WICKED AUDIO 2OU9K0IHEC2X Driftr True Wireless Bluetooth 5.0 Earbuds Instruction Manual

OU9K0IHEC2X Driftr True Wireless Bluetooth 5.0 Earbuds
Instruction Manual DRIFTR

DRIFTR EARBUDS

DRIFTR CHARGING CASE

ONLY ONE EARBUD CONNECTING TO A DEVICE AT A TIME

Sync earbuds together by following the steps below:

1. Forget all “Wicked Driftr” in your device’s Bluetooth settings.
2. Turn off the Bluetooth setting on your device.
3. Replace both earbuds back into the charging case. This will reset the earbuds.
4. Remove earbuds from the charging case. The earbuds will turn on and sync together automatically.
5. Turn Bluetooth back on your device.
6. Find/Select “Wicked Driftr” on your device.

OR

1. Forget all “Wicked Driftr” in your device’s Bluetooth settings.
2. Turn off the Bluetooth setting on your device.
3. With both earbuds in the charging case, remove one earbud and press the button 5 times.
4. Return earbud to charging case.
5. Remove the second earbud from the charging case and press the button 5 times.
6. Return earbud to charging case. This will clear the earbuds’ memory.
7. Remove earbuds from the charging case. The earbuds will turn on and sync together automatically.
8. Turn Bluetooth back on your device.
9. Find/Select “Wicked Driftr” on your device.

CHARGING THE CASE

To charge the Driftr Charging Case use the included Micro USB to the USB charging cord. Connect the Micro USB (smaller side) into the Charging Case and connect the USB side to the computer or USB wall charger (not included).

CHARGING CASE STATUS LIGHTS:
Charging: Flashing Red
Fully Charged: Solid Red

EARBUD STATUS LIGHTS ON CHARGING CASE:
Charging: Solid BLUE
Fully Charged – Turns Off

EARBUD STATUS LIGHTS ON EARBUDS

Charging: SOLID RED
Fully Charged: TURNS OFF

CHARGING THE DRIFTR EARBUDS

Delicately place the Driftr earbuds into the earbud charging nests. Make sure each earbud is placed in its corresponding nest. Housing will face towards the back of the charging case. A small magnetic pull will help the earbuds fall into the correct position.
LEDs turn of when Driftr earbuds are fully charged.
The charging case will show a blue LED when the earbuds are charging.
The charging case will shut down automatically when the Driftr earbuds reach a full charge or when both the earbuds are removed from the case.

FIRST TIME USE FOR DUAL EARBUD MODE

(If you want to use a single earbud, please refer to section “Single Earbud Use”.)

1. Make sure the Driftr earbuds are charged (Please refer to the section “Charging the Driftr Earbuds”) and the Bluetooth device (phone, computer, tablet, etc.) is turned on with the Bluetooth feature enabled (this is usually found in settings).
2. Remove charged earbuds from the charging case. They will turn on and pair together automatically announcing “Power On.”
3. Both earbuds will pair together; both will announce “connected.”
4. When in dual earbud mode, either earbud can act as the Communicator. Once both earbuds are on, the communicator earbud will flash red and blue.
5. Your device will detect the Driftr’s pairing name “Wicked Driftr”. Select “Wicked Driftr” on your device to start pairing to your device.
6. The Communicator earbud will announce « Connected » when paired with your device and then the LED will slow flash blue.
7. You’re ready to go!

FUTURE USE AFTER INITIAL PAIRING THE DRIFTER TO YOUR DEVICE
(If this is the first time the Driftr earbuds are being paired to your Bluetooth device, or if the Driftr earbuds were “forgotten”, please see the “First Time Use” section.)
(If you want to use a single earbud, please refer to section “Single Earbud Use”.)

CONTINUED USE AFTER THE INITIAL PAIRING OF THE DRIFTR TO YOUR DEVICE

1. Remove buds (they will sync to each other automatically)
2. Earbuds will automatically pair to the last device it was paired to.

TURNING ON EARBUDS

There are two ways to turn on the earbuds:

1. Remove earbuds from their charging case.
2. Hold both center buttons for 1-2 seconds. (This is when the earbuds have shut down outside of the charging case.)

TURNING OFF EARBUDS

There are two ways to turn off the earbuds:

1. Place earbuds back into their charging case. They will automatically turn off.
2. Hold the center button, on either right or left earbud, for 5 seconds. You will hear a shutdown beep.

DISCONNECTED
When out of range, or if your device becomes disconnected from the earbuds, the earbuds will automatically go into pairing mode with the communicator earbud’s LED flashing Red/Blue.
PAUSE/PLAY
When both earbuds are paired to your device you can pause and play your music by using a short press on the center button with either the left or right earbud. (Please note  when using BOTH earbuds, you can perform this function using EITHER earbuds.)
NEXT/PREVIOUS
Next – Two presses on the right earbud
Previous – Two presses on the left earbud
ANSWER/HANGUP
When both earbuds are connected, answer or hang up by using a short press on the center button on either the left or right earbud.
INCOMING CALL
When receiving an incoming call, the earbuds will detect the device’s programmed ringtone (this may difier depending on your device)
You can answer by using a short press on the center button on either the left or right earbud.

LOW BATTERIES

Please consider charging your Driftr earbuds regularly when not in use to retain ample battery life in both earbuds.
When the earbuds have approximately 10% battery life the earbuds will announce “Low Charge.” After around 8 minutes the earbud will repeat the announcement and then shut off. The Communicator might lose battery life before the other earbud. At this point, you can shut off the left earbud and charge both earbuds, or choose to use the non- communicator earbud for an additional time in single earbud mode.
Please follow the instructions in the section “First Time Use- For Single Earbud Use.”

FIRST TIME USE- FOR SINGLE EARBUD USE

1. Remove one earbud, and keep the other earbuds off, and in case.
2. 2a – If earbuds have previously been connected to your device, either earbud will automatically pair in single mode.
   2b – If this is your first time connecting these earbuds to your device, “Wicked Driftr” will appear in your Bluetooth menu. Pair to « Wicked Driftr »
   Note: To return to “Dual Earbud Mode”
   Remove the second earbud from the charging case and it will automatically sync to your other earbud and pair to your device.
   Note: To switch from « Dual Earbud Mode » to « Single Earbud Mode »
   Place either earbud in the charging case or turn it off. The other earbud will continue working with your device.

PRECAUTIONS
LISTENING TO AUDIO AT EXCESSIVE VOLUMES CAN CAUSE PERMANENT HEARING DAMAGE. USE AS LOW A
VOLUME AS POSSIBLE.
Over exposure to excessive sound levels can damage your ears resulting in permanent noise-induced hearing loss
(NIHL). Please use the following guidelines established by the Occupational Safety Health Administration (OSHA) on
maximum time exposure to sound pressure levels before hearing damage occurs.
SAFE USE & HAZARD WARNINGS
90 dB SPL at 8 hours, 95 dB SPL at 4 hours, 100 dB SPL at 2 hours, 105 dB SPL at 1 hours, 110 dB SPL at 30 min, 115 dB
SPL at 15 min, 120 dB SPL: Avoid as damage may occur
IMPORTANT SAFETY INSTRUCTION
1 Read these instructions.
2 Keep these instructions.
3 Heed all warnings
4 Follow all instructions.

Attention should be drawn to the environmental aspects of battery disposal; The use of apparatus in moderate climates
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device.
Limitation of Liability Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
The device has been evaluated to meet general RF exposure requirements.
The device can be used in portable exposure conditions without restriction.
In no event, under any cause of action of a theory of liability, shall Wicked Audio Inc., its distributors, or suppliers be liable to you or any third party for indirect, incidental,  consequential, special, exemplary, or punitive damages, of any and all nature whatsoever, arising out of the use of or inability to use a product. This includes without limitation,  property damage, loss of value of the product, or any third-party products that are used in or with the Wicked Audio products, even if the Wicked Audio product has been advised of the possibility of such damages that one may encounter. Without limiting the foregoing, you understand and agree that Wicked Audio has no liability for any damages or destruction to the consumer electronics devices or other personal property that are contained inside or outside the Wicked Audio products. This includes without limitation, laptops, cellular phones, or other hand-held devices, or any loss of data contained on the foreign device. Notwithstanding any damages that you might incur for general damages in contract, tort (including negligence), or otherwise), the entire aggregate liability of Wicked Audio and any of its distributors and/or suppliers shall be limited to the amount actually paid by you for the Wicked Audio product giving rise to liability. Some states and/or jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you. The limitations of liability set forth above shall apply to the maximum extent permitted under applicable law.

MODEL #: WI-TW215X
IC: 20526-WITW215X
FCC: 2AFM7WI-TW215X
LIMITED ONE-YEAR WARRANTY
Keep your receipt to obtain warranty service. Go to
www.wickedaudio.com for more details.
Developed in Utah, U.S.A.
Made in China

References

• Wicked Audio – Wicked Audio, Inc.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>