SHADA 2401201-01 Water Resistant Luminaire with HF-Motion Sensor User Manual

: June 5, 2024
: SHADA

SHADA 2401201-01 Water Resistant Luminaire with HF-Motion Sensor

INSTRUCTION

SHADA 2401201-01 Water Resistant Luminaire with HF-Motion Sensor-
FIG1

TAB 1

Art. Nr.| ****

2401201_01

| ****

2401202_01

| ****

2401203_01

| ****

2401204_01

---|---|---|---|---
Total Output – Gesamtleistung – Totale Output – Puissance totale- Salida total (W)| 8| 14| 20.5| 2×14
Dimensions – Abmessungen – Afmetingen – Dimensions – dimensiones

(LxB72xH86mm)

| ****

L655

| ****

L1265

| ****

L1565

| ****

L1265

Input voltage – Eingangsspannung – voedingspanning – Tension d’entrée – voltaje

de suministro

| ****

220-240V

Frequency – Frequenz – Frequentie – Fréquence – frecuencia (Hz)| 50/60
input current – Eingangsstrom – Ingangsstroom – Courant d’entrée – corriente de

entrada

| ****

38mA

| ****

70mA

| ****

100mA

| ****

137mA

Luminous ﬂux – Lichtstrom – Lichtstroom – Flux lumineux – ﬂujo luminoso (lm)| 1125| 2100| 3000| 4200
Colour temperature – Farbtemperatur – Kleurtemperatuur – Température de couleur

– temperatua de color (K)

| ****

4.000

Dimmable – Dimmbar – Dimbaar – Dimmable – regulable| No-Nein-Neen-Non-No
Degree of protection – Schutzart – Beschermingsgraad – indice de protection –

tablero de protección

| ****

IP65

Impact strength – Schlagfestigkeit – Slagvastheid – indice de protection contre les

chocs – resistencia al impacto

| ****

IK08

Warm-up time – Aufwärmzeit – Opwarmtijd – Temps d’échauﬀement –

tiempo de calentamiento (s)

| ****

< 2

Switch cycles – Schaltzyklen – Schakelcycli – Cycles de commutation – ciclos de

conmutación

| ****

15.000x

LED: Lifespan (h) – Lebensdauer (Std.) – Levensduur (u) – Durée de vie (h) – esperanza

de vida (h)

| ****

50.000

Beam angle – Abstrahlwinkel – Stralingshoek – Angle de rayonnement – ángulo

de haz

| ****

190°

Colour rendering index (CRI) – Farbwiedergabeindex (CRI) – Index kleurweergave

(CRI) – Indice de rendu des couleurs (CRI) – valor de color de índice (CRI)

| ****

Ra >80

Sensor – Sensor – Sensor – Capteur – Sensor
Detection range – Erfassungsbereich – Detectiebereik (instelbaar) – Distance de

détection – rango de detección

| ****

2-16m | 120°

Timer – Zeitschaltuhr – Timer – Minuterie – Temporizador| 10sec – 30min
Photosensitivity – Lichtempfindlichkeit – Lichtgevoeligheid – Photosensibilite – Fotosensibilidad (Lux)| ****

10 – 2000

Frequency – Frequenz – Frequentie – Fréquence – Frecuencia (GHz)| 5.8
Standby power – Standby Leistung – Standby power – Mode veille – energía de

reserva (W)

| ****

0.5

Working temperature T – Arbeitstemperatur T – Werktemperatuur T – Température d’utilisation T – Temperatura de funcionamiento T (°C)| ****

-20≤ T ≤ ~70

Package contents

1x Water resistant luminaire with HF-sensor
1x Installation and Operating manual

Manual identiﬁcation

Shada B.V, 7328-JK Apeldoorn, Molenmakershoek 28, The Netherlands. www.shada.nl Release date: 20200424 12:03 Article number: 240120X (X=1,2,3,4)

General

This product is designed for outdoor and indoor use. It is equipped with a LED tube, a HF-motion sensor, polycarbonate housing, swivel, 2 stainless steel mount-ing brackets, 4 screws and 4 wall anchors.

Unique identiﬁcation of the product

Waterproof luminaire with HF-motion Sensor Article number: 240120X(X=1,2,3,4). The product meets the requirements of protection class 1. Level of protection IP65, dustproof, protected against water jets. Further technical data can be found in table 1. („TAB 1“ on page 3)

Modiﬁcation of the product

The product may not be changed or adapted. Do not use the product for other purposes than described in the manual.

Keep this product out of reach of children or animals. This product is not a toy, LED lights are extremely bright and looking directly at the light source during operation can lead to seri-ous eye damage. Any other use of the device than described in the manual may damage the product or cause danger to the user, e.g. due to a short circuit, ﬁre or electric shock. The safety instructions must be observed at all times.

Conformity of the product with legislation

The warranty expires in the event of damage due to non-compliance with the safety in-structions of the device. Furthermore, we are not liable for consequential damage, damage to objects or persons resulting from failure to observe the safety instructions and improper use/handling of the device due to wear and tear. Product design and speciﬁcations are sub-ject to change without notice. All logos and trade names are registered trademarks of their respective owners and are hereby acknowledged as such.

Storage of the Manual

Please read the operating instructions carefully and completely before use. The operating instructions are part of the product, they contain important information on the commission-ing and handling of the device. Keep all enclosed operating instructions for future reference. If the device is sold or passed on to third parties, you are obliged to pass on the operating instructions as these are lawfully part of the product.

Use of the product / Installation

Before use, check the completeness of the parts supplied and the intactness of the product. If damaged, it must not be put into operation. This product may only be installed by a quali-ﬁed technician.
Installation:

Decide where to mount the luminaire.
Disconnect from the mains.
Secure against being switched on again.
Verify that there is no voltage to your cable.
Follow the enclosed steps. („Fig. 1“ on page 2)

We can only ensure the correct function of the sensor when the product is mounted to the ceiling.

Operating the product

The safety instructions and warnings must be observed to ensure both the perfect condition of the product and safe operation.

Product maintenance

The product can be cleaned with clear water and a soft cloth. Do not use detergents contain-ing surface active agents or scouring agents.

Accessories, consumables, spare parts

For this product there are led tubes available separately.

Information about special tools, devices

You do not need any special tools to take this device into use. Depending on the mounting surface, you need a pencil, level, drill, screws, wall anchors and screwdriver for mounting. To install the Product, you need wire cutters, wire strippers and a slotted electronics screwdriver.

Information about repair, replacement of parts

Do not open or disassemble product. The product can not be repaired. In case of a defect outside the warranty period, the device must be disposed of at an approved waste collection point.

Instructions for disposal

Old appliances marked with the pictured symbol must not be disposed of with the trash. You must return them to a waste collection center (inquire at your local com-munity) or the retailer where they were purchased. They will ensure environmentally sound disposal.

Documentation

The product has been manufactured and supplied in compliance with all relevant regulations and directives that apply for all member states of the European Union. The product complies with all applicable speciﬁcations and regulations in the country of purchase. Formal docu-mentation is available upon request. The formal documentation includes, but is not limited to the declaration of conformity, the material safety datasheet and the product test report.

16 CE-Declaration

This product complies with the following directives: LVD: 2014/35/EU, EMC: 2014/30/EU, RoHS: 2011/65/EU, RED: 2014/53/EU

Explanation of symbols, concepts and particularities of the product

Action icon – Read this manual carefully and completely. CE is the abbreviation for Conformité Européenne – And means Conforms to the European guidelines. With the CE-mark, the manufacturer conﬁrms that this product complies with the current European guidelines.

Sensor information
Note: The high-frequency output of this sensor is <0,2mW. This is 1/5000th of the transmis-sion power of a mobile phone or the output of a microwave oven. SHADA 2401201-01 Water Resistant Luminaire with HF-Motion Sensor-
FIG2 SHADA 2401201-01 Water
Resistant Luminaire with HF-Motion Sensor-FIG3

SENS – Detection range: 2-16m (adjustable)
TIME – Timer: 10 sec – 30 min
LUX – Photosensitivity: 10-2000 Lux

Detection range settings (sensitivity)

Detection range is the radius of the circular detection zone after mounting the sensor at a height of 2,5m. Turn the detection control fully anticlockwise to select minimum detection range (approx. 2m radius), and fully clockwise to select maxi-mum detection range (approx. 16m radius). Note: The HF sensor scanning speciﬁcations may vary slightly depending on the mounting height and location. Attention: When using this product, please do not adjust the sensitivity to ma-ximum. Factors like blowing leaves or small animals can cause the product to turn on. If the product does not function properly, please lower the sensitivity settings.

Timer settings

The light can be set to stay on for any period of time between 10 seconds (dial turned fully anti-clockwise) and a maximum of 30 minutes (dial turned fully clockwise). Any movement detected during the “on” time will reset the timer. The LED indicator will ﬂash when adjusting the time setting dial. The number of ﬂas-hes means the following: 1 ﬂash = 10 seconds, 2 ﬂashes = 1 minute, 3 ﬂashes = 2 minutes, 4 ﬂashed = 5 minutes, 5 ﬂashed = 8 minutes, 6 ﬂashes = 10 minutes, 7 ﬂashes = 15 minutes, 8 ﬂashes = 20 minutes, 9 ﬂashes = 25 minutes, 10 ﬂashes = 30 minutes

Light control settings

The chosen light response threshold can be anywhere between 10-2000 lux. Turn the dial anti-clockwise to select dusk to dawn operation at 10 lux. Turn the dial fully clockwise to select daylight operation at 2000 lux. The dial must be turned fully clockwise when adjusting and testing the detection zone. Note: please do not adjust the three dials past their maximum, as this will dama-ge the product.

Problems and solutions

The light does not switch on

| Wrong light-control setting selected| Check and adjust settings
---|---|---
Broken light| Change light
Main switch is OFF| Switch ON
The light is on all the time| Continuous movement in the detection zone| Check zone setting
The light will go on without any visible movement| The sensor is not mounted for detecting movement reliably| ****

Securely mount the sensor