of explosion!
• In order to ensure safety and proper function of the appliance, use only original spare parts and accessories approved by the manufacturer.
• Only use this appliance for the purpose it was designed for, as specified in this manual. Never use the appliance for any other purpose.
• The manufacturer is not responsible for damage caused by improper use of the appliance and the accessories and its warranty for the appliance does not apply in situations when the safety warnings above are not complied with. Failure to replace or maintain all filters regularly according to the instructions in Chapter IV., V., VI and also using non–original filters, the properties of which resulted in failure or damage of the vacuum cleaner, is also understood to be improper use of the appliance.

USE OF THE APPLIANCE:

• The product is intended for home use and similar (in shops, offices and similar workplaces, in hotels, motels and other residential environments, in facilities providing accommodation with breakfast). It is not intended for commercial use!
• Avoid contact with the rotating brush when handling the vacuum cleaner (e.g. with loose clothes, hair, fingers, jewellery, bracelets etc.).
• Do not leave the floor nozzle with the rotation brush on in one place for too long! It could cause damage to the surface vacuumed!
• The floor nozzle with the rotation brush is not intended for vacuuming impurities from carpets with high pile.
• Do not use mopping adapter L for dry cleaning.
• When the floor is made of parts or contains wooden parts, it has to be completely sealed against water leaks. The cleaned surface has to be resistant to spilled water.
• The Manufacturer is not liable for any damages caused by water leaking into the floor and shall not participate in any compensation for such damages.
• Mopping adapter L is intended for cleaning hard flooring materials only (e.g. wood linoleum, vinyl, floor tiles, parquet flooring, floating floor and similar). Not intended for vacuum cleaning of the dirt on carpets.
• Never use the vacuum cleaner nor touch the adaptor with wet hands or feet!
• Always switch off the vacuum cleaner when charging the battery and after the vacuum cleaner was used.
• Do not vacuum wet or moist floor coverings, do not use the vacuum cleaner for outdoor areas! When moisture gets into the aggregate, there is a risk of its damage and disabling it. This defect is not covered by the warranty.
• Do not vacuum water, liquid or aggressive liquid!
• Do not vacuum sharp objects (e.g. glass, shatter), hot, flammable, explosive items (e.g. ash, hot cigarette butts, gasoline, thinners and aerosol vapours) or greases (e.g. fats, oils), caustic agents (e.g. acids, solvents). Vacuuming these objects may lead to damage of the dust filters or the vacuum cleaner.
• Pores of the micro filters may be clogged when vacuuming very fine dust. Thus, air permeability will be reduced and the suction performance will drop. In this case, micro–filters have to be cleaned before the container is full. Do not use the vacuum cleaner to vacuum dirt produced during/after construction such as plasterboard dust, fine sand, cement, dust from construction, parts of plaster etc. If this dirt / loose construction materials / loose construction materials into the aggregate, it poses a danger of damage. The warranty repair does not cover this.

ACCESSORIES AND ASSEMBLY OF THE APPLIANCE:

• Install the vacuum cleaner and the appliance within sufficient distance from flammable objects (e.g. curtains, drapes, wood, etc.), heat sources (e.g. oven, stove, etc.) and wet surfaces (e.g. sinks, wash–basins etc.).

ADAPTER:

•  If the adaptor of the appliance is corrupted, it has to be replaced by the manufacturer, its service technician or a similarly qualified person so as to prevent dangerous situations.
• WARNING: To charge the battery, use only the network adapter supplied with this appliance.
• To power the appliance, only apply safe small voltage in accordance with the type plate.
• Use the charger in a room only.
• The adaptor supplied with this appliance is intended for this appliance only, do not use it for other purposes.
• The power cord must not be damaged with sharp or hot objects, open fire, it must not be sunk into water or bent over sharp edges.

For trouble-free operation of the vacuum cleaner, please use the tested

micro-filters recommended by the producer.

II. EQUIPMENT AND ACCESSORIES (Fig. 1)

A – vacuum cleaner

A1 – ON/OFF button
A2 – continuous operation switch
A3 – maximum performance button
A4 – operation signal lights and charging lights
A5 – container lock button
A6 – output HEPA filter locking button
A7 – output HEPA filter
A8 – handle
A9 – charging connector

B – dust container

B1 – hinged bottom
B2 – hinged bottom locking button
B3 – fabric input filter
B4 – separator

