ENFORCER MVD-AH12-01Q 4K HDMI Splitters Instruction Manual

4K HDMI Splitters
Installation Manual

MVD-AH14-01Q shown

The ENFORCER 4K HDMI Splitters allow for one HDMI source to simultaneously transmit to up to four different monitors. The splitters work with most HDMI devices,  delivering the very best in digital audio and video signals with HD resolutions of up to 4K@60Hz. An LED indicator clearly displays power status as well as which outputs are active. The 4K HDMI Splitters can be daisy- chained up to four levels for even more outputs.

• Transmits an HDMI source to up to two (MVD-AH12-01Q) or four (MVD-AH14-01Q) different HDMI displays
• Additional splitters can be daisy-chained for more outputs
• HDR Support
• Supports up to 4K@60Hz resolution and 3D video
• Individual status LEDs for each HDMI output
• Two EDID management settings
• One 5VDC power supply included

HDMI, the HDMI Logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.

4K HDMI Splitters

Parts List

1x 4K HDMI Splitter
1x 5VDC Power supply
1x Manual

Specifications

(5m)
Video output connector| 2x HDMI Type A 19-pin female| 4x HDMI Type A 19-pin female
Max. output cable length| 24AWG: 50′ (15m); 26AWG: 32′ (10m); 28AWG: 16′ (5m)
Operating voltage| 5VDC
Power supply| 1A@5VDC (2.1mm plug)
ESD protection| ±8kV (air-gap discharge), ±4kV (contact discharge)
Current draw| 2W
Operating temperature| 32°~104° F (0°~40° C)
Operating humidity| 20~90% RH (no condensation)
Dimensions| 23/16″x315/16″x5/8″

(56x100x16 mm)

| 21/2″x67/16″x5/8″

(63x163x16 mm)

Weight| 6-oz (165g)| 9-oz (260g)

Overview

MVD-AH12-01Q

Overview (Continued)
MVD-AH14-01Q

Installation

1. Determine the location of where the 4K HDMI Splitter will be installed in relation to the HDMI source and HDMI displays.
2. Plug the HDMI source into the HDMI connector input on the splitter.
3. Plug the HDMI displays into the HDMI connector outputs on the splitter.
4. Plug the 5VDC adapter into the splitter.
5. Turn the HDMI source and displays on.
6. Adjust the EDID settings as necessary

EDID Management Settings

TV – Copy the display resolution from Output 1 to other Output displays.
1080p – Limit the resolution to 1080p.

Sample Application

MVD-AH14-01Q

Troubleshooting

HDMI Device does not function correctly.| • Make sure the splitter is powered.
• Make sure the source and display(s) are powered.
• Make sure that there are no problems with the HDMI source, HDMI cables, or HDMI display(s) by plugging a source directly into the display using the HDMI cables.
• Make sure that the source and display(s) are plugged into the correct connectors.
• Make sure the HDMI source is compatible with the HDMI display(s).
• Make sure the HDMI input and output cables are used within the specified range (see Specifications).
---|---

HDMI, the HDMI Logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.

FCC COMPLIANCE STATEMENT
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY
NOT CAUSE HARMFUL INTERFERENCE AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
Notice: The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, no change to the antenna or the device is permitted. Any change to the antenna or the device could result in the device exceeding the RF exposure requirements and void the user’s authority to operate the device.
IMPORTANT: Users and installers of this product are responsible for ensuring that the installation and configuration of this product comply with all national, state, and local laws and codes. SECO-LARM will not be held responsible for the use of this product in violation of any current laws or codes.
California Proposition 65 Warning : These products may contain chemicals that are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
WARRANTY: This SECO-LARM product is warranted against defects in material and workmanship while used in normal service for one (1) year from the date of sale to the original customer. SECO-LARM’s obligation is limited to the repair or replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM. This Warranty is void if the damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair or alteration, improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that such equipment is not operating properly as a result of causes other than defects in material and workmanship. The sole obligation of SECO-LARM and the purchaser’s exclusive remedy shall be limited to the replacement or repair only, at SECO-LARM’s option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or property damage of any kind to the purchaser or anyone else.
NOTICE: The SECO-LARM policy is one of continual development and improvement. For that reason, SECO-LARM reserves the right to change specifications without
notice. SECO-LARM is also not responsible for misprints. All trademarks are the property of SECO-LARM U.S.A., Inc. or their respective owners. Copyright © 2022
SECO-LARM U.S.A., Inc. All rights reserved.
SECO-LARM® U.S.A., Inc.

16842 Millikan Avenue, Irvine, CA 92606 Phone: 949-261-2999 | 800-662-0800

Website: www.seco-larm.com
Email: sales@seco-larm.com
PICHN3
MI_MVD_AH1x-01Q_211125.docx

References

• La Armería de Madrid - fabricantes de armas y rifles
• P65Warnings.ca.gov

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>