C3 Food Processor Fruits Instructions

scandinavian
lifestyle

INSTRUCTIONS

C3 FOOD PROCESSOR

Congratulations on choosing the C3 Food Processor. You have bought a quality product that you will be able to use and enjoy for many years.

IMPORTANT SAFEGUARDS

When using electrical appliances, basic safety precautions should always be followed, including the following:

1. Read and keep all instructions.
2. Do not use outdoors.
3. Ensure the mains voltage must corresponds to the voltage as shown on the rating plate.
4. To prevent against electric hazards, do not immerse the cord, plug or the motor body in water or any other liquid.
5. Close supervision is necessary when any appliance is used by or near children.
6. This appliance is intended to be used in household and similar applications such as: staff kitchen areas in shops, offices and other working environments; farm houses; by clients in hotels, motels and other residential type environments; bed and breakfast type environments.
7. Unplug from the wall outlet when not in use, or before putting on or removing parts, or before cleaning.
8. If the supply cord is damaged, it must be replaced by the manufacturer or a similarly qualified person in order to avoid a hazard. Do not operate the appliance with a damaged cord or plug or after the appliance malfunctions, or has been damaged in any manner. Return the appliance to an authorized service facility for examination repair or adjustment.
9. The use of accessories or attachments not recommended by the manufacturer may cause hazards.
10. Keep utensils and hands away from the blade, or cutting disc, or any moving parts during use.
11. Never allow hair, scarves, strings, or clothing, etc. to hang down over the appliance when the appliance is in operation.
12. Do not leave the appliance unattended when in use.
13. Do not let cord hang over edge or table or counter, or touch hot surfaces.
14. Do not place the appliance on or near a hot gas or electric burner or in a heated oven.
15. Do not operate the appliance with wet hands.
16. Do not operate this appliance for more than 1 minute at a time, allow the motor to cool down between intervals. Do not operate the appliance without any load.
17. Ensure all parts are correctly assembled before plugging into the wall outlet.
18. Ensure the lid and the bowl are securely locked in place before the appliance is switched on. Never unlock the lid or the bowl when the blade or the cutting disc is still spinning.
19. Switch off the appliance before connecting or disconnecting from the wall outlet
20. Blade and cutting disc are very sharp, handle with extreme care and caution. Never touch the sharp edges with your fingers.
21. This appliance must be supplied through a residual current device (RCD) having a rated residual operating current not exceeding 30mA.
22. Do not use the appliance connected to an external timer or a separate remote control system.
23. Do not attempt to dislodge food or clean the appliance when the appliance is plugged in.
24. Do not use the appliance for other than its intended use.
25. Do not operate for more than 30 seconds when processing heavy loads. Let the motor cool down between intervals.
26. WARNING: To reduce the risk of fire or electric shock, do not attempt to dissemble the appliance. No user-serviceable parts inside. Repairs should be done by authorized personnel only.
27. This electrical device complies with the relevant safety regulations. Repairs are only to be carried out by an authorized electrician. Improper repairs can lead to accidents and injury to the user.
28. This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children should be supervised to ensure that they don’t play with the appliance. Cleaning and user maintenance should not be made by children unless they are older than 8 and are supervised. Keep the appliance and its cord out of reach of children less than 8 years.
29. Do not put fingers or other objects into the feeding tube when the appliance is in operation.
30. Never push foods into the feeding tube with your fingers, always use the pushers provided.
31. If foods become lodged in the feeding tube or on the blade or the cutting disc, switch off the appliance and unplug. Then disassemble the unit and remove the lodged foods.
32. Never operate the appliance without the blade or the cutting disc in place.
33. This appliance has a safety interlock that stops the motor from operating unless both the lid and the bowl are locked in place. However, do not use the safety interlock as an on/off switch, always use the speed selector to switch off the appliance before unlocking the lid or the bowl.
34. To prevent hazards and damage to the appliance, never put over-sized or very hard foods in the feed tube.
35. Do not process hot liquids, cool to room temperature before putting it into the bowl.
36. The dicing kit is only for dicing soft foods. To prevent hazards and damage to the appliance, never use hard or frozen foods with the dicing kit.

      ![C3

• Prohibited 3](https://manuals.plus/wp- content/uploads/2022/05/C3-Prohibited-3.png)

SAVE THESE INSTRUCTIONS
HOUSEHOLD USE ONLY

| This marking indicates that this product should not be disposed with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact your local authority.
---|---

BEFORE USE

• Carefully read all instructions before using the appliance.
• Before the appliance is used for the first time, follow the section “CLEANING AND CARE”, disassemble and wash all parts in warm soapy water. Rinse and dry with a soft damped Never immerse the motor unit in water.
• Always ensure the appliance is unplugged from the wall when not in use, or during assembling or removing parts.