C – battery

C1 – battery locking button
D – extension attachment for accessories
D1 – metal suction tube
D2 – flexible suction hose
D3 – short suction tube with a joints
D4 – metal suction tube with a joint
D5 – joint
D6 – joint lock
D7 – attachment locking buttons
Ea – floor nozzle with rotation brush
Ea1 – floor nozzle lock button
Ea2 – LEDs illuminating the space in front of the vacuum cleaner
Ea3 – removable brush
Ea4 – brush lock
Eb – floor nozzle with rotation brush
Eb1 – floor nozzle lock button
Eb2 – LEDs illuminating the space in front of the vacuum cleaner
Eb3 – removable brush
Eb4 – brush lock

F – cushion nozzle

F1 – brush locking button
G – brush 1
H – brush 2
I – crevice nozzle
J – long crevice nozzle
K – small turbo brush
L – mopping adapter
L1 – mopping adapter locking button
L2 – water (detergent) tank
L3 – water tank (K2) locking button
L4 – swing-out plug
L5 – dirt container
L6 – dirt container (K5) locking button
L7 – suction chamber
L8 – check float
L9 – closure
L10 – upper removable section
L11 – screws
L12 – additional spraying on/off button
L13 – additional spraying pilot lamp
L14 – swing-out lid lock
L15 – brush cover lock
L16 – swing-out cover
L17 – brush cover
L18 – brush
L19 – drip tray

M – adapter
N – plastic wall bracket
O – screws
P – wall plugs

III. VACUUM CLEANER PREPARATION

Remove all packing material, take out the vacuum cleaner and the accessories. Remove all possible adhesion foils, stick-on labels or paper from the appliance.

VACUUM CLEANER ASSEMBLY

When assembling the vacuum cleaner, follow the procedure indicated in Fig. 1a/1b. Select appropriate accessories (Fig. 7) depending on the required use. For disassembly, proceed the other way round and release the locks.

CHARGING THE ACCUMULATOR

Turn the vacuum cleaner off prior to charging! Connect the adaptor to the charging connector A9 and plug it to the mains. The accumulator has to be charged at least for
8 hours prior to the first use. After that, the standard charging time is approx. 4 hours. The status and progress of charging is indicated by indicator A4.

Operation signal lights and charging lights (A4)

Operation signal lights and charging lights (A4)

Flashing red (approx. 15 seconds)| Battery discharged (the device will switch off)
Flashing red (approx. 8 seconds or as long as button A1 is pressed)| Clogged input filter B3 (suction system clogged)
Flashing red (until the device has been switched off)| Rotation brush electronic protection (rotation brush locked – rotation stopped, the drive continues running)
Flashes blue| Accumulator is charging.
Blue light on continuously| Accumulator is charged (after approx. 2 minutes, the signal lights will go out) / indication of operation

Warning

• Let the vacuum cleaner recharge as soon as its suction performance is  weaker.
• When using the vacuum cleaner for an extended period of time or in a hot environment, the accumulator might be too hot for Let the accumulator cool down prior to charging.

OPERATING TIMES

Set

power

|  | Running Time *|
---|---|---|---
ETA0231| ETA1231| ETA2231| ETA5231*
MIN| Approx. 25 minutes| Approx. 40 minutes| Approx. 25 minutes| Approx. 25 minutes
MAX| Approx. 15 minutes| Approx. 24 minutes| Approx. 15 minutes| Approx. 15 minutes
Note:** The stated operating times are based on ETA‘s internal testing and only apply to a new and fully charged battery. Depending on the age and wear of the battery, the operating time decreases.

MOUNTING THE PLASTIC BRACKET TO THE WALL

Mount the plastic bracket N to the wall using the fastener included or a similar fastener provided by you.

Caution

– Make sure that the el. socket is close to the mounted plastic bracket.
– Make sure that no electricity, telephone or water lines etc. are routed under the plaster near the area where the plastic bracket is mounted to the wall.

IV. USE OF VACUUM CLEANER (Fig. 7)

Let the vacuum cleaner charge sufficiently prior to using. CONTROL ON/OFF button (A1)
– press and hold the button to switch the vacuum cleaner on
– release the button to switch the vacuum cleaner off

Continuous operation switch (A2)

– when the switch is placed in the “” position, continuous operation of the vacuum cleaner is activated
– when the switch is placed in the “” position, continuous operation of the vacuum cleaner is deactivated

Maximum performance button (A3)

– when pressed once, the vacuum cleaner will deliver maximum performance (if the vacuum cleaner is switched on)
– when pressed twice, maximum performance of the vacuum cleaner will be deactivated (if the vacuum cleaner is switched on)

Caution

When you are using the floor nozzle Ea/Eb and the rotary brush will get blocked, turn off the vacuum cleaner, remove the cause of the blocking (clean the rotary brush) and resume vacuuming.

