TFA 35.8000.01 View Meteo WLAN Radio Weather Station Instruction Manual

TFA 35.8000.01 View Meteo WLAN Radio Weather Station

VIEW METEO
WIFI Wireless Weather Station
Cat. No. 35.8000.01
Thank you for choosing this product from TFA.
Before you use this product
Please make sure you read the instruction manual carefully. Following and respecting the instructions in your manual will prevent damage to your instrument and loss of your statutory rights arising from defects due to incorrect use. We shall not be liable for any damage occurring as a result of non-following of these instructions. Likewise, we take no responsibility for any incorrect readings or for any consequences resulting from them.
Please pay particular attention to the safety notices! Please keep this instruction manual safe for future reference.

Delivery contents

• Base station

• Power adaptor for base station

• Temperature-humidity transmitter (30.3800.02)

• Instruction manual
  For your safety

• This product is exclusively intended for the range of application described in point 3.

• It should only be used as described within these instructions.

• Unauthorized repairs, alterations or changes to the devices are prohibited.
  Caution!
  Risk of electrocution!

• Plug the base station only into a mains socket installed within your country’s electrical safety regulations and with a correct mains voltage (see nameplate).

• The mains socket must be located near the equipment and it must be easily accessible.

• Unplug the device immediately if any fault occurs.

• The base station and the power adapter must not come into contact with water or moisture. Suitable for indoor use only.

• Do not use the device if the housing or the power adapter are damaged.

• Operate the device out of reach of persons (including children) who cannot fully appreciate the potential risks of handling electrical equipment.

• Only use the supplied power adapter.

• Route the mains cable so it does not come into contact with sharp-edged or hot objects.

Important information on product safety !

• Do not expose the device to extreme temperatures, vibrations or shocks.
• The outdoor transmitter is splashproof, but not watertight. When placed outdoors, choose a dry place for the transmitter.

Caution!Risk of injury:

• Keep the devices and the batteries out of reach of children.
• Small parts can be swallowed by children (under three years old).
• Batteries contain harmful acids and may be hazardous if swallowed. If a battery is swallowed, this can lead to serious internal burns and death within two hours. If you suspect a battery could have been swallowed or otherwise caught in the body, seek medical help immediately.
• Batteries must not be thrown into a fire, short-circuited, taken apart or recharged. Risk of explosion!
• Low batteries should be changed as soon as possible to prevent damage caused by leaking. Make sure the polarities are correct. Never use a combination of old and new batteries together, nor batteries of different types.
• Remove the batteries if the device will not be used for an extended period of time.
• Avoid contact with skin, eyes and mucous membranes when handling leaking batteries. In case of contact, immediately rinse the affected areas with water and consult a doctor.

Range of application and all the benefits of your new instrument at a glance:

• Wireless weather station with local, self-measured values (can also be used without Wi-Fi), with online connection in combination with numerous online weather data for the region and an extended use of local measured values via free VIEW app (iOS and Android)
• Permanently illuminated colour display with 4 brightness levels and adjustable dimming function
• Time and date, with online connection: automatic setting and updating
• Weekday written in full letters and menu in 4 languages (German, English, French and Spanish) Indoor temperature and humidity
• Wireless transmission of outdoor temperature and humidity via transmitter (868 MHz, max. 100m)
• Heat index and dew point display can be accessed
• Weather forecast with symbols for the next 12 hours (based on the change in atmospheric pressure values), the coloured weather image changes with the seasons, with online connection as professional forecast with probability of rain
• Permanent display of daily maximum and minimum temperatures of the outdoor transmitter, with online connection as professional fore- cast for the region
• Max-min function for all temperature and humidity values can be accessed.
• Alarm function for temperature and humidity values, with online connection: Alarm can be set via push notification to your mobile device
• Additional functions with online connection via VIEW app: Retrieval of measured values from the station (including history of the last 30 days), further transmitters can be added (optionally available)
• Additional functions on the station with online connection: Additional weather information and personalised messages in the text display
• Power supply (included), absolutely necessary for permanent display illumination and Wi-Fi function
• 3x AA 1.5V for battery operation or as backup batteries (not included)

