EATON TechBench Desk and Workbench System Installation Guide

: June 5, 2024
: EATON

Table of Contents

TechBench Overview
LINEAR BENCH ASSEMBLY (36″ [914,4mm] wide to 96″ [2438,4mm] wide
LINEAR BENCH ASSEMBLY (24″ wide and 30″ wide)
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)
1 and #2 Magnetic tip phillips head bit (not supplied)

TechBench Desk and Workbench System
Installation Guide

TechBench Overview

TechBenches are available with a 1.75″ (44,5mm) thick Maple work surface, a 1.20″ (30,5mm) thick Laminate work surface and a 0.75″ (19,1mm) thick Phenolic work surface.
The TechBench height can be set at 1.00″ (25,4mm) increments.
TechBench (with adjustable height feature)* height range:
Maple: 34″ (863,6mm) to 38″ (965,2mm)
Laminate: 33″ (838,2mm) to 37 -3/8″ (949,3mm)
Phenolic: 32″ (812,8mm) to 36″ (914,4mm)
These heights include the four glide feet adjusted 2-1/2″ (63,5mm) from the bottom of the frame to the floor.
- TechBench maximum load capacity (evenly distributed):
  Maple: 2000 lbs. (4400 kg)
  Laminate: 2000 lbs. (4400 kg)
  Phenolic: 1200lbs. (2640 kg)

DISCLAIMER OF WARRANTIES AND LIMITATION OF LIABILITY
The information, recommendations, descriptions and safety notations in this document are based on Eaton Corporation’s (“Eaton”) experience and judgment and may not cover all contingencies. If further information is required, an Eaton sales office should be consulted. Sale of the product shown in this literature is subject to the terms and conditions outlined in appropriate Eaton selling policies or other contractual agreement between Eaton and the purchaser.
THERE ARE NO UNDERSTANDINGS, AGREEMENTS, WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE OR MERCHANTABILITY, OTHER THAN THOSE SPECIFICALLY SET OUT IN ANY EXISTING CONTRACT BETWEEN THE PARTIES. ANY SUCH CONTRACT STATES THE ENTIRE OBLIGATION OF EATON. THE CONTENTS OF THIS DOCUMENT SHALL NOT BECOME PART OF OR MODIFY ANY CONTRACT BETWEEN THE PARTIES.
In no event will Eaton be responsible to the purchaser or user in contract, in tort (including negligence), strict liability or otherwise for any special, indirect, incidental or consequential damage or loss whatsoever, including but not limited to damage or loss of use of equipment, plant or power system, cost of capital, loss of power, additional expenses in the use of existing power facilities, or claims against the purchaser or user by its customers resulting from the use of the information, recommendations and descriptions contained herein. The information contained in this manual is subject to change without notice.

TOOLS REQUIRED

3/8″ Socket wrench (not supplied)
3/8″ Socket (not supplied)
9/16″ Socket (not supplied)
1 and #2 Magnetic tip phillips head bit (not supplied)
Electric drill (not supplied)
1/2″ Open end wrench (not supplied)
1″ Open end wrench (not supplied)
Grease (supplied)

IMPORTANT SAFETY INSTRUCTIONS:

Two people are required to assemble the TechBench™.
Carefully follow instructions when adjusting the height.
A minimum of three people are required to adjust the height of the work surface when the TechBench™ is in the upright position.

CONNECTORS:

Connectors have two purposes:
(1) Connecting two Linear and/or Corner benches together.
(2) Installing a cable trough with or without connecting the benches together.

EATON TechBench Desk and Workbench System - figure 1

LINEAR BENCH ASSEMBLY (36″ [914,4mm] wide to 96″ [2438,4mm] wide

With two people, carefully unpack the Worksurface and place it finished side down on the empty carton or on a clean carpeted surface.
NOTE: Pre-drilled mounting holes in underside of Worksurface are visible.
Both sets of Upper and Lower Side Frames are pre-assembled at the factory. They must be unassembled before attaching them to the Worksurface. Remove the nuts, lock washers and carriage bolts and separate the Upper and Lower Side Frames. See figure 1.
NOTE: Do not discard this hardware. It will be used in step 6
Assemble the Stiffener to the Upper Side Frames as shown in figures 2a and 2b. Slide the “tongue” at the end of the Stiffener into the slots on the top of the Upper Side Frames. Align the holes in the tongue with the holes in the top of the frame and secure using two 1/4″-20 x 1/2″ long hex head screws. See figure 2b. Secure the gusset to the Stiffener using four 1/4″- 20 x 1/2″ long hex head screws.
Assemble Gusset Mounting to Upper Side frames using four 1/4″-20 x 1/2″ long hex head screws.
Attach he Upper Frame assembly to the Linear Worksurface. Refer to charts on page 9 for types of hardware used for specific Worksurface types.
Reassemble the Lower Side Frames to the Upper Side Frames using the carriage bolts, washers and nuts previously removed in step 2. Adjust the Lower Side Frames for the desired height of the TechBench™ and re-install the hardware as shown in figure 6a.
NOTE: If installing Connector Brackets, see figures 7a,7b, 7c and 7d before reinstalling the Lower Side Frames.
Install the 4″ Back Panel to the lower hole patterns in the Lower Side Frames using six 1/4″-20 x 1/2″ long hex head screws. See figure 6a.
Adjust each Glide Foot to meet a nominal dimension of 2-1/2″. See figure 7b. While holding the Glide Foot with a 1/2″ open end wrench, tighten the check nut with a 1″ open end wrench.
With a minimum of two people, carefully turn the TechBench™ assembly right side up.

