KIMO 1005A 12V Max Cordless Adjustable Clutch Drill Instruction Manual
- June 5, 2024
- KIMO
Table of Contents
1005A
WIN INSTRUCTION MANUAL
12V Max Cordless Adjustable Clutch Drill
www.kimotool.com 
If you have questions or comments, contact us at service@kimotools.com
SAVE THIS INSTRUCTIONAL MANUAL
FOR FUTURE REFERENCE.
WARNING! Read and understand all instructions. Failure to follow all instructions listed below may result in electric shock, fire and/or serious personal injury.
GENERAL SAFETY RULES
WORK AREA
- Keep your work area clean and well-lit. Cluttered benches and dark areas invite accidents.
- Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power tools create sparks that may ignite dust or fumes.
- Keep bystanders, children, and visitors away while operating a power tool. Distractions can cause you to lose control.
ELECTRICAL SAFETY
- Don’t expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.
PERSONAL SAFETY
- Stay alert, watch what you are doing, and use common sense when operating a power tool. Do not use tools while tired or under the influence of drugs, alcohol, or medication. A moment of inattention while operating power tools may result in serious personal injury.
- Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your hair, clothing, and gloves away from moving parts. Loose clothing, jewelry, or long hair can be caught in moving parts. Air vents often cover moving parts and should also be avoided.
- Avoid accidental starting. Be sure the switch is off before plugging in. Carrying tools with your finger on the switch or plugging in tools that have the switch on invites accidents.
- Remove adjusting keys or wrenches before turning the tool on. A wrench or a key that is left attached to a rotating part of the tool may result in personal injury.
- Do not overreach. Keep proper footing and balance at all times. Proper footing and balance enable better control of the tool in unexpected situations.
- Use safety equipment. Always wear eye protection. Dust mask, non-skid safety shoes, hard hat, or hearing protection must be used for appropriate conditions.
TOOL USE AND CARE
- Use clamps or another practical way to secure and support the workpiece to a stable platform. Holding the work by hand or against your body is unstable and may lead to loss of control.
- Do not force tool. Use the correct tool for your application. The correct tool will do the job better at the rate at which it is designed.
- Do not use the tool if the switch does not turn on or off. Any tool that cannot be controlled with the switch is dangerous and must be repaired.
- Store idle tools out of reach of children and other untrained persons. Tools are dangerous in the hands of untrained users.
- Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained tools, with sharp cutting edges, are less likely to bind and are easier to control.
- Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the tool’s operation. If damaged, have the tool serviced before using. Many accidents are caused by poorly maintained tools.
- Use only accessories that are recommended by the manufacturer for your model. Accessories that may be suitable for one tool, may become hazardous when used on another tool.
COMPONENTS AND SPECIFICATIONS
- Variable Speed Switch
- Forward/Reverse Button (Lock-Off Button)
- Torque Adjustment Collar
- Keyless Chuck
- Battery
- Battery Release Button
- Charger
- Magnetic Bit Holder
| Model | 1005A |
|---|---|
| Voltage | 12V |
| Battery Specification | 2.0 Ah |
| Charging Time | 1-1.5 Hour |
| Chuck Size | 3/8″ |
| Max Torque | 280 In-Lb. |
| Low Speed | 350 Revolution/Minute (RPM) |
| High Speed | 1350 Revolution/Minute (RPM) |
| Weight (Bare Tool) | 1.86Lbs. |
| Weight (Tool + Battery) | 2.21 Lbs. |
SPECIFIC INSTRUCTIONS
WARNING! Hold power tool by insulated gripping surfaces, when performing an operation where the fastener may contact hidden wiring. Fasteners contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock.
Installing and Removing the Battery Pack from the Tool
To install a battery pack: Insert the battery pack into the tool, until an
audible click is heard. (figure A)
To remove the battery pack: Depress the battery release button as shown in
figure B and pull the battery pack out of the tool.
FUEL GAUGE
KIMO cordless drill includes a fuel gauge which consists of three LED lights
that indicate the level of charge remaining in the battery pack. The fuel
gauge is an indication of approximate levels of charge remaining in the
battery pack according to the following indicators:
| Remaining Capacity | Indicator Lights |
|---|---|
| 20% | |
| 20%- 40% | |
| 40%-70% | |
| 70%-100% |
Using the Forward/Reverse Control Button
A forward/reverse button determines the direction of the tool and also serves
as a lock-off button.
To select forward rotation, release the trigger switch (1) and depress the
forward/reverse control button (2). To select reverse, depress the
forward/reverse control button (2) on the opposite.
NOTE: The center position of the control button (2) locks the tool in the
off position. When changing the position of the control button, be sure that
trigger (1) is released.
Starting, Stopping, and Controlling Speed
-
To turn ON and OFF the tool, pull and release the trigger switch (1).
NOTE: An LED is turned on when the switch is pulled. -
To vary the driving speed, increase or decrease pressure on the switch. The farther the trigger is depressed, the higher the speed of the drill.
-
To stop the tool, release the switch.
-
To lock the tool, depress the forward/reverse control button (2) to the center position until an audible click is heard.
WARNING! Always lock the trigger switch or remove the battery pack before performing maintenance, changing accessories, storing the tool, and any time the tool is not in use.
Controlling Torque
This tool is equipped with a torque adjustment collar (3) to select the
operating mode and to set the torque for tightening screws. Large screws and
hard workpiece materials require a higher torque setting than small screws and
soft workpiece materials.’
Attaching and Removing Accessories
To insert a drill bit or other accessory:
- Grasp the rear half of the chuck (4) with one hand and use your other hand to rotate the front half (4a) in the counterclockwise direction, as viewed at the chuck end.
- Insert the bit or other accessory fully into the chuck, and tighten securely by holding the rear half of the chuck and rotating the front portion clockwise as viewed from the chuck end.
NOTE: Built-in magnetic bit holders (8) are located on both sides of the drill.
WARNING! Do not attempt to tighten drill bits (or any other accessory) by gripping the front part of the chuck and turning the tool on. Damage to the chuck and personal injury may occur when changing accessories.
Charging Procedure
KIMO chargers are designed to charge KIMO battery packs in 60 to 90 minutes depending on the pack being charged.
To charge the battery:
- Insert the charger cable into the charging hole at the battery. (shown in figure C)
- Plug the charger into an appropriate outlet after inserting the battery pack. Recharge discharged batteries as soon as possible after use or battery life may be greatly diminished. for the longest battery life, do not discharge batteries fully. It is recommended that the batteries be recharged after each use.
Charger Indicator
| Red Indicator | Green Indicator | Battery Pack | Status |
|---|---|---|---|
| ON | OFF | Charging | Charging |
| OFF | ON | Charged | Charged |
| OFF | OFF | Short Circuited | Short Circuited |
IMPORTANT SAFETY INSTRUCTIONS FOR BATTERY CARTRIDGE
- Before using the battery cartridge read all instructions and cautionary markings on (1) battery charger, (2) battery, and (3) product using the battery.
- Do not disassemble the battery cartridge.
- If the operating time has become excessively shorter, stop operating immediately. It may result in a risk of overheating, possible burns, and even an explosion.
- If electrolyte gets into your eyes, rinse them out with clear water and seek medical attention right away. It may result in loss of your eyesight.
- Do not short the battery cartridge: (1) Do not touch the terminals with any conductive material. (2) Avoid storing the battery cartridge in a container with other metal objects such as nails, coins, etc. (3) Do not expose the battery cartridge to water or rain. A battery short can cause a large current flow, overheating, possible burns, and even a breakdown.
- Do not store the tool and battery cartridge in locations where the temperature may reach or exceed 122° F.
- Do not incinerate the battery cartridge even if it is severely damaged or is completely worn out. The battery cartridge can explode in a fire. 8. Be careful not to drop or strike the battery.
- Do not use a damaged battery.
- how do your local regulations relate to the disposal of batteries?
TROUBLESHOOTING
| Problems | Probable Causes | Solutions |
|---|---|---|
| The unit will not operate. | The battery pack was not installed correctly. |
Check battery pack installation.
The battery pack is not charged.| Check battery pack charging requirements.
The battery pack will not charge.| The charging cable is not inserted into the
battery properly.| Insert the charging cable into the battery and check the
red LED appears.
The charger is not plugged in.| Plug charger into a working outlet
Surrounding air temperature too hot or too cold.| Move the charger and battery
pack to a surrounding air temperature of above 40°F or below 105°F
The unit shuts off abruptly.| The battery pack had reached its maximum thermal
limit.| Allow the battery pack to cool down.
Out of charge.| Place on the charger and allow to charge.
MAINTENACE
WARNING! To reduce the risk of serious personal injury, place the forward/reverse button in the lock-off position or turn the tool off and disconnect the battery pack before making any adjustments or removing/installing attachments or accessories. An accidental start-up can cause injury
Cleaning
- Keep all safety devices, air vents, and the motor housing free of dirt and dust as far as possible. Wipe the equipment with a clean cloth or blow it with compressed air at low pressure.
- We recommend that you clean the device immediately each time you have finished using it.
- Clean the equipment regularly with a moist cloth and some soft soap. Do not use cleaning agents or solvents; these could attack the plastic parts of the equipment. Ensure that no water can seep into the device.
- To assure product SAFETY and RELIABILITY, repairs, maintenance, and adjustment (including brush inspection and replacement) should be performed by a KIMO factory service center.
Every KIMO power tool is warranted to the original purchaser only
WARRANTY
To be free from defects in material and workmanship. Subject to certain exceptions, KIMO will replace any part on an electric power tool that is defective in material or workmanship for a period of 2 years after the date of purchase unless otherwise noted. This warranty does not apply to damage from repairs made or attempted by anyone other than KIMO, misuse, alterations, abuse, normal wear and tear, lack of maintenance, or accidents. Normal Wear: Many power tools need periodic parts replacement and service to achieve the best performance. This warranty does not cover repair when normal use has exhausted the life of a part including, but not limited to, chucks, brushes, cords, saw shoes, blade clamps, o-rings, seals, and driver blades. Warranty Registration is not necessary to obtain the applicable warranty on a KIMO power tool product. This warranty applies to products sold in the U.S.A. only.
EXTENDED WARRANTY REGISTRATION
Dear Customer,
Thank you very much for choosing KIMO. At KIMO, customer satisfaction is our
highest priority. In order to provide the best services, we would like to
offer you an extra 6-month limited warranty. Below is the free registration
process.
To register our extended warranty for your KIMO product, please send your
name, your email, AND your Amazon order number to
Service@kimotools.com Our customer services
representative will help you register within 24 hours.
Disclaimer: This policy is at the manufacturer’s discretion.
Best Regards, KIMO Customer Support
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>