PROBRITE LED50-PC-GR LED Bulb Area Barn Light User Guide

June 5, 2024
PROBRITE

PROBRITE LED50-PC-GR LED Bulb Area Barn

SAFETY INFORMATION

IMPORTANT
THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE NATIONAL ELECTRICAL CODE AND LOCAL BUILDING CODES BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.

PRECAUTIONS

  • Please read and understand this entire manual before attempting to assemble, install, or operate this light fixture.
  • This light fixture requires a 120 Volt AC power source.
  • Some codes require installation by a qualified electrician.
  • This light fixture must be properly grounded.
  • Make sure connections are secure using wire nuts, crimp-on lugs or other approved connecting devices
  • This light fixture should be installed outdoors to a wall or a pole.\

PRE-INSTALLATION

PLANNING INSTALLATION
Before installing the light fixture, ensure that all parts are present. Compare parts with the Hardware Included and Package Contents sections. If any part is missing or damaged, do not attempt to assemble, install, or operate this light fixture.

SPECIFICATIONS

PROBRITE LED50-PC-GR LED Bulb Area Barn Light-

TOOLS REQUIRED

PROBRITE LED50-PC-GR LED Bulb Area Barn Light-1

PACKAGE CONTENTS

PROBRITE LED50-PC-GR LED Bulb Area Barn Light---

HARDWARE KIT

PROBRITE LED50-PC-GR LED Bulb Area Barn Light----

FOR BEST RESULTS

Review this information to ensure a successful installation:

  • Install the light 12-30 ft. above the ground.
  • When mounting the fixture, ensure the photocell is in an area that receives daylight and is not too close to reflective surfaces in order to ensure successful Dusk-to-Dawn operation.
  • When installing two fixtures on one switch, make sure the switch is rated for at least a 1A inductive load.
  • Do NOT wire to a dimming switch.
  • When mounting to a wall, make sure the fixture is 7 in. on center away from an eave and 13 in. on center away from the inside corner of the exterior wall.

SHUT OFF ELECTRIC POWER OFF

PROBRITE LED50-PC-GR LED Bulb Area Barn Light-5

  • Verify wall switch is in OFF position (fig 4).
  • At the main electrical panel, turn off the circuit breaker that supplies power to the junction box you are working on (fig 5).
  • For screw-in type fuses, unscrew the fuse that supplies power to the junction box you are working on (fig 6).

PREPARING FOR MOUNTING THE FIXTURE

Wall Mount

  • Remove the wire guard protection plate (CJ from the arm (DJ of the fixture by loosening the screws.
  • Mark and pre-drill the three holes on the desired location of the mounting surface.

Extension Arm Mount

  • Remove the wire guard protection plate (CJ from the arm (DJ of the fixture by loosening the screws. (fig 7).PROBRITE LED50-PC-GR LED Bulb Area Barn Light-6

MOUNTING THE FIXTURE

Wall Mount

  • Attach the fixture to the wall using the three hex head bolts (AA). (fig 8)

Extension Arm Mount

  • After wiring is complete, secure the fixture on the extension arm by tightening the screws removed earlier. (fig 13)

INSTALLING THE REFLECTOR

Preparing the reflector for installation

  • Place the hooks from the bottom part of the lens reflector (E) into the holes provided in the upper part of the reflector’ s (E) rim and twist the bottom lens to fit.
  • Close the hooks by pressing them down to lock.

Attaching the reflector to the fixture

  • Install two small screws included with the reflector (E) leaving about 1/4 in. of space under the fixture head (A).
  • D Align keyholes in the reflector (E) with screw heads and rotate counterclockwise.
  • D Tighten the screws using a Phillips head screwdriver to attach the reflector (E) on the fixture head (A).

INSTALLING THE LED LIGHT

  • Install the LED light (F) inside the reflector (E) on the fixture head (A). (fig 15)

SELECT DUSK-TO-DAWN

OPTION 1: DUSK-TO-DAWN OPERATION
Dusk-to-dawn operation enables the light fixture to automatically turn ON when dark outside and turn OFF when the sun rises, thus saving you energy.

  • To enable dusk-to-dawn operation, make sure the photocell (B) is exposed to light and is unobstructed.
  • Ensure the switch powering the light fixture is turned to the ON position and leave it ON at all times to enable automatic dusk-to-dawn operation.

CARE AND CLEANING

  • Shut off main power supply before cleaning the product. To prolong the original appearance, clean the light fixture with clear water and a soft, damp cloth only.
  • Do not use abrasive cleaners or cleaners that contain alcohol. Do not apply paints, solvents, or any other chemicals on this light fixture. They could cause a premature deterioration of the finish and may void the warranty.
  • Do not spray the light fixture with a hose or power washer.

TROUBLESHOOTING

PROBRITE LED50-PC-GR LED Bulb Area Barn-tb

5-YEAR LIMITED WARRANTY

This is a limited warranty offered by Probrite for a period of five years from the date of purchase to its customers. Probrite warrants to customers that the products will be free from defects in material and workmanship. The obligation of Probrite under this warranty is limited to the provision of replacement of products and is extended to the original purchaser of the product on presenting valid purchase receipt or other proof of date of original purchase acceptable to Probrite. The receipt is required for rendering the warranty performance. Any warranty claims without original proof of purchase would not be accepted.
It should be noted that the warranty does not apply to Probrite products that have been altered or repaired by unauthorized personnel, have been subjected to neglect, abuse, misuse or accident or damages caused during shipping. Any other products not manufactured by Probrite which have been supplied, installed and/or used in conjunction with Probrite products are not covered under this warranty. Any damages caused by replacements bulbs, LEDs or corrosion or discoloration of brass components are also not covered by this warranty.

Limitation of Liability:
In no event, Probrite shall be liable for indirect, consequential, incidental or special damages, or lost profits. Probate is not liable for any claims or damage arising out of or connected with the manufacture, sale, delivery, use, maintenance and repair or modification of Probrite products, or supply of any replacement parts that, exceed the purchase price of Probrite products giving rise to a claim. Labor charges to remove or install the fixtures will not be accepted.

To Claim:
Please contact PRO BRITE customer service at 1-844-507-5651 or email support@PROBRITE.com and include your name, address and contact number, along with a copy of the purchase receipt and a brief description of the problem.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals