ESHINE ELB600MDC 24 inch Rechargeable Battery Powered Motion-Activated LED Under User Manual

June 5, 2024
ESHINE

ESHINE - logo ELB600MDC 24-inch Rechargeable Battery Powered
Motion-Activated LED Under
User Manual

Thank you for choosing a product from the brand shine. Before turning on the lights, read the instructions and store them for future reference.
Packaging content:

  • 1X LED motion sensor light
  • 1X USB cable
  • 1X 3M adhesive magnetic strip
  • 2X screws

ESHINE ELB600MDC 24 inch Rechargeable Battery Powered Motion-Activated LED
Under

Precautions

  • Please check the lamp carefully before installing it.
  • Please do not open the LED lamp.
  • Do not install the light in wet, high-temperature, or vent areas to avoid affecting normal use.
  • Please do not retrofit the lamp within the warranty period
  • Please use this product indoors only!
  • Warning! The packaging contains small parts. Not for children.

Technical specifications

Dimensions 42(W) x 14.6(H) x 600 (L) mm
LED quantity 96 pcs LED
Material Plastic and Aluminum
Battery capacity 4800 mAh
Charging time 5:00-6:00 hours
Power 4W
Dimmable Yes, 3 brightness levels
Color temperature 3200K/5000K
Rated LED life >30,000 h
Nominal luminous flux 2501m
Angle 120°
Protection IP20
Protection class III
Operating temperature -20° C to + 45° C

Installation

We have 3 methods of installation:

  1. Simply attach to any ironwork surface as light has built-in magnets (see pic 1).
  2. Attach a magnetic strip to any surface using 3M adhesive (see pic 1).
  3. Attach a magnetic strip to any surface using screws (see pic 2).

ESHINE ELB600MDC 24 inch Rechargeable Battery Powered Motion-Activated LED
Under - figure 1 Pic. 1. Installation using a built-in magnetESHINE
ELB600MDC 24 inch Rechargeable Battery Powered Motion-Activated LED Under -
figure 2

Pic. 2. Magnetic strip installation using screw

Charging

Checking battery level – Hold dimmer switch for more than 2 seconds. Each red charging indicator is 25% power.
Charging – Charging indicators will blink until fully charged.
Battery level will show automatically when charging.
Fully charged – All four charging indicators are lit, 100% charged.
Continuous operation – You can also connect the light to a USB power source and keep it ON constantly without recharging.

Charging time: 5:00-6:00 hours
The current of the power source should be more than 1A for charging (for example you can use your phone adapter to charge the lights or an outlet that has a USB connection etc.)
If you see the LED has dimmed it means the battery is LOW.
IMPORTANT: The battery of the LED Bar has overcharge protection but for longer battery life, we recommend unplugging the charger as soon as it is fully charged.

Choose Mode

  1. Mode 1 (Always On/Turning light ON): Light for a long-light situation.
    In this mode, the lamp operates continuously.
    High battery consumption.
    Long press the switch for about 2 seconds to turn on the light and it enters into Always ON Mode.

  2. Mode 2 (Motion & Light Sensor): Under dark enough conditions, the light automatically turns ON when motion is detected within 3 meters, and automatically turns OFF after  20 seconds (adjustable) of inactivity. Low battery consumption.
    After turning ON the light, short press the power switch, the green indicator flashes for 1 second, it enters into Motion & Light Sensor Mode.

  3. Mode 3 (Only Motion Sensor): Automatically turns ON when motion is detected within 3 meters, automatically turns OFF after 20 seconds (adjustable) of inactivity. You may use this model in the daytime. Low battery consumption.
    After turning ON the light, short press the power switch twice, the red indicator flashes for 1 second, it enters into Motion Only Sensor Mode.

  4. Mode 4 (Setting Mode): Here you can adjust delay time using the dimmer switch button (see details at point 4 of the manual).
    After turning ON the light, short press the power switch three times, and red and green indicators flash together, it enters into Setting Mode.

  5. Mode 5 (OFF): Long press the switch for about 2 seconds to turn off the light.
    ESHINE ELB600MDC 24 inch Rechargeable Battery Powered Motion-Activated LED
Under - figure 4

IMPORTANT: The sensor performance can be influenced slightly by temperature and movement speed.

Setting Mode – Delay Time Adjustment

Delay time is after how many seconds the light will turn OFF if no movement is detected.
To change the delay time, you need to enter into SETTING MODE-short press the “POWER SWITCH” button 3 times and you should see GREEN+RED indicator lights ON together. This means you are in a SETTING MODE.
20-second delay (factory setting) – once you enter the setting mode you will see 1 RED BATTERY INDICATOR is lit which means it is on a 20-second delay. To change it you need to short press the DIMMER switch 40-second delay – short press the “Dimmer Switch” button, and 2 RED indicator lights come ON.
60-second delay – short press the “Dimmer Switch” button and 3 RED indicator lights come ON.
120-second delay – short press the “Dimmer Switch” button and 4 RED indicator lights come ON.
After you choose the desired delay time, short press the “POWER SWITCH” button to the GREEN indicator (Motion & Light Sensor) or the RED indicator (Only Motion  Sensor).

Brightness control

Adjust brightness via the left button:

  • 30% Brightness: Short press the dimmer switch
  • 65% Brightness: Short press the dimmer switch twice
  • 100% Brightness: Short press the dimmer switch three times

You can significantly extend the battery life using the brightness level control. Below is the time chart to work in the “Always On” mode:

  • 100% brightness: 4:30 hours
  • 65% brightness: 6:30 hours
  • 30% brightness: 15:00 hours

IMPORTANT: Light has a memory function and it will remember the last brightness setting.

Warranty

EShine LED Lighting Kit comes with a Limited 3-Year Warranty.

What does this limited warranty cover?
This Limited Warranty covers any defects in material or workmanship under normal use during the Warranty Period.
What will we do to correct problems?
During the Warranty Period, we will repair or replace, at no charge, products or parts of a product that proves defective because of improper material or workmanship, under normal use and maintenance.
How long does the coverage last?
The Warranty Period for this LED lighting kit is 3 years from the date of purchase.
What does this limited warranty not cover?
This Limited Warranty does not cover any problem that is caused by conditions, malfunctions, or damage not resulting from defects in material or workmanship
What do you have to do?
To make use of the warranty service, you must first contact us to determine the problem and the most appropriate solution for you.

EShine®
Web: www.eshinestore.com
Email: service@eshinestore.com

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals