HEART ERF-HR4132A-F Tiris Proximity Tag Write Controller User Manual

HEART ERF-HR4132A-F Tiris Proximity Tag Write Controller

Introduction

Thank you for purchasing the ERF‐HR4132A‐F CIDRW System.
Please observe the following points when operating the ERF‐HR4132A‐F:

• Please read and understand the content of this manual before using the system.
• After reading this manual, store it in a handy location for easy reference whenever necessary.

FITTINGS

• Core : King-Core KCF-65-B x 1

Precautions in using the product

READ AND UNDERSTAND THIS DOCUMENT

Please read and understand this document before using the products. Please consult your HEART TECH representative if you have
any questions or comments.

WARRANTY
HEART TECH’s exclusive warranty is that the products are free from defects in materials and workmanship for a period of one year (or other period if specified) from date of sale by HEART TECH.
HEART TECH MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, REGARDING NONINFRINGEMENT, MERCHANTABILITY, OR FITNESS FOR PARTICULAR PURPOSE OF THE PRODUCTS. ANY BUYER OR USER ACKNOWLEDGES THAT THE BUYER OR USER ALONE HAS DETERMINED THAT THE PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE. HEART DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED.

LIMITATIONS OF LIABILITY
HEART TECH SHALL NOT BE RESPONSIBLE FOR SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS BASED ON CONTRACT, WARRANTY, NEGLIGENCE, OR STRICT LIABILITY.
In no event shall responsibility of HEART TECH for any act exceed the individual price of the product on which liability is asserted.
IN NO EVENT SHALL HEART BE RESPONSIBLE FOR WARRANTY, REPAIR, OR OTHER CLAIMS REGARDING THE PRODUCTS UNLESS HEART’S ANALYSIS CONFIRMS THAT THE PRODUCTS WERE PROPERLY HANDLED, STORED, INSTALLED, AND MAINTAINED AND NOT SUBJECT TO CONTAMINATION, ABUSE, MISUSE, OR INAPPROPRIATE MODIFICATION OR REPAIR.

SUITABILITY FOR USE
THE PRODUCTS CONTAINED IN THIS DOCUMENT ARE NOT SAFETY RATED. THEY ARE NOT DESIGNED OR
RATED FOR ENSURING SAFETY OF PERSONS, AND SHOULD NOT BE RELIED UPON AS A SAFETY COMPONENT
OR PROTECTIVE DEVICE FOR SUCH PURPOSES. Please refer to separate catalogs for HEART TECH ‘s safety rated
products.
HEART TECH shall not be responsible for conformity with any standards, codes, or regulations that apply to the combination of products in the customer’s application or use of the product.
At the customer’s request, HEART TECH will provide applicable third party certification documents identifying ratings and limitations of use that apply to the products. This information by itself is not sufficient for a complete determination of the suitability of the products in combination with the end product, machine, system, or other application or use.
The following are some examples of applications for which particular attention must be given. This is not intended to be an exhaustive list of all possible uses of the products, nor is it intended to imply that the uses listed may be suitable for the products:

• Outdoor use, uses involving potential chemical contamination or electrical interference, or conditions or uses not described in this document.
• Nuclear energy control systems, combustion systems, railroad systems, aviation systems, medical equipment, amusement machines, vehicles, safety equipment, and installations subject to separate industry or government regulations.
• Systems, machines, and equipment that could present a risk to life or property.
• Please know and observe all prohibitions of use applicable to the products.

NEVER USE THE PRODUCTS FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT THE HEART PRODUCT IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE
OVERALL EQUIPMENT OR SYSTEM.

PERFORMANCE DATA
Performance data given in this document is provided as a guide for the user in determining suitability and does not
constitute a warranty. It may represent the result of HEART TECH’s test conditions, and the users must correlate it to actual application requirements. Actual performance is subject to the HEART TECH Warranty and Limitations of Liability.