LEVELING

Level the TechBench™ by adjusting the levelers as required.

LINEAR BENCH ASSEMBLY (24″ wide and 30″ wide)

With two people, carefully unpack the worksurface and place it finished side down on the empty carton or on a clean carpeted surface.
NOTE: Pre-drilled mounting holes in underside of worksurface are visible.
Both sets of Upper and Lower Side Frames are preassembled at the factory. They must be unassembled beforeattaching them to the worksurface. Remove the nuts, lock washers and carriage bolts and separate the Upper and Lower Side Frames. See figure 8.
NOTE: Do not discard this hardware. It will be used in step 6.
NOTE: The 24″ wide and 30″ wide TechBenchs do not have Stiffeners.
Assemble four Gusset Adapters to the Worksurface. See figure 9. Refer to charts on page 12 for type of hardware used for specific Worksurface types.
Assemble the Upper Side Frames to the Gusset Adapters using the 1/4″-20 x 1/2″ hex head screws provided. See figure 10.
Attach the Upper Side Frames to the worksurface. See figure 10. Refer to charts on page 12 for type of hardware used for specific Worksurface types.

SC RFIN CHART-1 APJNATF

SCREW CHART- MAPLE

SCREW CHART-PHENOLIC

Note: Stiffener quantities with an Asterisk ( °) include 2 screws for Gusset Adapters.

Reassemble the Lower Side Frames to the Upper Side Frames using the carriage bolts, washers and nuts previously removed in step 2. Adjust the Lower Side Frames for the desired height of the TechBench™ and re-install the hardware as shown in figure 11a.
Install the 4″ Back Panel to the lower hole patterns in the Lower Side Frames using six 1/4″-20 x 1/2″ long hex head screws. See figure 11a.
Adjust each Glide Foot to meet a nominal dimension of 21/2″. See figure 11b. While holding the Glide Foot with a 1/2″ open end wrench, tighten the check nut with a 1″ open end wrench.
With a minimum of two people, carefully turn the TechBench™ assembly right side up.

LEVELING

Level the TechBench™ by adjusting the levelers as required.

CORNER BENCH ASSEMBLY

With two people, carefully unpack the Worksurface and place it finished side down on the empty carton or on a clean carpeted surface. NOTE: Pre-drilled mounting holes in underside of worksurface are visible.
Both sets of Upper and Lower Side Frames and the Upper and Lower Corner Post are pre-assembled at the factory. They must be unassembled before attaching them to the Worksurface. Remove the nuts, lock washers and carriage bolts and separate the Upper and Lower Side Frames and Upper and Lower Corner Post. See figure 12a and 12b.
NOTE: Do not discard this hardware. It will be used in step 19.
Assemble the Stiffeners to the Upper Side Frames and Upper Corner Post as shown in figures 13. Slide the “tongue” at the end of the Stiffeners into the slots on the top of the Upper Side Frames. See Detail A. Align the holes in the tongue with the holes in the top of the frame and secure using two 1/4″-20 x 1/2″ long hex head screws. Secure the gusset to the Stiffener using four 1/4″- 20 x 1/2″ long hex head screws.
Slide the “tongue” onto the top of the Upper Corner Post and align the holes in the tongue with the holes in the top of the post and secure using two 1/4″-20 x 1/2″ long hex head screws. See Detail B. Secure the gusset to the Stiffener using four 1/4″-20 x 1/2″ long hex head screws.
Assemble two Gusset Adapters to the Worksurface using two #10 x 5/8″ Phillips head screws. See figure 14.
Turn the Upper Frame assembly over and position it on the worksurface as shown in figure 15.
Attach the Upper Frame assembly to the Corner Worksurface using the hardware provided.
For Laminate Worksurfaces, refer to figure 16.
For Maple Worksurfaces, refer to figure 17.
For Phenolic Worksurfaces, refer to figure 18.
Reassemble the Lower Side Frames and Upper Corner Post using the carriage bolts, washers and nuts previously removed in step 2. Adjust the Lower Side Frames and Lower Corner Post for the desired height of the TechBench™ and re-install the hardware as shown in figure 19a. NOTE: Connectors are installed in the same manner as the Linear benches with the exception of the Corner Connector. See figure 20.
Install the 4″ Back Panel to the lower hole patterns in the Lower Side Frames using six 1/4″-20 x 1/2″ long hex head screws. See figure 19a.
Adjust each Glide Foot to meet a nominal dimension of 2-1/2″. See figure 19b. While holding the Glide Foot with a 1/2″ open end wrench, tighten the check nut with a 1″ open end wrench.
With a minimum of two people, carefully turn the TechBench™ assembly right side up.

LEVELING

Level the TechBench by adjusting the levelers as required.

Eaton
1000 Eaton Boulevard
Cleveland, OH 44122
United States
Eaton.com
© 2018 Eaton
All Rights Reserved
Printed in USA
Publication No. IB210002EN
May 2018
Eaton
160 Gold Star Boulevard
Worcester, MA 01606
United States
800-225-7348
508-852-4300
Eaton.com/compass
Eaton is a registered trademark.