EShine 10 inch Rechargeable LED Light Hand Wave Activation User Manual
- June 5, 2024
- ESHINE
Table of Contents
- EShine 10 inch Rechargeable LED Light Hand Wave Activation User Manual
- Packaging contents:
- Precautions
- Technical specifications
- 1. Installation
- 2. Charging
- To check the battery level:
- 3. Operation and Timer Settings
- 4. Brightness control
- 5. Warranty
- What does this limited warranty cover?
- What will we do to correct problems?
- How long does the coverage last?
- What doesn’t this limited warranty cover?
- What do you have to do?
- Read More About This Manual & Download PDF:
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
EShine 10 inch Rechargeable LED Light Hand Wave Activation User Manual
Thank you for choosing our EShine brand product. Before turning on the
lights, read the instructions and store them for future reference.
Packaging contents:
- 1X LED hand wave activated light
- 1X Micro USB cable
- 1X 3M adhesive magnetic strip
- 2X screws
Precautions
- Check the lamp carefully before installing.
- Do not open the LED lamp.
- Do not install the light in wet, high-temperature or vent areas to avoid affecting normal use.
- Do not attempt to repair or disassemble the lamp. Doing so will void the warranty.
- Use this product indoors only!
- Warning! The packaging contains small parts. Not for children.
Make sure there are NO objects within 4 inches from the sensor (for example: wall, wood board, any supplies, cabinet lip, etc).
Technical specifications
Dimensions | 42(W) x 14.6(H) x 240 (L) mm |
---|---|
LED quantity | 33 pcs LED |
Material | Plastic and Aluminum |
Battery capacity | 1300 mAh |
Charging time | 2:30-3:30 hours |
Power | 1.5W |
Dimmable | Yes, Touchless Dimming |
Color temperature | 3200K/5000K |
Rated LED life | >30,000 h |
Nominal luminous flux | 100lm |
Angle | 120° |
Protection | IP20 |
Protection class | III |
Operating temperature | -20° C to + 45° C |
1. Installation
There are 3 methods of installation to choose from:
- Simply attach to any iron surface, as light has built in magnets (see pic 1).
- Attach magnetic strip to any surface using the included 3M adhesive (see pic 1). Then attach light to the magnetic strip.
- Attach magnetic strip to most surfaces using screws (see pic 2).
Pic. 1. Installation using built-in magnet
Pic. 2. Magnetic strip installation using screw
2. Charging
You will need to charge the EShine light if it is dim. To charge the light or for continuous operation:
- Plug the provided USB cable into the USB port on the device.
- Plug the other end of the cable into a power source. You can use a phone adapter to charge the lights or an outlet with a USB connection.
- Red charging indicators will blink while charging and will light up solid when a full charge is achieved.
To check the battery level:
-
Press the Timer button for at least 2 seconds.
-
Look at the red charging indicators.
-
If the all indicators are flashing, the batery is low.
-
Each lit red indicators means 25% charged. So when all 4 indicators are lit, the device is 100% charged.
-
Always unplug the charger when the battery is fully charged to prolong the life of your battery.
Note: It takes 2:30-3:30 hours to fully charge the battery.
Caution: Use a power source of at least 1 amp to charge the LED light.
3. Operation and Timer Settings
Press the Power button for at least 2 seconds to turn the light ON or OFF. After that, you can simply wave your hand over the sensor to turn the light ON or OFF.
Note: Make sure there are no objects within 4 inches from the sensor (walls, boards, supplies, cabinet lips, etc). If you install the LED bar with the sensor close to an object or wall, the LED bar will not operate properly.
Light automatically turns OFF after 5 minutes. This time can be adjusted. Press the Timer button to change the automatic shutoff time setting (red indicators show time setting):
- 5-minute delay (default) – 1 RED indicator ON
- 3-minute delay – 2 RED indicators ON
- 1-minute delay – 3 RED indicators ON
- No Timer (must wave hand to turn ON/OFF) – 4 RED indicators ON
4. Brightness control
Your EShine light comes with touchless dimming control. Hold your hand under
the sensor for more than 1 second to adjust brightness of all lights from 10%
to 100% level. When you turn the
light off, it will remember your last used brightness level. To reduce battery
consumption, use the lowest brightness level necessary.
5. Warranty
The EShine LED Lighting Kit comes with a limited 3-Year warranty.
What does this limited warranty cover?
This Limited Warranty covers any defects in material or workmanship under normal use during the Warranty Period.
What will we do to correct problems?
During the Warranty Period, we will repair or replace, at no charge, products
or parts of a product that prove defective
because of improper material or workmanship, under normal use and maintenance.
How long does the coverage last?
The Warranty Period for this LED lighting kit is 3 years from the date of purchase.
What doesn’t this limited warranty cover?
This limited warranty does not cover any problem caused by condition, malfunction or damage that is not a result of a defect in material or workmanship.
What do you have to do?
To make use of the warranty service, you must first contact us. We will
determine the problem and the most appropriate solution for you.
EShine®
Web: www.eshinestore.com
Email: service@eshinestore.com
Read More About This Manual & Download PDF:
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>