Below you will find a comparison of which functions are available without and with an online connection:

Elements

Base station
Display (Fig.1 )
A – FORECAST section weather symbols and probability of rainfall B – OUTDOOR section with outdoor temperature and humidity C – INDOOR section with indoor temperature and humidity
D – Time/date and info section
E – FORECAST and OUTDOOR-RECORDS

Buttons (Fig.2)
A – ALERTS button B – TEMP button C – SENSOR button D – + button
E – – button
F – SET button
G – LIGHT button

Housing (Fig.3)
A – Wall mounting holes B – Stand (fold-out)
C – Battery compartment D – Power adaptor jack

Transmitter (Fig.4)
Display
A1 – Unit (°C, °F or %)
A2 – Display of temperature and humidity
A3 – Battery symbol

Housing & buttons
B – Wall mounting holes C – °F/°C button
D – Battery compartment E – TX button

Getting started

• Place the base station and the transmitter on a table at a distance of about 1.5 meters from each other.

• Remove the protective film from the base station display
  5.1 Starting the devices

• Temperature-humidity transmitter: Open the battery compartment (Fig.4-D) of the temperature-humidity transmitter and insert two new AA 1.5 V batteries. Make sure the polarities are correct. Close the battery cover again.

• Base station: Connect the supplied power adapter to the mains and then to the base station (Fig.3-D). The device will alert you with a beep and all segments will be displayed for a short moment.

• After a few seconds, the station greets you with HALLO (hello) and displays the first item of the settings menu.

• If you want to use the station generally/for the time being without an online connection, you can now make all settings and adjustments manually (see comprehensive description at point 6.1, the following point 5.2 can then be skipped).

• If you prefer to connect the station to the Internet straightaway, most of the settings will be made automatically. In this case, we recommend ignoring the settings menu for now (the device automatically exits the setting menu if no button is pressed for 10 seconds).

• The measured values of the transmitter are received by the base station and shown in the display within the first 10 minutes.

Connect the station to the Internet

• Download the free TFA VIEW App from the “Apple App Store” or “Google Play Store”.
• After you have created an account and started the app, select „Devices“ in the menu. There you can add, remove or sort devices on the App. You can add devices with the „Add device“ button in the iOS app or the blue „+“ button in the Android app.
• Now follow the instructions and steps exactly as given by the app.

Legal information:
Google Play and the Google Play logo are trademarks of Google LLC. App Store and the Apple logo are trademarks of Apple Inc.

CAUTION:

• During the connection process, you will be instructed to switch to the smartphone/tablet settings and briefly connect directly to the station in order to transfer the previously collected network data. Please do not close the app when doing this! Only put the app in the background and put it back in the foreground after the Wi-Fi connection with the station.
• The station only operates via 2,4GHz. Operation with a Wi-Fi network in dual-band mode (2.4 GHz & 5 GHz simultaneously) is also possible. However, if there are any problems during the connection process, it is recommended to adjust the settings of the Wi-Fi network and temporarily use only 2.4GHz during the integration process.
• After successfully finishing all the steps regarding the online connection in the app, it will only take a few minutes until the correct time and date are set fully automatically on your VIEW station and professional weather data is received.
• The readings from your VIEW station will be displayed in the app after a few minutes. Transmitters that were already connected to the VIEW station before the Wi-Fi connection will be suggested as additional devices in the notification area of the app after a few minutes, in order to add them in the app as well.
• If a transmitter is added subsequently (or was not automatically detected in the course of the connection process), select “Devices” in device management on the app menu. Here you can also scan and add individual transmitters. These are received by the VIEW station and forwarded to the server/app.
• Further information about the Wi-Fi connection can be found in the user manual under point 6.6.

