aoc Q32V3S LCD Monitor User Manual

LCD Monitor
User Manual
Q32V3S

Safety

National Conventions

The following subsections describe notational conventions used in this document.

Notes, Cautions, and Warnings
Throughout this guide, blocks of text may be accompanied by an icon and printed in bold type or in italic type. These blocks are notes, cautions, and warnings, and they are used as follows:

NOTE: A NOTE indicates important information that helps you make better use of your computer system.
CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. WARNING: A  WARNING indicates the potential for bodily harm and tells you how to avoid the problem. Some warnings may appear in alternate formats and may be unaccompanied by an icon. In such cases, the specific presentation of the warning is mandated by regulatory authority.

Power

The monitor should be operated only from the type of power source indicated on the label. If you are not sure of the type of power supplied to your home, consult your dealer or local power company.
The monitor is equipped with a three-pronged grounded plug, a plug with a third (grounding) pin. This plug will fit only into a grounded power outlet as a safety feature. If your outlet does not accommodate the three-wire plug, have an electrician install the correct outlet, or use an adapter to ground the appliance safely. Do not defeat the safety purpose of the grounded plug.
Unplug the unit during a lightning storm or when it will not be used for long periods of time. This will protect the monitor from damage due to power surges.
Do not overload power strips and extension cords. Overloading can result in fire or electric shock.
**** To ensure satisfactory operation, use the monitor only with UL listed computers which have appropriate configured receptacles marked between 100-240V AC, Min. 1.5A.
The wall socket shall be installed near the equipment and shall be easily accessible.

Installation

Do not place the monitor on an unstable cart, stand, tripod, bracket, or table. If the monitor falls, it can injure a person and cause serious damage to this product. Use only a cart, stand, tripod, bracket, or table recommended by the manufacturer or sold with this product. Follow the manufacturer’s instructions when installing the product and use mounting accessories recommended by the manufacturer. A product and cart combination should be moved with care.
Never push any object into the slot on the monitor cabinet. It could damage circuit parts causing a fire or electric shock. Never spill liquids on the monitor.
Do not place the front of the product on the floor.
If you mount the monitor on a wall or shelf, use a mounting kit approved by the manufacturer and follow the kit instructions.
To avoid potential damage, for example the panel peeling from the bezel, ensure that the monitor does not tilt downward by more than -5 degrees. If the -5 degree downward tilt angle maximum is exceeded, the monitor damage will not be covered under warranty.
**** Leave some space around the monitor as shown below. Otherwise, air- circulation may be inadequate hence overheating may cause a fire or damage to the monitor.
See below the recommended ventilation areas around the monitor when the monitor is installed on the wall or on the stand:

Installed with stand

Please purchase a suitable wall mount to avoid the lack of distance between the back signal cable and the wall.

Cleaning

Clean the cabinet regularly with cloth. You can use soft-detergent to wipe out the stain, instead of strong-detergent which will cauterize the product cabinet.
When cleaning, make sure no detergent is leaked into the product. The cleaning cloth should not be too rough as it will scratch the screen surface.
**** Please disconnect the power cord before cleaning the product.

Other

If the product is emitting a strange smell, sound or smoke, disconnect the power plug IMMEDIATELY and contact a Service Center.
Make sure that the ventilating openings are not blocked by a table or curtain.
Do not engage the LCD monitor in severe vibration or high impact conditions during operation.
Do not knock or drop the monitor during operation or transportation.

Setup

Contents in Box

Not all signal cables (DP, HDMI cables) will be provided for all countries and regions. Please check with the local dealer or AOC branch office for confirmation.

Setup Stand & Base

Please setup or remove the base following the steps as below.

Setup:

Remove:

Adjusting Viewing Angle

For optimal viewing it is recommended to look at the full face of the monitor, then adjust the monitor’s angle to your own preference. Hold the stand so you will not topple the monitor when you change the monitor’s angle. You are able to adjust the monitor as below:

NOTE:
Do not touch the LCD screen when you change the angle. It may cause damage or break the LCD screen.

• Display design may differ from those illustrated.
  Warning

  • To avoid potential screen damage, such as panel peeling, ensure that the monitor does no t tilt downward by more than -5 degrees.
  • Do not press the screen while adjusting the angle of the monitor. Grasp only the bezel.

