SHADA 240120X Water Resistant Luminaire with HF-Motion Sensor Instruction Manual

SHADA 240120X Water Resistant Luminaire with HF-Motion Sensor

LED’s light

Package contents

• 1x Water resistant luminaire with HF-sensor
• 1x Installation and Operating manual

1. Manual identification
   Shada B.V, 7328-JK Apeldoorn, Molenmakershoek 28, The Netherlands.
   www.shada.nl
   Release date: 20200424 12:03
   Article number: 240120X (X=1,2,3,4)

2. General
   This product is designed for outdoor and indoor use. It is equipped with a LED tube, an HF-motion sensor, polycarbonate housing, swivel, 2 stainless steel mount-ing brackets, 4 screws and 4 wall anchors.

3. Unique identification of the product
   Waterproof luminaire with HF-motion Sensor
   Article number: 240120X(X=1,2,3,4).
   The product meets the requirements of protection class 1.
   Level of protection IP65, dustproof, protected against water jets.
   Further technical data can be found in table 1. („TAB 1“ on page 3)

4. Modification of the product
   The product may not be changed or adapted. Do not use the product for other purposes than described in the manual.

5. Security related information
   Keep this product out of reach of children or animals. This product is not a toy, LED lights are extremely bright and looking directly at the light source during operation can lead to seri-ous eye damage. Any other use of the device than described in the manual may damage the product or cause danger to the user, e.g. due to a short circuit, fire or electric shock.
   The safety instructions must be observed at all times.

6.  Conformity of the product with legislation
   The warranty expires in the event of damage due to non-compliance with the safety in-structions of the device. Furthermore, we are not liable for consequential damage, damage to objects or persons resulting from failure to observe the safety instructions and improper use/handling of the device due to wear and tear. Product design and specifications are sub-ject to change without notice. All logos and trade names are registered trademarks of their respective owners and are hereby acknowledged as such.

7. Storage of the Manual
   Please read the operating instructions carefully and completely before use. The operating instructions are part of the product, they contain important information on the commission-ing and handling of the device. Keep all enclosed operating instructions for future reference. If the device is sold or passed on to third parties, you are obliged to pass on the operating instructions as these are lawfully part of the product.

8. Use of the product / Installation
   Before use, check the completeness of the parts supplied and the intactness of the product. If damaged, it must not be put into operation. This product may only be installed by a quali-fied technician.
   Installation:

9.  Decide where to mount the luminaire.

10. Disconnect from the mains.

11.  Secure against being switched on again.

12.  Verify that there is no voltage to your cable.

13.  Follow the enclosed steps. („Fig. 1“ on page 2)
    We can only ensure the correct function of the sensor when the product is mounted to the ceiling.

14. Operating the product
    The safety instructions and warnings must be observed to ensure both the perfect condition of the product and safe operation.

15.   Product maintenance
    The product can be cleaned with clear water and a soft cloth. Do not use detergents contain-ing surface active agents or scouring agents.

16.   Accessories, consumables, spare parts
    For this product there are led tubes available separately.

17. Information about special tools, devices
    You do not need any special tools to take this device into use.
    Depending on the mounting surface, you need a pencil, level, drill, screws, wall anchors and screwdriver for mounting. To install the Product, you need wire cutters, wire strippers and a slotted electronics screwdriver.

18. Information about repair, replacement of parts
    Do not open or disassemble product. The product can not be repaired. In case of a defect outside the warranty period, the device must be disposed of at an approved waste collection point.

19. Instructions for disposal
    Old appliances marked with the pictured symbol must not be disposed of with the
    trash. You must return them to a waste collection center (inquire at your local com-munity) or the retailer where they were purchased. They will ensure environmental-
    ly sound disposal.

20. Documentation
    The product has been manufactured and supplied in compliance with all relevant regulations and directives that apply for all member states of the European Union. The product complies with all applicable specifications and regulations in the country of purchase. Formal docu-mentation is available upon request. The formal documentation includes, but is not limited to the declaration of conformity, the material safety datasheet and the product test report.

21. CE-Declaration
    This product complies with the following directives:
    LVD: 2014/35/EU, EMC: 2014/30/EU, RoHS: 2011/65/EU, RED: 2014/53/EU

22. Explanation of symbols, concepts and particularities of the product

    • Sensor information
      Note: The high-frequency output of this sensor is <0,2mW. This is 1/5000th of the transmis-sion power of a mobile phone or the output of a microwave oven.

    •  Detection range settings (sensitivity)
      Detection range is the radius of the circular detection zone after mounting the sensor at a height of 2,5m. Turn the detection control fully anticlockwise to select minimum detection range (approx. 2m radius), and fully clockwise to select maxi-mum detection range (approx. 16m radius).
      Note: The HF sensor scanning specifications may vary slightly depending on the SENS mounting height and location.
      Attention: When using this product, please do not adjust the sensitivity to ma-ximum. Factors like blowing leaves or small animals can cause the product to turn on. If the product does not function properly, please lower the sensitivity settings.

    • Timer settings
      The light can be set to stay on for any period of time between 10 seconds (dial turned fully anti-clockwise) and a maximum of 30 minutes (dial turned fully clockwise). Any movement detected during the “on” time will reset the timer. The LED indicator will flash when adjusting the time setting dial. The number of flas-hes means the following:
      1 flash = 10 seconds, 2 flashes = 1 minute, 3 flashes = 2 minutes, 4 flashed = 5 minutes, 5 flashed = 8 minutes, 6 flashes = 10 minutes, 7 flashes = 15 minutes, 8 flashes = 20 minutes, 9 flashes = 25 minutes, 10 flashes = 30 minutes

    • Light control settings

**Problems and solutions

**

Documents / Resources

| SHADA 240120X Water Resistant Luminaire with HF-Motion Sensor [pdf] Instruction Manual
240120X, Water Resistant Luminaire with HF-Motion Sensor
---|---

References

• Home | Shada.nl

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>