Back-up battery

• The 3x AA 1,5V batteries will operate as a backup power source in case of power failure or change of location. In pure battery operation, a short-term display of the local measured values and activation of the display illumination (10 sec.) is possible by pressing any key.
• For permanent display illumination and Wi-Fi function, use the supplied power adapter.
• Open the battery compartment, insert 3 new batteries AA 1.5 V, polarity as illustrated and close the battery compartment again.

Operation

Manual setting mode
Immediately after set-up or if you press and hold the SET button (Fig.2-F) for three seconds, you enter the setting mode.

• HALLO is displayed shortly and DEUTSCH (German, language default setting for day-of-the-week display and menu) flashes.
• The setting can be changed with the “+” and “-” keys (Fig.2-D+E), if you wish. Confirm the setting with the SET button.
• The next adjustable value flashes on the display.
• Use the “+” or “-” button to make the desired setting.
• Press and hold the “+” or “-” button in setting mode for fast mode.
• The device will automatically quit the setting mode if no button is pressed for 10 seconds.
• Confirm with the SET button and go to the next setting. y The sequence is shown as follows:
  • Language setting (default: DEUTSCH)
  • Button tone (default: BEEP OFF)
  • 12/24-hour format (default: 24Hr)
  • Hours, minutes
  • Year, month, date
  • Date format (default: DATE/MONTH)
  • °C/°F (default: °C)
• “THANK YOU” is then briefly displayed as the last menu item.

Language for day-of-the-week display and menu

• The default setting is “German” (DEUTSCH).
• Use the “+” or “-” button (Fig.2-D+E) to change the weekday display and menu to English, Spanish or French.
• Confirm the setting with the SET button (Fig.2-F).

Button tone

• The default setting is BEEP “OFF”.
• If you would like a confirmation beep every time you press a button on the station, use the “+” or “-” button to select “ON”.
• Confirm the setting with the SET button.

Time

• The default time format setting is “24Hr”.
• If you would like the 12-hour-format (AM/PM), use the “+” or “-” button to select “12Hr”.
• Confirm the setting with the SET button.
• Press the “+” or “-” button to set the hours and the minutes, and confirm each setting with the SET button.

Date

• Use the “+” or “-” button to set the year, month and date and confirm each setting with the “SET” button.
• The default date format setting is “DATE/MONTH”.
• If you would like the “MONTH/DATE” format, use the “+” or “-” button to select “MONTH/DATE”.
• Confirm the setting with the SET button.

Temperature unit

• The default setting is “°C”.
• If you would like “°F” as temperature unit, use the “+” or “-” button to select “°F”.
• Confirm the setting with the SET button.

Display illumination

• The brightness can be adjusted to 5 different levels.
• With a simple press of the LIGHT button (Fig.2-G), you can choose between BACKLIGHT “OFF” (display illumination deactivated), and the levels “1” (minimum brightness), “2”, “3” and “4 (maximum brightness, default setting). The last selected level will remain permanently active.

AutoDim function

• If you wish, an automatic dimming function can be activated during night time.

• The display illumination is then automatically switched to level 1 (minimum brightness) for the specified time slot.

• Press and hold the LIGHT button for 3 seconds. AUTO DIM appears on the display and OFF (default) flashes. Press the “+” or “-” button
  (Fig-2-D+E) to select ON.

• Confirm the setting with the LIGHT button.

• The start time flashes (23:00 default). Use the “+” or “-” button to adjust the start time.

• Confirm the setting with the LIGHT button.

• The stop time flashes (6:00 default). Use the “+” or “-” button to adjust the stop time.

• Confirm the setting with the LIGHT button.

If the AutoDim function has been activated, in the time area (Fig.1-D) (above the seconds) „AutoDim“ is permanently shown in the display.

Description of the display areas
Some of the display areas of the VIEW METEO radio-controlled weather station cat.no. 35.8000.01 have the option of several different functions. When there is an online connection, the standard function (without online connection) is either changed/extended or completely replaced by another function.

