EVOLVEO N4 Baby Monitor Instructions
- June 5, 2024
- Evolveo
Table of Contents
EVOLVEO N4 Baby MonitorInstructions for the use of baby monitors
Thank you for buying our products, This manual provides you the monitor
information and methods of using the monitor.
Safety instruction
- this baby monitor is not a substitute for responsible adult supervision.
- this product shall be placed in a place that is not accessible to the baby and shall be kept in a distance of at least 1.5 m from the baby to ensure that the baby has a corresponding safe range with the product.
- DC power should not be placed where baby can touch, avoid to wind the child’s body parts and cause baby safety problems.
- this product is not a toy and children are not allowed to play with it.
- use the correct power adapter: output 5V/1A
Products Appearance
TX Camera
- Camera
- 2.power light
- IR sensor
- IR light
- Microphone hole
- Mat
- SPEAKER
- ANTENNA
- DC POWER PORT
- Pair code key
- temperature sensor
- Bracket
Handheld display
- Power port
- Power indicator and voice volume lamp
- boot Key
- Camera switching key
- Menu Key
- OK key
- direction key
- Music key
- Intercom key
- Reset Key
- Speaker
- Bracket
- battery cover
- antenna
- LCD
Button introduction
- Power On / off key: long press to turn on/off machine and short press to turn off the screen after boot
- Ok key: implement menu execution instructions
- Pair code key;Perform the pairing effect of the camera on the code
- Menu/return key: implement the pop-up of the menu, as well as the return of each submenu to the next level
- Up key: realize menu setting item up option scroll. And a quick increase in screen brightness.
- Down key: implement menu settings to scroll down options. And a quick decline in screen brightness.
- Left key: realizes the left movement of the menu setting item. And the quick decline of volume.
- Right key: realizes the right movement of the menu setting item. And the quick increase of volume
- Intercom key: in the monitoring screen, long-press this key to realizing the intercom function
- Camera switching key: achieve camera switching, lock a single camera monitoring, and achieve two camera cycle monitoring functions
- Music on / off shortcut key: quickly turn on and off music in the monitoring screen. When the music is turned on, the short press to switch the music.
- Reset key: once pressed the boot key is invalid and cannot be used normally. You can press the reset key lightly and then press the boot key to turn on normally.
TX camera
-
This machine uses DC adapter with output 5V/1A
-
Power the device on and the blue led indicator lights on, indicating that the machine is turned on and is working
Note: Use only the supplied power adapter. -
Night vision: the baby device has 10 infrared light, which are used to complement the light in the dark, and the user gets a clear image.
-
Turn on and off the infrared light: on working mode, the infrared light can be turned on and off automatically through the dark and bright light of the environment, so as to increase the amount of light fed by the camera and achieve the supplementary light effect in the dark state of the image, so that the user can view the best image.
-
please place this device within the range of baby monitoring, and the camera is aimed at the area you want to monitor. Don’t put the machine where the baby reaches out and get it, so as to avoid strangling the power cable to the baby and causing asphyxiation
-
If the image or sound is disturbed, try moving the device to a different location for debugging to the best effect。
-
when the first to use, you need to match it successfully before you can use it. For more information on pairing, see the details page for adding cameras to 2.5.5 cameras.
RX display
-
This machine is powered by a 3.7v lithium battery or a DC ad apter output of 5V/1A, The power Adapter can be used for charging when the lithium battery is low
Note: Use only the supplied power adapter. -
Turn on the device and long press the boot key ,then enter into the initial system screen.
-
This machine can support two cameras to monitor
-
The monitor screen icon is shown in the following figure
-
signal strength indication
-
The present camera icon (press the switch key to switch. 1 for the first camera and 2 for the second camera)
-
Locking a single camera monitor icon (press the switch key to switch, when switching to circular monitoring, the icon prompt will be changed. Switching to this icon it means circular monitoring)
-
The music icon , the device has 8 pieces of music totally, and the user selects #1 – 8 as a single loop, and if you select 9, all the music will be loop played.