PARTS OF THE FOOD PROCESSOR

1. Small pusher
2. Large pusher
3. Feed tube
4. Lid
5. Locking tab
6. S-blade
7. Cutting disc (reversible slicing or shredding)
8. Bowl
9. Interlock catch
10. Handle
11. Spindle
12. Safety interlock
13. Motor unit
14. Speed selector

DICING KIT
Model 30-10112 only
15. Dicer pusher
16. Dicer feed tube
17. Dicer disc (12mm blade and julienne)
18. Dicer spindle

a 4mm shredding
b Reverse the disc for 3mm slicing
c PULSE= Burst of power
OFF = Off
LOW = Low speed
HI = High speed

HOW TO USE YOUR FOOD PROCESSOR

1. Ensure the appliance is unplugged and the speed selector (14) is at the OFF position.
2. Fit the spindle (11) onto the top center of the motor unit (13).
3. Fit the bowl (8) over the spindle (11) and align the arrow to the UNLOCK position. To lock the bowl (8) onto the motor unit (13), turn the handle (10) anti-clockwise until the arrow points to the LOCK position.
4. Choose either the S-blade (6) or the cutting disc (7) to fit over the spindle (11). Never attempt to fit both the S-blade (6) and the cutting disc (7) on the spindle (11) at the same time.
5. Place the lid (4) over the bowl (8) so that the locking tab is at the left of the handle (10). Hold by the feed tube (3) and turn the lid (4) anti-clockwise until the locking tab (5) slots into the interlock catch (9) of the handle (10).
6. Place the large pusher (2) into the feed tube (3), and then place the small pusher (1) into the large pusher (2).
7. Plug the unit into a 220-240V~ wall outlet.
8. The food processor is now ready for use.

| NOTE: This appliance has a safety interlock that stops the motor from operating unless both the lid (4) and the bowl (8) are correctly locked in place.
---|---

| CAUTION: Always handle the S-blade (6) and the cutting discs by the center plastic section only The edges on the blade and cutting discs are very sharp, handle them with extreme care and caution. Never touch any blades with your fingers. Keep blades away from children and pets.
---|---

PROCESSING WITH THE S-BLADE (6)

1. Place foods into the bowl (8) through the feed tube (3), alternatively, foods can be placed before fitting the lid.
2. Do not overfill the foods in the bowl (8) as it may overload the motor. Do not fill exceeding the MAX level marking.
3. Turn and release the speed selector (14) to PULSE 2 to 3 times or until you achieve the desired texture.
4. Switch to OFF when finished. Unplug from the wall outlet.
5. Unlock and remove the lid (4) by turning it clockwise.
6. Unlock the bowl (8) by turning the handle (10) clockwise until the arrow points to the UNLOCK position.
7. Remove the S-blade (6) by grasping the center plastic section.

PROCESSING WITH THE CUTTING DISC (7)

1. Use the cutting disc (7) (with the 4mm shredding cutters facing upward) for shredding cheese, carrots, potatoes and ingredients of a similar texture.
2. Alternatively, flip over the cutting disc (7) with the slicing blade facing upwards for slicing cheese, carrots, potatoes, cabbage, cucumber, beetroots and onions.
3. Switch on the motor by turning the speed selector (14) to LOW or HI.
4. Use both the small pusher (1) and large pusher (2) together for pushing down large foods into the feed tube (3). For small foods, first put the large pusher (2) into the feed tube (3), and then put foods through the hole of the large pusher (2) and push foods down using the small pusher (1).
5. Gently guide the food down the feed tube (3) using the pushers. Never force the food down as this will damage the cutting disc and causes hazards.
6. Switch to OFF when finished. Unplug from the wall outlet.
7. Unlock and remove the lid (4) by turning it clockwise.
8. Remove the bowl (8) by turning the handle (10) clockwise until the arrow points at the UNLOCK position.
9. Remove the cutting disc (7) by grasping the center plastic section.

| WARNING: Always use the pushers when pushing the foods down the feed tube. Never put your fingers or any other utensils into the feed tube. Always wait for the S-blade (6) or the disc (7, 17) to stop spinning before removing the lid (4).

WARNING: The cutting disc (7) is only compatible with the spindle (11) and the dicer disc (17) is only compatible with the dicer spindle (18). Never assemble the cutting disc (7) with the dicer spindle (18) or the dicer disc (17) with the spindle (11) as this will damage the appliance and causes hazards.