Display area: weekday, time, date (Fig.1-D)
Standard function (without online connection)

• In the normal display, the day of the week, the current time and the date are shown here.
• In the settings menu and with different history functions, information on the respective setting option or the selected measured value is displayed in this area.
• Information and status requests (see point 6.6 to point 6.9) are also displayed briefly in this area

With online connection/display area for stream info function

• After a successful connection via the local network, a radio symbol “WIFI” is permanently displayed in the time area (above the seconds).
• If you use the “Stream Info” function via the app, the selected additional weather information or personalised messages (up to 3 pieces of information can be actively selected) are displayed in this area, alternating with the normal display every 5 seconds.

The day of the week, current time and date are only permanently displayed if no additional information/message is set for the device via the app in “Stream Info”.

Display area: Indoor temperature and humidity (Fig.1-C)

Standard function (without online connection)

• Display of indoor temperature and humidity

With online connection

• No additional function or change

Display area: outdoor temperature and humidity (Fig.1-B)

Standard function (without online connection)

• Display of outdoor temperature and humidity received from the temperature-humidity transmitter.

• The trend arrows indicate whether the outdoor values for temperature and humidity of the last 60 minutes are increasing or decreasing. If the values remain the same, there is no display. The display is updated every 15 minutes.

• Measured values have increased by >1°C or >3% points rH

• Measured values have decreased by >1°C or >3% points rH

• This station does not have the option of displaying additional transmitters directly on the base station. Additional compatible transmitters can be received in the background and forwarded to the server when the online connection is active.
  IMPORTANT: These additional transmitters can only be used via the app.

• If several temperature-humidity transmitters are connected, press the “SENSOR” button (Fig.2-C) to identify the transmitter in this display area (see point 6.8). You can also remove the transmitter from this display area or start a manual search.

With online connection

• No additional function or change

Display area: maximum and minimum temperature (Fig.1-E)
Standard function (without online connection) / OUTDOOR RECORDS

• On the normal display, the highest measured temperature (HI) and the lowest measured temperature (LO) of the temperature-humidity transmitter for the current day are shown here. The HI/LO values are continuously updated and automatically reset at midnight.

With online connection / FORECAST

• When forecast values are received for this display area while the online connection is active, a small radio symbol is permanently displayed next to FORECAST (on the left).
• The temperature values displayed are the expected highest temperature (HI) and the expected lowest temperature (LO) for the current day.
• The forecast refers to the location (region/zip code) that was saved during the installation of the device via the app.

Display area: weather symbol „FORECAST“ (Fig.1-A)
Standard function (without online connection) / FORECAST

• On the normal display, a symbol for the coming weather based on the changes in atmospheric pressure measured by the base station is shown here.
• There are 6 different weather symbols:

The weather forecast covers a range of 12 hours and indicates only a general weather trend. For example, if the current weather is cloudy and the rain symbol is displayed, it does not mean the product is faulty because it is not raining. It simply means that the atmospheric pressure has dropped and the weather is expected to get worse but not necessarily rain.

• The landscape image changes with the seasons. (1. Spring | 2. Summer | 3. Autumn | 4. Winter)

• The sun symbol is also displayed at night if the atmospheric pressure develops positively.

With online connection / FORECAST

• When forecast values are received for this display area while the online connection is active, a small radio symbol is permanently displayed next to FORECAST (on the right).
• The weather symbol displayed is then a forecast for the next 12 hours prepared by professional meteorologists.
• There are 12 different weather symbols:

• In the upper left corner, the probability of rain in percent is displayed next to the weather symbol.
• The forecast refers to the location (region/zip code) that was saved during the installation of the device via the app.