Connecting the Monitor

Cable Connections In Back of Monitor and Computer:

1. Power
2. Earphone
3. DisplayPort
4. HDMI

Connect to PC

1. Connect the power cord to the back of the display firmly.
2. Turn off your computer and unplug its power cable.
3. Connect the display signal cable to the video connector on the back of your computer.
4. Plug the power cord of your computer and your display into a nearby outlet.
5. Turn on your computer and display.

If your monitor displays an image, installation is complete. If it does not display an image, please refer Troubleshooting. To protect equipment, always turn off the PC and LCD monitor before connecting.

Adjusting

Hotkeys

Menu/Enter
When there is no OSD, Press to display the OSD or confirm the selection. Press about 2 second to turn off the monitor.

Power
Press the Power button to turn on the monitor.

Volume/Right
When there is no OSD, Press Volume button to active volume adjustment bar, Press Left or Right to adjust volume.

Source/Exit
When the OSD is closed, press Source/Exit button will be Source hot key function.

Eco /DCR/Down
When there is no OSD, Press this button to enter Eco/DCR adjustment. Then press Left or Right button to choose different Eco/DCR.

Clear Vision

1. When there is no OSD, Press the “Left” button to activate Clear Vision.

2. Use the “Left” or “Right” buttons to select between weak, medium, strong, or off settings. Default setting is always “off”.

3. Press and hold “Left” button for 5 seconds to activate the Clear Vision Demo, and a message of “Clear Vision Demo: on” will be display on the screen for a duration of 5 seconds. Press and hold “Left” button for 5 seconds again, Clear Vision Demo will be off.

Clear Vision function provides the best image viewing experience by converting low resolution and blurry images into clear and vivid images.

Weak
Medium
Strong
Clear Vision Demo| On or Off| Disable or Enable Demo

OSD Setting

Basic and simple instruction on the control keys.

1. Press the MENU-button to activate the OSD window.
2. Press Left or Right to navigate through the functions. Once the desired function is highlighted, press the MENUbutton to activate it, press Left or Right to navigate through the sub-menu functions. Once the desired function is highlighted, press MENU-button to activate it.
3. Press Left or Right to change the settings of the selected function. Press Exit­button to exit. If you want to adjust any other function, repeat steps 2-3.
4. OSD Lock/Unlock Function: To lock or unlock the OSD, press and hold the Down­button for 10s while OSD function is not active.

Notes:

1. If the product has only one signal input, the item of “Input Select” is disable to adjust.
2. ECO modes (except Standard mode), Clear vision, DCR, DCB mode and Picture Boost, for these states that only one state can exist.

Luminance

| Contrast| 0-100| Contrast from Digital-register.
---|---|---|---
Brightness| 0-100| Backlight Adjustment.
Eco mode| Standard| | Standard Mode.
Text| | Text Mode.
Internet| | Internet Mode.
Game| | Game Mode.
Movie| | Movie Mode.
Sports| | Sports Mode.
Reading| | Reading Mode.
Gamma| Gammal| Adjust to Gamma 1.
Gamma2| Adjust to Gamma 2.
Gamma3| Adjust to Gamma 3.
DCR| On| | Enable dynamic contrast ratio.
Off| | Disable dynamic contrast ratio.
HDR Mode| Off| | Select HDR Mode.
HDR Picture|
HDR Movie|
HDR Game|

Note: When “HDR Mode” is set to “non-off”, the items “Contrast”, “Brightness”, “Gamma” cannot be adjusted.

Color Setup

| Color Temp.| Warm| | Recall Warm Color Temperature from EEPROM.
---|---|---|---|---
Normal| | Recall Normal Color Temperature from EEPROM.
Cool| | Recall Cool Color Temperature from EEPROM.
sRGB| | Recall SRGB Color Temperature from EEPROM.
User| | Restore Color Temperature from EEPROM.
DCB Mode| Full Enhance| On or Off| Disable or Enable Full Enhance Mode
Nature Skin| On or Off| Disable or Enable Nature Skin Mode
Green Field| On or Off| Disable or Enable Green Field Mode
Sky-blue| On or Off| Disable or Enable Sky-blue Mode
AutoDetect| On or Off| Disable or Enable AutoDetect Mode
Off| On or Off| Disable or Enable Off Mode
DCB Demo| | On or Off| Disable or Enable Demo
Red| | 0-100| Red gain from Digital-register.
Green| | 0-100| Green gain from Digital-register.
Blue| | 0-100| Blue gain from Digital-register.

Note: When “HDR Mode” under “Luminance” is set to “non-off”, all items under “Color Setup” cannot be adjusted.