---|---

PROCESSING WITH THE DICING KIT (FOR MODEL 30-10112)

1. Use the dicing kit for processing diced foods.
2. Ensure the appliance is unplugged and the speed selector (14) is at the OFF position.
3. Fit the dicer spindle (18) onto the top center of the motor unit (13).
4. Fit the bowl (8) over the dicer spindle (18) and align the arrow to the UNLOCK position. To lock the bowl (8) onto the motor unit (13), turn the handle (10) anti-clockwise until the arrow points to the LOCK position.
5. With the 12mm blade facing upwards, fit the dicer disc (17) over the dicer spindle (18).
6. Place the lid (4) over the bowl (8) so that the locking tab is at the left of the handle (10). Hold by the feed tube (3) and turn the lid (4) anti- clockwise until the locking tab (5) slots into the interlock catch (9) of the handle (10).
7. Place the dicer feed tube (16) into the feed tube (3).
8. Plug the unit into a 220-240V~ wall outlet.

9. Switch on the motor by turning the speed selector (14) to LOW.
10. Place foods in the dicer feed tube (16) and gently push the food down using the dicer pusher (15). Foods will be cut vertically when being pushed down and then cut horizontally by the dicer disc (17).

| WARNING: The dicing kit is only for dicing soft foods such as potatoes, zucchini, avocados, ripe apple, bananas and kiwi, do not use it for dicing hard foods such as carrots and radish. Use of hard foods on the dicing kit will damage the appliance and causes hazards.
---|---

11. Switch to OFF when finished. Unplug from the wall outlet.

PROCESSING JULIENNE WITH THE DICER DISC (17) (FOR MODEL 30-10112)

1. Use the 8mm juliene disc for julienning cheese, carrots, potatoes and ingredients of a similar texture.
2. Flip over the dicer disc (17) with the julienne cutters facing upward and fit it over the dicer spindle (18).
3. Switch on the motor by turning the speed selector (14) to LOW or HI.
4. Use both the small pusher (1) and large pusher (2) together for pushing down large foods into the feed tube (3). For small foods, first put the large pusher (2) into the feed tube (3), and then put foods through the hole of the large pusher (2) and push foods down using the small pusher (1).
5. Gently guide the food down the feed tube (3) using the pushers. Never force the food down as this will damage the cutting disc and causes hazards.
6. Switch to OFF when finished. Unplug from the wall outlet.

PROCESSING TIPS

1. Use fresh foods for best result.
2. When shredding or slicing, don’t cut foods into too small pieces. Fill the food with the width of the feed tube fairly full. This prevents the food from slipping sideways during processing. Alternatively use the small feed hole of the large pusher.
3. When using the cutting discs, place foods horizontally for better result.
4. When crumbing bread, use dry bread as fresh bread sticks to the blade.
5. Add liquid to pureed foods after processing.
6. Add liquid through the feed tube to process mixtures.
7. When processing a variety of ingredients, it is not necessary to remove them from the bowl after each task, unless they exceed the MAX level marking.
8. When processing dry and wet foods together, the mixture will process more evenly if the wet ingredients are placed in the bowl first.
9. Pre-cut into 2cm cubes for softer structured foods (such as meat) and freeze them until just firm before processing.
10. For more uniform results, cut foods to approximately equal in size before processing with the S-blade. More consistent processing results are achieved if the bowl is not overloaded.
11. When processing large vegetables such as onions and potatoes, peel and cut into quarters or approximately 3cm cubes.
12. When foods stuck on the side of the bowl during processing, switch to OFF position and unlock the lid. Use a spatula to scrap off the foods on the side of the bowl and continue processing.
13. The dicing kit is only for dicing soft foods, do not use it for dicing hard or frozen foods. To prevent hazards and damage to the appliance, hard foods should be boiled to soft and cooled before dicing.

CLEANING AND CARE

1. Always switch off and unplug before cleaning and taking off parts.
2. Never immerse the cord, plug or motor unit in water or any liquid.
3. Wash all removable parts in warm soapy water. Rinse and dry thoroughly.
4. The parts are easier to clean immediately after use.
5. Wipe clean the motor unit with a soft damp cloth, add a little mild washing liquid if necessary.
6. The motor is permanently lubricated. Do not attempt to add any lubrication to it.

| WARNING: Blades and cutting discs are very sharp, handle with extreme care and caution. Never touch the sharp edges with your fingers.

WARNING: Do not place any parts in a dishwasher or use hot water to wash the parts as it may crack the plastics.

---|---

| NOTE: To avoid corrosion, rinse the blade immediately after it has been used on acidic or salty foods.
---|---

NOTES

Technical Data
Model: 30-10110 / 30-10111/ 30-10112
Voltage 220-240V ~ 50Hz
Output: 500W

For information or assistance
C3 Scandinavian Lifestyle AB
C/O iOffice, Kungsgatan 37, 111 56 Stockholm, Sweden
Tel: +46 (0)8 410 58 400
info@empirenordic.com

30-10110_30-10111_30-10112_ED05_KINNEX0521

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>