Max-min function, heat index and dew point

Max-min function for temperature & humidity + heat index & dew point of the outdoor transmitter

• Press the TEMP button (Fig.2-B) in normal mode.
• You can now see the HI RECORD for the outdoor temperature (since the start-up or the last reset) with time and date of recording.
• Press the TEMP button and go to the next information.
• The sequence of the available information in this mode is shown as follows:
• HI RECORD Outdoor temperature
• LO RECORD Outdoor temperature
• HI RECORD Outdoor humidity
• LO RECORD Outdoor humidity
• HI RECORD Indoor temperature
• LO RECORD Indoor temperature
• HI RECORD Indoor humidity
• LO RECORD Indoor humidity
• Current heat index temperature of the outdoor transmitter
• Current dew point temperature of the outdoor transmitter
• Hold the “-” button (Fig.2-E) for 5 seconds while the respective value is displayed to clear the recorded readings. Every max-min value can be reset individually.
• The device will automatically quit the max-min mode if no button is pressed for 10 seconds.
• The heat index temperature is calculated above +26.6°C using the outdoor temperature and outdoor humidity. Below, this value is identical to the outdoor temperature.

Alert settings

• Press and hold the ALERTS button (Fig.2-A) for three seconds to enter the alert setting mode.
• OFF flashes and the first setting option HI ALERT (upper limit) of the outdoor temperature is displayed. If you do not want to set this alert, press the ALERTS button again to move to LO ALERT (lower limit) of the outdoor temperature.
• To activate (ON) or deactivate (OFF) the alert setting function, press the “+” or “-” button (Fig.2-D+E).
• Press the ALERTS button to confirm the settings. The corresponding value flashes. Press “+” or “-” button to adjus the respective alert value.
• Confirm with the ALERTS button and go to the next setting.
• The sequence of the available alert settings in this mode is shown as follows:
  • HI and LO ALERT Outdoor temperature
  • HI and LO ALERT Outdoor humidity
  • HI and LO ALERT Indoor temperature
  • HI and LO ALERT Indoor humidity

Alarm event:

• In the event of an alarm, the corresponding symbol will be flashing and an alarm tone will sound 5 times per minute.
• Stop the alarm sound with any button.
• The alert symbol continues to flash until the measured value is within the alarm limits.

Wi-Fi Connection

• Press the SET button (Fig.2-F) once briefly in normal mode to display the Wi-Fi status for 3 seconds.

• SEE APP TO CONNECT – the station is trying to connect with the already registered Wi-Fi network or is in Wi-Fi configuration mode.

• LOST WIFI – the station has not yet been connected to the local Wi-Fi network or currently has no contact with the Wi-Fi network already registered.

• ALL OK CONNECTED – the station is actively connected to the Wi-Fi network.

• The Wi-Fi symbol next to the time is permanently displayed when the station is actively connected to the Wi-Fi network.

• The Wi-Fi symbol next to the time flashes when the station is in the process of connecting to the already registered network or in Wi-Fi configuration mode.

• If no information for the local Wi-Fi network has been transferred yet or if it has to be transferred again (because the network name or password has changed, for example), initiate a new configuration via the app.

• If the station has not yet been connected to the local Wi-Fi network or to the app/account, please add the station via the device management (described in detail in point 5.2).

• If the station has already been registered in the app or the account and only the Wi-Fi configuration needs to be performed again, please select the option “Connect Wi-Fi” in the menu of the app.

• During Wi-Fi configuration, the app will ask you to activate Wi-Fi configuration mode on the station by pressing and holding the SET (Fig.2-F) and “+” (Fig.2-D) buttons simultaneously (for 5 seconds).

• After a restart, the station automatically tries to connect to the known network (Wi-Fi symbol flashes). If no connection could be establishedafter 15 minutes, the Wi-Fi symbol disappears.
  Battery displays

• As soon as the battery symbol appears on the display of the outdoor transmitter (Fig.1-B), change the batteries of the corresponding transmitter.

• As soon as the battery symbol appears in the display of the indoor values (Fig.1-C), either no backup batteries are inserted or they should be changed.

Checking device ID and additional transmitters
SENSOR button (Fig.2-C)

• If you briefly press the SENSOR button once in normal mode, the station displays the device ID of the base station and the measured values (indoor temperature and indoor humidity) that are transmitted from this device to the server/app.
• If you briefly press the SENSOR button again, the station displays the device ID of the temperature-humidity transmitter and the measured values (outdoor temperature and outdoor humidity) that are transmitted from this device to the server/app.
• If you briefly press the SENSOR button again, you will return to normal mode.
• If you want to remove the currently received temperature-humidity transmitter, select the transmitter and press and hold the “-” button M(Fig.2-E) for 5 seconds.
• The device will automatically quit the mode if no button is pressed for 5 seconds.

Manual search for the transmitter

• Press and hold the SENSOR button (Fig.2-C) in normal mode for 3 seconds to start the transmitter search. The radio symbol is shown flashing in this area.
• For a successful transmitter search, it is recommended to place the desired transmitter next to the base station during the search and to insert the batteries in the corresponding transmitter immediately after initiating the manual search, or also to briefly press the TX button (Fig.4-E) of the corresponding transmitter.
• After a transmitter has been successfully received, a short beep is emitted, its measured values and the corresponding radio symbol are permanently displayed.

Factory-reset & firmware information
Factory-reset

• In case of a serious malfunction or if you want to reset all settings and memories of the station to factory settings, press and hold the buttons ALERTS (Fig.2-A) and LIGHT (Fig.2-G) simultaneously for 3 seconds.

Check the firmware version

• To check the firmware version, press and hold the SENSOR (Fig.2-C) and TEMP (Fig.2-B) buttons simultaneously for 3 seconds. A version info of the station firmware is displayed and then a version info of the firmware of the Wi-Fi module appears briefly.

Positioning

Positioning and mounting of the base station and the transmitter

• With the foldable stand (Fig.3-B) at the back, the base station can be placed onto any flat surface.

• The base station can be mounted at a chosen location with the mounting holes (Fig.3-A) found at the back of the device.

• Make sure to avoid the vicinity of any source of interference such as computer screens, TV sets or solid metal objects.

• Do not use the base station in the vicinity of radiators, other sources of heat or in direct sunlight.

• The outdoor transmitter (Fig.4) can be placed onto any flat surface or wall mounted at a chosen location with the mounting hole (Fig.4-B) found at the back of the device. When placed outdoors, choose a shady and dry place for the transmitter. Direct sunlight may trigger incorrect measurement and continuous humidity damages the electronic components needlessly.

• Once the desired location is chosen, check whether the transmission from the transmitter to the base station is possible (transmission range of up to 100 m in open areas). Within solid walls, especially ones with metal parts, the transmission range can be reduced considerably.

• If necessary, choose another position for the outdoor transmitter and/or base station.

• Make sure that the base station has sufficient reception of the Wi-Fi signal at the installation location.
  Care and maintenance

• Clean the devices with a soft damp cloth. Do not use solvents or scouring agents.

• Remove the batteries and unplug the power adapter of the base station if the device will not be used for a long period of time.

• Store the devices in a dry place.

Troubleshooting

Connect the base station to the power adapter Activate backlight

Check the power adapter

Battery operation:

Ensure the batteries’ polarities are correct

Press any button to activate the backlight briefly Change the batteries

No reception of the outdoor transmitter Display “- -”| No outdoor transmitter is installed

Check the outdoor transmitter’s batteries (only use batteries/rechargeable batteries with 1.5V voltage!) Restart the outdoor transmitter and the base station according to the manual

Manual search for the transmitter (according to the manual) Choose another place for the transmitter and/or the base station Reduce the distance between the transmitter and the base station Check if there is any source of interference.

Incorrect indication| Factory reset: see point 6.9.1 Battery operation

Change the batteries

Display Hi/Lo at measured values| Outside measuring range

For more information on troubleshooting, see the FAQs on our website:
www.tfa-dostmann.de/en/service/frequently-asked-questions/faq-view- stations/
If your device fails to work despite these measures, contact the retailer where you purchased the product.