-
speaker icon
-
temperature for baby room,
-
Time icon(AM means morning, PM means afternoon)
-
battery icon
-
Menu Option
The menu options are shown in the following figure Press menu/return key to the pop-up menu, which contains 6 items: Breast-feeding reminder setting -
Music selection setting
-
Time setting
-
Temperature setting
-
Camera setting
-
Voice control setting
-
You can select the menu by right or left key to move the Cursor, Press the up and down keys to make the selection. then Press the ok key to confirm. Press the menu/ return key to exit the setup menu
-
Breast-feeding reminder setting
Enter the feeding reminder setting, there are 5 alarms to choose from the following figure. Select the breastfeeding reminder setting up, press the up and down key to select, and then press OK key to confirm. (there are 6 sub- options for breastfeeding reminder settings: off and 5 time periods of an alarm clock) , the default is OFF -
Music selection setting
Enter the music settings item, there are 10 sub-options settings as shown below Select the music settings, press up and down key to select, then press OK key to confirm. (music settings have 10pcs sub-options: off, loop, and 8 pieces of music) the default is OFF -
Time setting Select the time setting, press up and down key to change the value, and press the ok key to move the cursor. Set the hours, minutes, seconds in turn. and AM, PM, press OK key to confirme
-
Temperature setting Select the temperature setting,it will appear Celsius and Fahrenheit two suboptions, use the top, lower keys to select, press ok key to confirm. Default to Fahrenheit
-
Camera selects the camera setting, there will be a loop, delete and add, three sub-options, use the up and down key to select when you press the ok key to select the loop settings item, and the three sub-options will pop up as follows Select by up and down key, and press the ok key to confirm (check the camera 1 means the camera 1 is locked in the monitor screen. select camera 2 means camera 2 is locked on the monitor screen. Select the loop item to mean the camera 1 and the camera 2 are in the monitoring screen by Cycle switching)When you select the deleted item, press the ok key to pop up the two sub-options as shown in the following figure Select by up and down key. Press the ok key to confirm (delete item means to delete the camera that has been paired successfully). it means the deletion is successful when the icon on the upper of the camera disappears.when the added item is selected to press the ok key. The two sub-options are shown as follows figure Use the up and down key to select, press the ok key to confirm, at this time the power indicator flashes. At the same time, press Pair code key in TX camera, the power indicator of the TX camera is also flashing when Pairing , a few seconds later matched successfully. When the pairing succeeds, the following figure When the pairing is successful, the icon appears the upper of the camera, After successful pairing the camera can be used, When the camera is out of range, it will lose contact. Entering the range again will automatically connect
Note : the camera has been matched at the factory, and there is no need to re- pairing unless they are out of touch. -
Voice control setting
Enter the voice control settings as shown in the following figure Select the voice control setting, press up and down key to select, pressing ok key will appear off, low, medium and high, four sub-options, then press up and down key to select, then press an OK key to confirm. The default is OFF,
Note: when one of the three items of low, medium, and high is selected, there is a corresponding icon appears at the top of the screen in the monitoring screen that shows the following figure) -
Focus note: about voice control sensitivity, in the viewing movie state, when the environmental sound of the TX camera is low to a certain value, the RX machine will turn off the screen and sound, when the environmental sound of the TX camera is high to at a certain value, the RX machine will be awakened.
Installation method
-
- put the TX camera on the working table at the corresponding height. where the baby can be monitored , and adjust the angle of TX camera.
- fixed with a three-foot bracket and adjust the angle.
Maintenance of Monitor
Keeping the lens clean can help you monitor the clearest picture. Gently wipe the fingerprints and dust on the lens and LCD screen by soft gauze.In order to avoid the danger of electric shock. Don’t open the machine or fix it by yourself. Keep the machine dry. Don’t use the machine in an environment that is too wet. If used in wet environment, it may cause machine failure.
Note: the right to change the design and specifications of this product is subject to change without prior notice
Disposal: The symbol of crossed out container on the product, in the literature or on the wrapping means that in the European Union all the electric and electronic products, batteries and accumulators must be placed into the separate salvage after finishing their lifetime. Do not throw these products into the unsorted municipal waste
DECLARATION OF CONFORMITY
Hereby, the company Abacus Electric, s.r.o. declares that the EVOLVEO Babby
monitor N4 is in compliance with the requirements of the standards and
regulations, relevant for the given type of device.
Find the complete text of the Declaration of Conformity at
ftp://ftp.evolveo.com/ce
Dovozce / Dovozca / Importer / Importőr
Abacus Electric, s.r.o.
Planá 2, 370 01, Czech Republic
Výrobce / Výrobca / Manufacturer / Gyártó
Naya Limited
No.5, 17/F, Strand 50, 50 Bonham Strand, Sheung Wan, Hong Kong
Made in China
Copyright © Abacus Electric, s.r.o.
www.evolveo.com
www.facebook.com/EvolveoCZ
All rights reserved. Design and specifications may be changed without prior
notice.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>