Dual Electronics LU43PB 3-Way High Performance Outdoor Indoor Speakers with Powerful Bass-Complete Features/Instruction Guide

Dual Electronics LU43PB 3-Way High-Performance Outdoor Indoor Speakers

with Powerful Bass

Speciifcatiosn

• BRAND: Dual Electronics
• COLOR: Black
• SPEAKER TYPE: Outdoor, Bookshelf
• MODEL NAME: Speakers
• SPEAKER SIZE: 4 Inches
• PRODUCT DIMENSIONS: 5.3 x 5.3 x 8.3 inches
• ITEM WEIGHT: 2.8 pounds

Introduction

Your studio-quality speakers can be mounted/placed in any open spot, such as beside the pool, under your patio, in the garage, or on a bookshelf; regardless of location, they will produce excellent sound quality. Extraordinary Sound The synchronized harmony of your 3-Way Component Speakers and 4-inch Woofer creates a state of accurate acoustic dispersion with deep rich-sounding bass for a truly full range of sound versatility is in its design; your speakers can be mounted in a matter of seconds in any open space and provide you with a 120-degree range of High Fidelity Sound these speakers are made for Every Season; they are coated with a UV resistant resin and placed inside an ABS enclosure.

Don’t forget to pair your LU43PB Speakers with the best-selling Dual Electronics DBTMA100 Bluetooth Amplifier for the greatest outdoor/indoor acoustic experience (sold separately). DIMENSIONS: 8.25 inches high, 5.25 inches wide, and 5.25 inches deep. High quality and dependability are guaranteed, with hassle-free parts and labor warranty, and outstanding customer service.

MOUNTING PLACEMENT

If mounting is desired. mounting both speakers on a common solid surface facing the listening area will provide the best audio results. Do NOT mount speakers on wall surfaces that have hazards concealed behind them. such as electrical wires or plumbing. Always mount speaker on surfaces that are sturdy enough to support the speakers’ weight, and make sure they cannot fall or cause injury.

SPEAKER PLACEMENT

Your speakers can be placed in many convenient locations in your home or patio area – as stereo pairs on either side of your receiver as surround speakers in home theater surround sound systems – in your computer room to enhance the multimedia experience or as remote speakers.

WALL AND CEILING

For wall and ceiling applications. DUAL mounting brackets Placement are included. In addition. the LU43 has a rear inset keyhole for surface hanging. and the larger LU53 has two 1/4-20 brass inserts incorporated into the rear of the enclosure if aftermarket mounting systems will be used.

PLACEMENT AND MOUNTING OF SPEAKERS

OUTDOOR PLACEMENT

The DUAL LU43 and LU53 have been tested for environmental usage and are weather resistant. but not waterproof. Occasional moisture will not affect performance. The speakers should be allowed to ventilate and dry after water exposure. The speakers can be placed permanently outdoors for year-round enjoyment. To maximize speaker life. position in areas protected from the elements. such as the underside of eaves and overhangs. Popular locations include decks. gazebos. porches. atriums. garages. and covered spa areas.  For temporary placement, remove the speaker from the mounting brackets and replace the thumbscrews to maintain stability if placing the speakers on an end.

Both the LU43 and LU53 speakers have a DUAL logo that can be rotated. The logo is located on the face of the grille in the event a vertical installation is needed. The logo is spring-loaded. Use gentle force when adjusting the logo to a new orientation. To rotate the logo. elevate two ends of the logo equally by placing your nail under and lifting lightly. While the logo is elevated. turn the logo to the desired orientation and release.

MOUNTING YOUR SPEAKERS

For ease of installation. the DUAL LU43 and LU53 include an easily removable mounting bracket. Once mounted, the bracket allows the speaker to be pivoted to its ideal location. The included thumb screw knobs will hold the selected speaker position when properly tightened. Avoid over-tightening the knob. Before attempting the installation carefully evaluate the mounting surface. making sure that its composition and construction are strong enough to support the load safely. If you are unsure about the type of mounting hardware for your installation. consult a professional contractor or a knowledgeable hardware store. The anchors and screws to attach the speakers are not included and must be purchased separately. The hardened steel brackets are suitable only for attaching the speaker to walls or ceilings constructed of solid wood. brickwork. concrete. Hollow buildings block or wood studs.