Picture Boost

| Bright Frame| on or off| Disable or Enable Bright Frame
---|---|---|---
Frame Size| 14-100| Adjust Frame Size
Brightness| 0-100| Adjust Frame Brightness
Contrast| 0-100| Adjust Frame Contrast
H. position| 0-100| Adjust Frame horizontal Position
V. position| 0-100| Adjust Frame vertical Position

Note: Adjust the brightness, contrast, and position of the Bright Frame for better viewing experience.
When “HDR Mode” under “Luminance” is set to “non-off”, all items under “Picture Boost” cannot be adjusted.

OSD Setup

| Language| | Select the OSD language
---|---|---|---
Timeout| 5-120| Adjust the OSD Timeout
DP Capability
(only for certain models)| 1.1/1.2| If the DP video content supports DP1.2, please select DP1.2 for DP Capability; otherwise, please select DP1.1.
Please be noted that only DP1.2 support
Adaptive-Sync function
H. Position| 0-100| Adjust the horizontal position of OSD
V. Position| 0-100| Adjust the vertical position of OSD
Transparence| 0-100| Adjust the transparence of OSD
Break Reminder| on or off| Break reminder if the user continuously work for more than 1 hrs

Game Setting

| Game Mode| Off| No optimization by Smart image game
---|---|---|---
FPS| For playing FPS (first Person Shooters) games. Improves dark theme black level details.
RTS| For playing RTS (Real Time Strategy). Improves the image quality.
Racing| For playing Racing games. Provides fastest response time and high color saturation.
Gamer 1| Users preference settings saved as Gamer 1.
Gamer 2| User’s preference settings saved as Gamer 2.
Gamer 3| User’s preference settings saved as Gamer 3.
Shadow Control| 0-100| Shadow Control Default is 50. then end-user can adjust from 50 to 100 or 0 to increase contrast for clear picture.
1. If picture is too dark to be saw the detail clearly. adjusting from 50 to100 for clear picture.
2. If picture is too white to be saw the detail clearly. adjusting from 50 too for clear picture
Overdrive
(only for certain models)| Off| Adjust the response time.
Weak
Medium
Strong
Game Color| 0-20| Game Color will provide 0-20 level for adjusting saturation to get better picture.
LowBlue Mode| Reading / Office / Internet / Multimedia / Off| Decrease blue light wave by controlling color temperature.
Dial Point| On or Off| The ‘Dial Point’ function places an aiming indicator in the
center of screen for helping gamers to play First Person Shooter (FPS) games with an accurate and precise aiming.
Adaptive-Sync
(only for certain models)| On or Off| Disable or Enable Adaptive-Sync.
Adaptive-Sync Run Reminder: When the Adaptive-Sync feature is enabled. there may be flashing in some game environments.
Frame Counter (only for certain models)| Off / Right-up / Right-Down / Left- Down / Left-Up| Display V frequency on the corner selected

Note: When “HDR Mode” under “Luminance” is set to “non-off”, the items “Game Mode”, “Shadow Control”, “Game Color” cannot be adjusted.

Extra

| Input Select| | Select Input Signal Source
---|---|---|---
Off timer| 0-24hrs| Select DC off time
Image Ratio| Wide| Select image ratio for display.
4:03
DDC/CI| Yes or No| Turn ON/OFF DDC/CI Support
Reset| Yes or No| Reset the menu to default
(ENERGY STAR’ available for selective models)
ENERGY STAR” or No

