PEREL EDB8 Wireless Door Bell User Manual
- June 5, 2024
- PEREL
Table of Contents
PEREL EDB8 Wireless Door Bell
Introduction
To all residents of the European Union Important environmental information about this product.
This symbol on the device or the package indicates that disposal of the device after its lifecycle could harm the environment. Do not dispose of the unit (or batteries) as unsorted municipal waste; it should be taken to a specialized company for recycling. This device should be returned to your distributor or to a local recycling service. Respect the local environmental rules. If in doubt, contact your local waste disposal authorities.
Thank you for choosing Perel! Please read the manual thoroughly before bringing this device into service. If the device was damaged in transit, do not install or use it and0 contact your dealer.
Symbols
- CE marking.
- Read and understand this manual and all safety signs before using this appliance.
- For indoor use only.
- Class II equipment.
Safety Instructions
- This device can be used by children aged from 8 years and above, and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the use of the device in a safe way and understand the hazards involved. Children shall not play with the device. Cleaning and user maintenance shall not be made by children without supervision.
- Do not install the transmitter on a metal surface.
- Keep away from heat sources such as radiators or damp areas such as a kitchen or bathroom.
- Keep away from rain, moisture, splashing and dripping liquids.
- Before drilling any holes in the wall, please make sure there are not cables or pipes that you may accidentally damage.
General Guidelines
- Refer to the Velleman® Service and Quality Warranty on www.velleman.eu.
- Protect this device from shocks and abuse. Avoid brute force when operating the device.
- Familiarise yourself with the functions of the device before actually using it.
- All modifications of the device are forbidden for safety reasons. Damage caused by user modifications to the device is not covered by the warranty.
- Only use the device for its intended purpose. Using the device in an unauthorized way will void the warranty.
- Damage caused by disregard of certain guidelines in this manual is not covered by the warranty and the dealer will not accept responsibility for any ensuing defects or problems.
- Keep this manual for future reference.
Overview
Receiver
- code
- volume
- mode
- mounting hole
- melody
- battery cover
Transmitter
- push button
- mounting holes
- interface
Battery
WARNING: Do not puncture batteries or throw them in fire as they may explode. Do not attempt to recharge non-rechargeable batteries (alkaline). Dispose of batteries in accordance with local regulations. Keep batteries away from children.
- On the receiver, open the battery cover and insert two AA/LR6 batteries (mind the polarity)., and close.
- On the transmitter, remove the mounting plate by gently inserting a flathead screwdriver into the slot.
- Carefully insert a CR2032 battery into the battery holder (mind the polarity).
- Proceed with the mounting prior to re-installing the mounting plate onto the transmitter.
Mounting
Transmitter
- Drill two holes at a required height according to the, indicated positions on the mounting plate.
- Insert a wall plug in each hole and fix the mounting plate with two screws.
- Align the transmitter and the mounting plate, and gently click in place.
- You can also mount the transmitter with double-sided adhesive tape.
Receiver
- Drill two holes (Ø 6 mm) at a required height according to the indicated positions on the mounting plate.
- Insert a wall plug and a screw in each hole.
- Mount the receiver.
- You can also mount the receiver with double-sided adhesive tape.
Buttons
Door Chime
- On the transmitter, press the push button once. The receiver will sound.
- To repeat, just press the button again. Do not hold the button pressed.
Code Button
- The code button is used to pair the receiver with another transmitter (see auto-learning chapter below).
Mode Button
- The mode button is used to select the working mode: sound only, LED only or sound and LED.
Melody Selector
- Press the selector to select the desired melody.
Volume Adjustment
- Increase and decrease the volume level by pressing the volume adjustment button.
Auto-Learning Code
Pairing 1 Transmitter
- After powering both the transmitter and receiver, the receiver will sound to indicate that it is in working status.
- Press the code button on the receiver. The receiver will beep to indicate it has entered the pairing mode.
- Press the push button on the transmitter within 15 seconds to pair. If the button is not pressed within 15 seconds, the receiver will beep twice and exit the pairing status. In this case, repeat as described above.
- To disconnect the receiver from the transmitter, please press and hold the code button for about 3 seconds. The receiver will beep 5 times and unpair.
Pairing Multiple Transmitters
- After powering all the transmitters and receiver, the, receiver will sound to indicate that it is in working status.
- Execute the pairing procedure for every transmitter as described above.
Notes
- After replacing the batteries in the transmitter, you will need to follow the same procedure of the auto-learning code set-up as above.
- If the receiver sounds during the pairing, pairing failed due to interference. In this case, disconnect the receiver from the transmitter and restart pairing.
- A single receiver supports up to four transmitters.
Specifications
- operating distance …………………. ± 300 m (in open field)
- frequency ………………………………………….. 433.92 MHz
- ringing volume ……………………… > 80 dB (within 0.5 m)
- reception sensitivity ……………………………….. < 80 dBm
- transmitting power ………………………………….. 0.12 mW
- transmitting current ……………………………………. 15 mA
quiescent current
- receiver ……………………………………………. < 200 μA
- transmitter …………………………………………… < 5 μA
- digital code ………………………………………. auto learning
- modulation type ……………………………………………. ASK
dimensions
- receiver ……………………………….. 105 x 105 x 30 mm
- transmitter ……………………………… 50 x 50 x 20 mm
- power supply
- receiver ……………………… 2 x 1.5 V AA/LR6 (not incl.)
- transmitter ……. 1 x CR2032, 3 V lithium battery (incl.)
RED Declaration of Conformity
Hereby, Velleman Group nv declares that the radio equipment type EDB8 is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: www.velleman.eu.
Use this device with original accessories only. Velleman Group NV cannot be held responsible in the, the event of damage or injury resulting from (incorrect) use of this device. For more info concerning this product and the latest version of this manual, please visit our website www.velleman.eu. The information in this manual is subject to change without prior notice.
COPYRIGHT NOTICE
The copyright to this manual is owned by Velleman Group nv. All worldwide rights reserved. No part of this manual may be copied, reproduced, translated or reduced to any electronic medium or otherwise without the prior written consent of the copyright holder.
Imported for Perel by Velleman Group nv Legen Heirweg 33, 9890 Gavere, Belgium www.velleman.eu
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>