MOPPING ADAPTER

Additional spraying on/off button (L12)
– the 1st pressing the button (hand/foot) – additional spraying on (pilot lamp L13 will light on)
– the 2nd pressing the button (hand/foot) – additional spraying off (pilot lamp L13 will light off)

Notes

– Switch off additional water spraying 1 minute before the end of cleaning at the latest and only remove the moisture remaining on the floor using vacuum cleaning function to avoid water dripping from the device during carrying the device.
– If there are any larger impurities on the floor (bits of soil, rocks etc.), remove them first. Then, you can start using the appliance.
– The mopping adapter is intended for cleaning the dirt on the floor using water, hence, switch on additional water spraying immediately after switching on the device.
– As soon as the maximum capacity of the dirt container L5 is exhausted, the safety mechanism will be activated. Additional spraying function and L18 brush drive will be switched off (electromotor of the vacuum cleaner continues running). Red signal light A4 on the device starts flashing. The device must be switched off and the dirt container must be emptied, then you can continue cleaning operation.
– If the mop adapter will be inclined towards the floor level too much (approx. 30°) during the cleaning operation, the safety function will be activated, i.e. additional spraying function and L18 brush drive will be switched off. After returning to correct working position, pre-set mop adapter function will be restored.
– As soon as the water in container L2 is used up, empty dust container L5.
– When using the mop adapter, DO NOT APPLY maximum suction power (risk of water penetration into the motor).
– Prior to placing the mopping adapter on the drip tray K19, ALWAYS disconnect the vacuum cleaner and store the mopping adapter separately to avoid overturning/fall of the device.

Instruction for use:

1. Open the tank lid L4 and pour clean water (warm or cold) into the water tank L2.
2. Then connect the vacuum cleaner A to the mopping adapter L (Fig. 1b).
3. Press the button A1 to switch on the vacuum cleaner. Press the button L12 to switch on additional water spraying function.
4. Clean the floor using slow forward and backward movements.
5. Stop the device if water level in the dirt container L5 has reached the mark MAX. Empty the dirt container and install it on the device again. Continue cleaning.
6. After cleaning, switch off the vacuum cleaner and disconnect it from the mopping adapter. Then place the mopping adapter on the drip tray L19

V. REMOVING DUST CONTAINER, FILTERS, WATER TANK, DIRT CONTAINER

DUST CONTAINER REMOVAL (B)

When taking out the dust container B follow the procedure indicated in Fig. 2. Dispose of dirt contained in the dust container with regular household waste. An emptied and cleaned container is to be put back into the vacuum cleaner in reverse order.

INPUT FILTER REPLACEMENT (B3)

To remove the input filter, follow the procedure indicated in Fig. 2. To fit a new input filter in the vacuum cleaner, proceed in reverse order.

REPLACING THE HEPA FILTER (A7)

When removing the HEPA filter, proceed according to Fig. 3. Insert the new/clean HEPA filter into the vacuum cleaner in a reverse order.

WATER TANK (L2)

When removing the water tank L2 , follow the procedure shown on Fig. 1b. Install the water tank using the reverse procedure.

DIRT CONTAINER (L5)

When removing the dirt container L5 , follow the procedure shown on Fig. 1b. Dispose the dirt in the container into waste drain. Install the container using the reverse procedure.

VI. CLEANING AND MAINTENANCE

Notes

• For hygienic purposes we recommend that you empty the container and clean the filters after each use.
• Maximum suction power can be achieved when the filters are clean and the dustbag is empty.
• Every time you empty the dust container, we recommend that you also clean the filters.
• When you are vacuuming very fine dust, the filter pores might get clogged. This reduces the air flow and reduces the suction power. In such a case, the filters need to be cleaned even though the container is not full yet.

Clean the surface of the vacuum cleaner and adaptor with a soft wet cloth. Do not use any rough and aggressive detergents!

Accessories

After any vacuuming it is recommended to check visually the brushes or collectors for possible impurities. If there are some impurities, remove them.

Floor nozzle with rotary brush

Remove any dirt (especially hair, animal hairs, etc.) stuck to the brush. To make cleaning easier, the brush can be removed (Fig. 4).

Small turbo brush

Remove any dirt (especially hair, animal hairs, etc.) stuck to the brush

Dust container

Clean the surface and the inside of the container B with a soft wet cloth. Rinse the separator B4 under running water. Allow all the parts to dry out properly before their re-use.

Caution

Never rinse the container B under running water and never immerse it in water. It houses electrical components which drive the brush in the floor nozzle Ea/Eb and they might get damaged.

HEPA filter

Shake out the input HEPA filter A7 gently, or blow it out. If the HEPA filter is very dirty, you can rinse it under running lukewarm water. Allow it to dry out properly.