CHANGE IN SPECIFICATIONS

Product specifications and accessories may be changed at any time based on improvements and other reasons. It is our practice to change model numbers when published ratings or features are changed, or when significant construction changes are made. However, some specifications of the product may be changed without any notice. When in doubt, special model numbers may be assigned to fix or establish key specifications for your application on your request. Please consult with your HEART TECH representative at any time to confirm actual specifications of purchased products.

DIMENSIONS AND WEIGHTS

Dimensions and weights are nominal and are not to be used for manufacturing purposes, even when tolerances are shown.

ERRORS AND OMISSIONS
The information in this document has been carefully checked and is believed to be accurate; however, no responsibility is assumed for clerical, typographical, or proofreading errors, or omissions.

PROGRAMMABLE PRODUCTS
HEART TECH shall not be responsible for the user’s programming of a programmable product, or any consequence thereof.

COPYRIGHT AND COPY PERMISSION

• This document shall not be copied for sales or promotions without permission.
• This document is protected by copyright and is intended solely for use in conjunction with the product. Please notify us
• before copying or reproducing this document in any manner, for any other purpose. If copying or transmitting this
• document to another, please copy or transmit it in its entirety.

FCC WARNINGS

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

• This device may not cause harmful interference and followed, read and understood by all persons working with the device (especially the safety information)
• This device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, in accordance with part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual,may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception – this can be determined by turning the equipment off and on -the user is encouraged to try to correct the interference using one or more of the following measures:

• Reposition or relocate the receiving antenna.
• Increase the distance between the equipment and the receiver.
• Connect the equipment to an outlet to a circuit other than the one to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for assistance.

FCC ID : 2AB67-ERF-HR4132A-F
Compliance with :
FCC Code of Fedral Requlations,Part 15 Subpart C, Section §15.205 FCC Code of Fedral Requlations,Part 15 Subpart C, Section §15.209
WARNING

Dimensions

Installation

CID/Data Read/Write Controller
Mount the CIDRW Controller with the two M3 – M4 screws .

Note：

• Tighten the M3 – M4 screws with a torque not exceeding 1.2 N·m.
• Do not apply organic solvents used with screw locking agents at the locations where the screws are inserted.

Antenna
Stick antenna

Rectangular antenna

Champ Core Installation Instructions

Transmission Area (information only):

• Antenna : Stick antenna

• Tag : TEXAS INSTRUMENTS 32mm Glass Transponder part number RI‐TRP‐DR2B
  The transmission area diagram going through the center of the antenna and indicated on a flat surface vertical to the antenna surface is as indicated below.

• Antenna : Rectangular antenna

• Tag : TEXAS INSTRUMENTS 32mm Glass Transponder part number RI‐TRP‐DR2B
  The transmission area diagram going through the center of the antenna and indicated on a flat surface vertical to the antenna surface is as indicated below.

General specifications

terminals
Current consumption @12VDC| Average 50mA ;**

Peak 160mA

| Approx. 2A max, with rush current
Transmitting Radio Frequency| Typical 134.2KHz| FSK
Transponder Type| TIRIS Tag| Single & Multi page Transponder
Operating ambient

temperature

| ‐10 ~ +70 ℃| No freezing
Operating ambient humidity| 10 ~ 85%RH| No dew condensation
Storage ambient temperature| ‐20 ~ +85 ℃| No freezing
Storage ambient humidity| 5 ~ 95%RH| No dew condensation
Communication interface| RS‐232C| 9600 bps (fixed), E.8.1 (fixed)
Weight| 450g MAX.| No freezing
Dimensions| 147 × 110 × 32 mm| Except for protrusions on connectors
Mounting system| Secured with four M4 screws.| Use the enclosed washers.

Communication interface specification

4‐40 UNC lock screws
Communication standard| RS‐232C
Synchronization| Asynchronous mode, start‐stop synchronization
Communications control standard| PLC/ASC‐II protocol for ERF‐HR4132A‐F CID Read/Write controller only
Baud rate (fixed)| 9600 bps**

Character format (fixed)

| Start bit| Data bit| Parity bit| Stop bit| Total
1| 8| Even| 1| 11
Error control| FCS (Frame Check Sequence) & Even parity
Total cable length| 15 m Max.