Exit

| Exit| |
---|---|---|---

LED Indicator

Troubleshoot

is properly connected to a grounded power outlet and to the monitor.
No images on the screen| • Is the power cord connected properly?
Check the power cord connection and power supply.
• Is the cable connected correctly? (Connected using the I-IDMI cable)
Check the I-IDMI cable connection. (Connected using the DP cable)
Check the DP cable connection.
• HDMI/DP input is not available on every model.
• If the power is on, reboot the computer to see the initial screen (the login screen), which can be seen.
If the initial screen (the login screen) appears, boot the computer in the applicable mode (the safe mode for Windows 7/8/10) and then change the frequency of the video card.
(Refer to the Setting the Optimal Resolution)
If the initial screen (the login screen) does not appear, contact the Service Center or your dealer.
• Can you see “Input Not Supported” on the screen?
You can see this message when the signal from the video card exceeds the maximum resolution and frequency that the monitor can handle properly. Adjust the maximum resolution and frequency that the monitor can handle properly.
• Make sure the AOC Monitor Drivers are installed.
Picture Is Fuzzy & Has Ghosting Shadowing Problem| Adjust the Contrast and Brightness Controls.
Press to auto adjust.
Make sure you are not using an extension cable or switch box. We recommend plugging the monitor directly to the video card output connector on the back.
Picture Bounces, Flickers Or Wave Pattern Appears In The Picture| Move electrical devices that may cause electrical interference as far away from the monitor as possible.
Use the maximum refresh rate your monitor is capable of at the resolution you are using.
Monitor Is Stuck In Active Off- Mode”| The Computer Power Switch should be in the ON position.
The Computer Video Card should be snugly fitted in its slot.
Make sure the monitor’s video cable is properly connected to the computer. Inspect the monitor’s video cable and make sure no pin is bent.
Make sure your computer is operational by hitting the CAPS LOCK key on the keyboard while observing the CAPS LOCK LED. The LED should either turn ON or OFF after hitting the CAPS LOCK key.
Missing one of the primary colors (RED, GREEN, or BLUE)| Inspect the monitor’s video cable and make sure that no pin is damaged. Make sure the monitor’s video cable is properly connected to the computer.
Picture has color defects (white does not look white)| Adjust RGB color or select desired color temperature.
Horizontal or vertical disturbances on the screen| Use Windows 7/8/10 shut-down mode to adjust CLOCK and FOCUS. Press to auto-adjust.
Regulation & Service| Please refer to Regulation & Service Information which is in the CD manual or www.aoc.com (to find the model you purchase in your country and to find Regulation & Service Information in Support page.

Specification

General Specification

Preset Display Modes

STANDARD| RESOLUTION| HORIZONTAL
FREQUENCY(kHz)| VERTICAL
FREQUENCY(Hz)
---|---|---|---
VGA| 640×480@60Hz| 31,469| 59,94
VGA| 640×480@67Hz| 35| 66,667
VGA| 640×480@72Hz| 37,861| 72,809
VGA| 640×480@75Hz| 37,5| 75
DOS MODE| 720×400@70Hz| 31,469| 70,087
DOS MODE| 720×480@60Hz| 29,855| 59,710
SD| 720×576@50Hz| 31,25| 50
SVGA| 800×600@56Hz| 35,156| 56,25
SVGA| 800×600@60Hz| 37,879| 60,317
SVGA| 800×600@72Hz| 48,077| 72,188
SVGA| 800×600@75Hz| 46,875| 75
SVGA| 832×624@75Hz| 49,725| 74,551
XGA| 1024×768@60Hz| 48,363| 60,004
XGA| 1024×768@70Hz| 56,476| 70,069
XGA| 1024×768@75Hz| 60,023| 75,029
XGA| 1024×768@75Hz| 60,241| 74,927
SXGA| 1280×1024@601-Iz| 63,981| 60,02
SXGA| 1280×1024@751-Iz| 79,975| 75,025
Full HD| 1920×1080@601-Iz| 67,5| 60
QHD| 2560×1440@601-Iz| 88,787| 59,951
QHD| 2560×1440@75Hz| 111,028| 74,968

Pin Assignments

Pin No.| Signal Name| Pin No.| Signal Name| Pin No.| Signal Name
---|---|---|---|---|---
1.| TMDS Data 2+| 9.| TMDS Data 0-| 17.| DDC/CEC Ground
2.| TMDS Data 2 Shield| 10.| TMDS Clock +| 18.| +5V Power
3.| TMDS Data 2-| 11.| TMDS Clock Shield| 19.| Hot Plug Detect
4.| TMDS Data 1+| 12.| TMDS Clock-| |
5| TMDS Data 1Shield| 13.| CEC| |
6.| TMDS Data 1-| 14.| Reserved (N.C. on device)| |
7.| TMDS Data 0+| 15.| SCL| |
8.| TMDS Data 0 Shield| 16.| SDA| |

20-Pin Color Display Signal Cable

Plug and Play

Plug & Play DDC2B Feature
This monitor is equipped with VESA DDC2B capabilities according to the VESA DDC STANDARD. It allows the monitor to inform the host system of its identity and, depending on the level of DDC used, communicate additional information about its display capabilities.
The DDC2B is a bi-directional data channel based on the I2C protocol. The host can request EDID information over the DDC2B channel.

www.aoc.com
©2020 AOC. All Rights Reserved.

References

• Homepage | AOC Monitors

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>