Specifications

Base station

• Measuring range – temperature: 0°C … +50°C (+32°F … +122°F)

• Measuring range – humidity: 10% … 99% rH

• Precision: temperature (± 1°), humidity (± 5%)

• Power supply:  Power adaptor (inclusive), batteries (3 x AA 1.5V, not included)
  We recommend Alkaline batteries.

• Input power adaptor: 100-240 V~, 50/60 Hz, 0.5A Max

• Output power adaptor: 5 V⎓, 0.6A, 3W

• Average active efficiency: ≥ 69.64%

• No-load power consumption: ≤ 0,1 W

• Transmission frequency: 868 MHz

• Maximum radio-frequency power: < 25mW

• Transmission range: 100m (open field)

• Dimensions: 197 x 32 (85) x 163 mm

• Weight: 343 g (device only)

Wi-Fi requirements
Wi-Fi transmission frequency: 2.4 GHz (802.11 b/g/n)
Network name/network password: must not exceed 45 characters
Network speed: Minimum 1 Mbit/s

Important! If you have a multi-band router (e.g. 2.4 & 5 GHz), make sure your mobile device is connected to the 2.4 GHz network if you want to connect base station and app.

Requirements for your mobile device (smartphone or tablet)
Apple devices require at least iOS 9 or higher and Internet access via Wi-Fi or mobile data.
Android devices require at least OS 5.0 or higher and Internet access via Wi- Fi or mobile data.

Temperature-humidity sensor
Measuring range – temperature: -40°C … +60°C (-40°F … +140°F)
Measuring range – humidity: 10% … 99% rH
Power supply: 2 x AA 1.5V (not included). We recommend Alkaline batteries.
Battery life: ca. 2 years (with Alkaline batteries)
Dimensions: 50 x 20 x 145 mm
Weight: 60 g (device only)

Google Play and the Google Play logo are trademarks of Google LLC. Android is a trademark of Google LLC.
Apple, Apple Watch, iPad, iPod, iPod touch, and iPhone, are trademarks of Apple Inc., registered in the U.S. and other countries. App Store is a service mark of Apple Inc.,
registered in the U.S. and other countries. IOS is a trademark or registered trademark of Cisco in the U.S. and other countries and is used under license.

Waste disposal
This product and its packaging have been manufactured using high-grade materials and components which can be recycled and reused. This reduces waste and protects the environment.
Dispose of the packaging in an environmentally friendly manner using the collection systems that have been set up.

Disposal of the electrical device
Remove non-permanently installed batteries and rechargeable batteries from the device and dispose of them separately.
This product is labelled in accordance with the EU Waste Electrical and Electronic Equipment Directive (WEEE).
This product must not be disposed of in ordinary household waste. As a consumer, you are required to take end-of-life devices to a designated collection point for the disposal of electrical and electronic equipment, in order to ensure environmentally-compatible disposal. Observe the current regulations in place!

Disposal of the batteries
Never dispose of empty batteries and rechargeable batteries with ordinary household waste. They contain pollutants which, if improperly disposed of, can harm the environment and human health. As a consumer, you are required by law to take them to your retail store or to an appropriate collection site depending on national or local regulations in order to protect the environment. The symbols for the contained heavy metals are: Cd = cadmium, Hg = mercury, Pb = lead.

EU declaration of conformity
Hereby, TFA Dostmann declares that the radio equipment type 35.8000.01 is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: www.tfa- dostmann.de/service/downloads/ce
TFA Dostmann GmbH & Co.KG, Zum Ottersberg 12, 97877 Wertheim, Germany
Handelsregister-Nummer: Reg. Gericht Mannheim HRA 570186
No part of this manual may be reproduced without written consent of TFA Dostmann. The technical data are correct at the time of going to print and may change without prior notice.

References

• cat.no
• FAQ VIEW-Stations – TFA Dostmann
• EU-Konformitätserklärung | TFA Dostmann
• FAQ: VIEW-Stationen | TFA Dostmann

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>