Caution

• Do not clean the filters with any aggressive washing or cleaning detergents or hot water.
• If you clean the HEPA filter with water, its filtration properties will deteriorate. The filter cannot be washed more than three times. After that, a new filter needs to be purchased.
• We recommend that you replace the HEPA filter twice a year.
• The filters are not dish-washer safe.
• Failure to clean or replace the filters as required may cause a defect of the vacuum cleaner!

Mopping adapter

Use fine and damp cloth for cleaning the surface of the mopping adapter. For a thorough maintenance, the adapter can be disassembled (Fig. 1b). Rinse the tank L2 and the container L5 with water. Rinse plastic parts L7, L9, L17 and the brush L18 in flowing water. Thoroughly remove the dirt assembled under the swing-out cover L16. Allow all parts to dry thoroughly before re-assembling.

L18 brush cleaning function:

1. Empty dirt container L5.
2. Fill L2 tank with clean water.
3. Place mop adapter L with the vacuum cleaner connected to drip tray L19. Switch on the vacuum cleaner and the additional spraying function.
4. Allow the water in tank L2 to drain. In case of heavy dirt, this process can be repeated.
5. Clean the other parts of the mop adapter in a standard way.

CAUTION

During the entire time of cleaning the brush, the mop adapter with attached vacuum cleaner must be held in the drip tray L19 to avoid the fall!

VII. ENVIRONMENTAL PROTECTION

If the dimensions allow, there are labels of materials used for production of packing, components and accessories as well as their recycling on all parts. The symbols specified
on the product or in the accompanying documentation mean that the used electrical or electronic products must not be disposed of together with municipal waste. For proper disposal of the product, hand it over at special collection places where it will be received free of charge. Suitable disposal of the product can help to maintain valuable natural resources and to prevent possible negative impacts on the environment and human health, which could be the possible consequences of improper waste disposal. Fines can be imposed for improper disposal of this type of waste in agreement with the national regulations. The appliance is equipped with the Li-Ion battery with long life. For environmental protection it is necessary to remove the battery from the appliance after its service life and the battery and the appliance must be disposed of safely using special collection networks. Ask for more details at the local authority or at the local waste collection site.

Removing the accumulator

To remove the battery, follow the instructions indicated in Fig. 5.]

VIII. TECHNICAL DATA

Protection class III.
Accumulator 21.6 V Li-Ion
Weight (kg) approx. (hand vacuum cleaner / stick vacuum cleaner) (1.4 / 2.5)
Size of the product (mm) (hand vacuum cleaner) 320 x 110 x 230
Size of the product (mm) (stick vacuum cleaner) 235 x 250 x 1100
Size of the product (mm) (mopping adapter) 265 x 240 x 825
ETA0231: Acoustic noise level of 72 dB(A) re 1pW
ETA1231: Acoustic noise level of 79 dB(A) re 1pW
ETA2231 + ETA5231: Acoustic noise level of 78 dB(A) re 1pW

Charging adapter

Manufacturer’s name or trademark, business registration number and address| ETA
Model identifier| YLS0241A-E260060
Input voltage| 100-240 V (AC)
Input frequency| 50/60 Hz
Output voltage| 26 V (DC)
Output current| 0.6 A
Output power| 15.6 W
Average efficiency in active mode| 86.96 %
Low load efficiency (10%)| 72.75 %
Power consumption without load| < 0.1 W
Appliance protection class| II.

The manufacturer reserves the right to change the technical

specifications and accessories for the respective models.

Guarantee of 24 months does not apply to decrease in the accumulator’s effective capacity caused by its use or age. Effective capacity gradually decreases depending on the method of use of the accumulator.

Replacement of parts that require intervention in the electric part of

the appliance must be carried out by a specialized service! Failure to comply with the instructions of the manufacturer will lead to expiration of the right to guarantee repair!

WARNINGS AND SYMBOLS USED ON THE APPLIANCE, PACKAGING OR IN THE

INSTRUCTIONS MANUAL:

HOUSEHOLD USE ONLY; DO NOT IMMERSE IN WATER OR OTHER LIQUIDS;

TO AVOID DANGER OF SUFFOCATION, KEEP THIS PLASTIC BAG AWAY FROM BABIES AND CHILDREN. DO NOT USE THIS BAG IN CRIBS, BEDS, CARRIAGES OR PLAYPENS. THIS BAG IS NOT A TOY.

The symbol indicates a
WARNING. – Please read the instructions manual –
Removable power supply unit

Read More About This Manual & Download PDF:

References

• AEG Hausgeräte | Setzen Sie auf Qualität | AEG
• ETA - tady je doma
• ETA - tu je doma

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>