Remote I/O port pin arrangement:

The Remote I/O Target type: Hand Reader and Controller I/O Panel

Pin No.

|

Signal name

| Symbol|

Direction

|

Comment

---|---|---|---|---
Hand Reader| Controller I/O Panel
1| Power Supply to Remote I/O

Target

| VCC (DC5V)| ‐‐‐‐|
2| Red or Right Status LED| Red‐LED| Right‐LED| Output|
3| Green or Left Status LED| Green‐LED| Left‐LED| Output|
4| Buzzer or Right‐Button| Buzzer| Right‐Button| Output| Input|
5| Push‐Button or Left‐Button| Push‐Button| Left‐Button| Input|
6| Common Ground| GND| ‐‐‐‐|
7|

Antenna Coil

| Ant coil 1| ‐‐‐‐| ‐‐‐‐|
8| Ant coil 2| ‐‐‐‐| ‐‐‐‐|

1. Hand Reader Operation Brief Description:
2. When the Push‐Button of the Hand Reader was press by operator, the Red‐LED of the Hand Reader is turned on and the Hand Reader begins to access the TIRIS Tag.
3. While Hand Reader is accessing the TIRIS Tag, the Red‐LED is turned on until the CID/data is accessed successfully or failure and the CID/data or message is transmitted to the host system completed or the access time over 1 second or the CID Read/Write controller receives a new command from Host system, the Red‐LED will be turned off.
4. When  the  CID/data  is  accessed  successfully,  the  Green‐LED  is  turned  on.  If  the  CID/data  is  accessed failure or the CID Read/Write controller request ready to send but the Host has no response over 500 ms, the Red‐LED and Buzzer is turned on and off short beep for 3 times.
5. Controller I/O Panel Operation Brief Description:
6. When the Left‐Button or Right‐Button of the Controller I/O panel was press by operator, the Left‐LED and Right‐LED of Controller I/O panel is turned on and the CID Read/Write controller begins to access the TIRIS Tag.
7. When the CID Read/Write controller receives accessing RFID Tag command from the Host system, the Left‐LED and Right‐LED of Controller I/O panel is turned on together and the CID Read/Write controller begins to access the TIRIS Tag.
8. The Left‐LED and Right‐LED status will not change during the CID Read/Write controller is accessing the TIRIS Tag. When the CID/data is accessed successfully and the CID/data is transmitted to the host system  completed  or  the  CID  Read/Write  controller  receives  a  new  command  from  Host  system,  the  Left‐LED and Right‐LED will be turned off. However the feedback time span of the LED turn on should not be less than 1 second.
9. When the CID/data is accessed successfully, the CID Read/Write controller begins to request the Host system for ready to send CID/data, the Left‐LED and Right‐LED is turned on 500 ms and off 500 ms until the CID/data is transmitted to the Host system completed.

RESET Switch specifications

The CID Read/Write controller RESET Switch must be press to reset system when the CID Read/Write controller is crash or other factor to result in system to stop working.

ANTENNA Coil specifications

1. The CID Read/Write controller antenna coil Inductance = 500~520uH @ 134.2KHz and Wire diameter = 0.2 ~ 0.5mm recommended.
2. The antenna is designed for a free air application. When mounting the CID Read/Write controller’s antenna, make sure that the communication surface of antenna head is not below the top surface of sheet metal top panel (mounting bracket). Otherwise, the effective communication distance will decrease.

DIP Switch settings specifications:

6

|

Target address Status

| ON| The Target address in the frame structure field must match the DIP‐SW No.1 to No.5 setting, otherwise controller return an error.

OFF

| The controller accepts any number in the frame structure field when DIP‐SW No.1 to No.5 set to 00, otherwise controller return

an error.

7| Test mode| ON| The controller automatic read tag RFID repeatedly.
OFF| Normal operation.
8| Beeper status| ON| The beeper is enabled when a correct Stream Function executed.
OFF| The beeper is disabled.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>