MINOSTON MT11N Countdown Timer Switch Instruction Manual
- June 5, 2024
- Minoston
Table of Contents
MINOSTON MT11N Countdown Timer Switch
Specifications:
- Model: MT11N
- Incandescent Load: 960W
- Power: 120VAC, 60Hz
- Tungsten: 1200W
- Resistive: 1800W
- Motor: 1/2 HP
- Time Delay: 1m / 5m / 10m / 15m / 30m / 1hr
- Humidity: 95% RH, non-condensing
- Temperature Range: 32° F~104° F
Indoor use in dry location
DESCRIPTION
The MT11N is a timer switch with 6 preset time buttons and 1 Manual ON /OFF button. All Loads connect to this timer will automatically turn OFF when the selected time expires. The 6 selectable times are 1 Min, 5 Min, 10 Min, 15 Min, 30 Min, and 1 Hours.
FEATURES
- Easily replaces a standard single pole Light or Fan switch.
- Compatible with most types of lights.
Installation
How to use it?
- Preset Buttons: Press the button then LED indicator flashes 2 times.
- There are 6 buttons with preset times of 1 Min, 5 Min, 10 Min, 15 Min, 30 Min, and1 Hour.
- Press and release the “on” button, you can adjust required countdown time.
- When the Load is OFF, press and release the “on” button can adjust required time, once the time is over, the Load turn off automatically.
- When load is OFF, press the release “on” button, currectly the time is last selected timer preset.
- Keep the load is ON, hold the “on” button for 3s, no change, if you press this button again, the device will clear preset timer.
How to set up LED indicator brightness?
HOW TO INSTALL THE WIRES
- Unscrew : Carefully turn the screw counterclockwise to leave enough space for the wire to be inserted. Do not unscrew the screws completely.
- Press down: Once loosened, use your finger so it catches the thread.
- Insert the wire: Make sure the wire is completely straight, then insert it into the terminal while holding down the screw. Do not wrap the wire around the screw!
4. Tighten : Turn the screw clockwise to tighten the wire. Make sure the wires are locked!
Note : There are 2 holes for each terminal can be used in the connection. You can use a jump wire or the second hole at the
terminal to connect.
Ground
- Line (hot) — black (connected to power)
- Neutral — white
- Load — black (connected to lighting)
WARNING
Read and understand these instructions before installing. It is recommended
that a qualified electrician performs this installation. Make sure to turn off
the circuit breaker or fuse(s) and make sure power is off before wiring the
device.
This device is intended for installation in accordance with the National
Electric Code and local regulations.
Single Pole Wiring **
**
- Tool: Please prepare a flat head screwdriver.
- Turn power OFF at circuit breaker or fuse box.
- Remove wallplate.
- Remove the switch mounting screws.
- Disconnect the wires and label them after remove the old switch. (Please use our sticker)
- Carefully remove the switch from the switch box. (DO NOT disconnect the wires.)
- There are up to five screw terminals on the smart switch, these are marked (Please check
) - Fix the wallplate with screws after wiring succeed. (Please use our screws.)
- The Ground was excluded from the diagram to simplify the illustration. Please Make sure all ground wires are connected to all switches respectively.
FCC
This device complies with part 15 of the FCC and Industry Canada license-
exempt RSS standard(s). Operation is subjected to the following two
conditions:
- This device may not cause harmful interference,
- This device must accept any interference received, including interference that may cause undesired operation.
FCC NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment.
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio / TV technician for help.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
Important note: To comply with the FCC RF exposure compliance
requirements, no change to the antenna or the device is permitted. Any change
to the antenna or the device could result in the device exceeding the RF
exposure requirements and void user’s authority to operate the device.
WARRANTY
CAUTION – PLEASE READ!
This device (MT11N) is intended for installation in accordance with the
National Electric Code and local regulations in the United States, or the
Canadian Electrical Code and local regulations in Canada. If you are unsure or
uncomfortable about performing this installation consult a qualified
electrician.
WARNING – SHOCK HAZARD
Turn off the power to the circuit for the switch and lighting fixture at the service panel (circuit breaker) prior to installation. all wiring connections must be made with the power off to avoid personal injury and/or damage to the switch.
OTHER WARNINGS
- Risk of Fire
- Risk of Electrical Shock
- Risk of Burns
Our Products warrants this product to be free from manufacturing defects for a period of one year from the original date of consumer purchase. This warranty is limited to the repair or replacement of this product only and does not extend to consequential or incidental damage to other products that may be used with this product. This warranty is in lieu of all other warranties, expressed or implied. Some states do not allow limitations on how long an implied warranty lasts or permit the exclusion or limitation of incidental or consequential damage, so the above limitations may not apply to you. This warranty gives you specific rights, and you may also have other rights which vary from state to state.
Please contact us if you have any questions: ask@minoston.com , ask@minoston.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>