AURORA LIGHTING Solar LED Batten Light User Manual
- June 5, 2024
- AURORA LIGHTING
Table of Contents
SOLAR LED BATTEN LIGHT
User Manual
Fix the two metal clips into position and attach them to the surface. It is recommended that each clip is positioned approximately 20CM from each end of the Batten Light. Caution: Ensure correct anchor sleeves are used for surface material. Please see the package contents before installation.
|
---|---
Insert Tensioning Bolt and attach the Batten Light to the metal clips.| Using
a screwdriver, secure each clip onto the Batten Light with the Tensioning
bolt.
Note: This is only to secure the batten light so it cannot be removed –
Do not over-tighten.
|
Connect the MC4 Connectors to the Solar PV panel. Note: A matching pair of MC4
connectors is included in the contents of this package. If the Solar PV Panel
does
Do NOT have an identical pair of MC4 connectors, replace them with the ones
provided to guarantee a weather-tight connection.| Power ON the Batten Light.
A RED signal light can be seen at the sensor end of the Batten Light.
Program the light to best suit your installation.
Please refer to the setup guide of the manual properly.
Light will work at 50% power when nobody is there and 100% power for 60mins
when the sensor is
MANUAL OF KEY FUNCTION
MAGIC remote control is used to change the program of the light. there are two sections, one is for setting modes. the other is to change the time. This remote controller is able to meet most of the requirements for different lighting situations. Light will work on” AUTO” mode that will turn ON/OFF automatically upon day and night as the default setting. ON/OFF key is to work in the daytime with hand operation.
| ON/OFF override button. 100% Light Output
---|---
| Auto Function (Not Used). By Default Auto Function is programmed ON.
(Auto OFF During Day, Auto ON During Night)
| Test Function. Light will operate for 20 seconds.
(The green indicator light will operate inside the end-cap if the battery is
low / over-discharged.)
A. Light Output 0%.
When sensor triggered – Light Output 100% for 1 minute.
B. Light Output 30%.
When sensor triggered – Light Output 100% for 1 minute
C. Light Output 50%.
When sensor triggered – Light Output 100% for 1 minute.
D. Light Output 100% (First 6 hours). Light Output 50% (Second 6 hours) – When
sensor is triggered – Light Output 100% for 1 minute.
- Helpful Hint. Press “D” and a Time Setting (e.g.7H) = 100% for 3.5 hours then 50% for next 3.5 hours + 100% with sensor.
5-6-7-8-9 are similar time function as 1-2-3-4….
- M6*16 Screws .
- This is to fix to solar panel
- M6*16 Screws .
- Can fix in different holes for different mounting angles.
- M8*16 Screws.
NOTICE
Please note the brackets for the left and right sides are different, make sure
it is well-assembled properly.
GENERAL OPERATION
RED/GREEN/BLUE Status Light
- After turning the batten light ON. A Red/Green/Blue status light will cycle for two seconds and then stop. This signals the batten light system is OK and will work
in the default operation of 0%+100% sensitivity power surface material. Please see the package contents before installation. - After 1 minute of being ON a BLUE light will start to flash (slowly). This signals the BattenPRO is now in a charge state and the solar panel is connected and operating as it should.
IMPORTANT:
If after 1 minute the BLUE light flashes (fast), check the polarity connection between the solar panel and BattenPRO. “+ to +” and “- to -“. And that a firm contact is made.
TESTING
To simulate the batten light operation during daylight hours. Disconnect or cover the Solar Panel (This signals no voltage present to the batten light, and will simulate night operation) – Now turn the batten light ON. The Red/Green/Blue status lights will cycle for two seconds then stop. After 40 seconds, move in the proximity of the microwave sensor, once detected by the microwave sensor the light will operate with 100% light output (default setting) then will turn off automatically after 30 seconds.
PLEASE NOTE:
The default setting is Mode A with 0% power (No Light Output) and 100% Light Output when a person is in proximity. You can press buttons B, C, or D or 20%/40%/80% to turn the light ON immediately to check the light condition.
USING THE REMOTE
The remote uses microwave (IR) technology and needs to be used in the same way as a TV –You must point the remote directly at the BattenPRO to send a command. After pressing a button on the remote control, you will see a GREEN + BLUE light for two seconds. That signals a command has been received successfully.
Note: Refer to manual for remote control functions and programming.
FAULT FINDING
BLUE LIGHT NOT VISIBLE / WORKING
- After doing steps under GENERAL OPERATION and the BLUE light is NOT giving any signal /flashing. Double-check the connection between the BattenPRO and solar panel is a firm connection and the polarity is correct.
- Meter the voltage from the solar panel to the MC4 connectors. Ensure the voltage is no less than
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>