Do not mount the bracket to a non-reinforced plaster sheetrock gypsum board). Once the bracket is secure, reattach the speaker using the thumbscrews included.

CONNECTING YOUR SPEAKER

Speaker Wire-1ypical speaker wire has a pair of separate speaker Wires with insulating jackets that are molded together. Dual recommends the use of two- conductor 18- gauge speaker wires to connect your speakers to your receiver Measure enough wire to reach from your receiver to each speaker plus additional length to allow moving the speakers or receiver without having to disconnect the wires. When connecting the speakers in a stereo configuration, the wire length should be similar. One length should not be dramatically longer or shorter than the other. Maintaining similar wire lengths will provide superior sound quality.

Polarity Speaker wires are marked for polarity consistency so that you can determine the positive and negative identity of the individual wires within the molded pair insulation. Polarity is shown by either a color stripe on the insulation. by ridges molded into one side of the insulation, the color of the insulation case around the wire, or by the color type or colors of the wires/wire itself (copper or silver).

IMPORTANT
Always connect the speaker wire using the positive (+) terminal on the receiver to the positive (+) terminal, and the negative (-) terminal on the receiver to the negative (-) terminal. All speakers in a system must be connected with the same respective polarity. The speaker inputs are located on the rear-mounted terminal cup on the back of the speaker.

TERMINAL TYPE
 The LU43 utilizes a push-pin design. Gently depress the colored lever and insert the stiped end of the wire directly into the opening located in the center of the input housing.

CONNECTING SPEAKERS

YOUR SPEAKERS

The speaker wire must be securely connected and tightened properly to the speaker inputs. Do not over-tighten. Do not allow the positive and negative speaker wire from the receiver to make contact. as this will cause a short.It is recommended that the wire insulation be stripped back approximately 3/8″. allowing the wire conductor to make a proper connection. Make sure that the wire insulation is stripped back far enough so that the bare speaker wire will make a proper connection to the metal clip inside the terminal and be securely held in place. This can be confirmed visually.

Frequently Asked Questions

• How would I power them if I wanted to hang them from my bedroom ceiling?
  A power supply is not required for stereo speakers. Speaker wires are used to connect them to your stereo system/receiver.

• Is it true that the speakers are Bluetooth?
  They won’t be Bluetooth until you buy the Bluetooth amp for them, which is the only way they’ll be. Alternatively, purchase a Bluetooth receiver to connect them to.

• Is there an aux port on it?
  There aren’t just red and black receptacles for speaker wire.

• How do these speakers function?
  Electrical energy is converted into mechanical energy (motion) through speakers. A current is passed through the voice coil in the speakers, creating an electric field that interacts with the magnetic field of the speaker’s permanent magnet. Charges that are similar repel each other, while charges that are dissimilar attract.

• Is it possible to connect them to a Samsung UN65JS8500F television?
  Only if the television had a built-in amplifier that could power external speakers.

• Is it possible to utilize one of these speakers as the center channel in a 5.1 setup?
  I’m not sure what your setup is, but I can tell you that these are monitor speakers only. Ideal for a tiny studio or workplace at home. They’re powerful enough to serve as low background music for a small gathering, but if you want to get people dancing, you’ll probably blow them up as I did

• Is an amplifier required for these?
  I connected it directly to my amplifier. If you wish, you can.

• Is it possible to connect my XM radio to these?
  Absolutely! That’s how I do it!

• 4 or 6-ohm impedance Is it 12 ohm or 8 ohms if I connect in series 2?
  Impedance in series adds up, however when two speakers are connected to the same input, the impedance divides since the speakers are parallel, resulting in a reduced impedance.

https://www.manualshelf.com/manual/dual/lu43pb/use-and-care-manual- english/page-6.html 

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>