inventor MP862W Mini Bar Refrigerator User Manual

REFRIGERATOR
**MINI BAR
USER’S MANUAL

MODELS:
MP862W
MP860SEC
MP860S-BS
MP860S
**

Dear Consumer,
Congratulations on your choice!
Inventor Mini Bars, cover multiple needs and demands, not limited only to small student’s apartments but also accommodating hotel rooms.
F Energy class efficiency, low energy consumption, and a modern design are an ideal combination, making Inventor Mini Bars the best choice!
Please refer to this manual of the Mini Bar, through the guidelines included, to benefit from both, energy savings and performance efficiency.

SAFETY & WARNING INSTRUCTIONS

• No children under the age of 8 should be permitted to operate this electric device. Be certain, that children, handicapped people, or people with a lack knowledge
  and experience must be supervised, depending on the situation, by persons responsible for their well-being and do not undertake procedures such as the cleaning or the
  maintenance of this device.

• It is important that adequate supervision is provided and that no minors are left unattended with this device.

• This refrigerator is intended to be used in household and similar residential applications such as:

1. Farmhouses; staff kitchen areas in shops, offices, and other working environments;
2. By clients in hotels, motels bed and breakfast,s and other residential type environments.

• Do not install the appliance in areas that are too humid or too cold, such as during construction appendices, garages or wine cellars.

• This device should always be kept in an upright position to avoid any damage.

• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent, or similarly qualified persons to avoid a hazard. Never attempt to dismantle, repair
  or modify the device.

• Ventilation openings, in both the appliance’s enclosure and in the built-in structure, should be clear of obstructions. Mechanical devices or other means of accelerated
  defrosting should not be used, only methods recommended by the manufacturer should be applied.

• As this device is heavy, always be cautious when relocating, safety gloves are recommended.

• When relocating this appliance, slightly lift from the front, in order to avoid any floor damage.

• Do not attempt to repair, dismantle or modify this appliance. Contact your authorized service technician for repair or maintenance of this device.

• Do not operate this unit by switching the main power supply on or off.

• During operation, do not touch the compressor or the condenser, be cautious as they are hot.

• Do not place heavy objects on the power cord. Make sure that the cord is not compressed.

• Do not place the cord under any obstacles (carpets rugs or runners etc). Cord should be arranged away from areas where accidental tripping may occur.

• Do not operate other electric appliances inside the food storage compartments of this device, unless recommended by the manufacturer.

• Do not store explosive substances such as aerosol cans with a flammable propellant in this appliance.

• The refrigerant circuit should remain intact. If damage occurs, be extremely cautious of any flames or sources of ignition. Ventilate the room.

• Do not sit or climb on the device.

• Do not place the unit in direct sunlight or near other heating sources like radiators, cookers, ovens, or hobs.

• Do not use the unit near heat sources, chemicals, radiators, flammable materials, or fire.

ELECTRICAL INFORMATION

• The nameplate, with all the electrical and technical data of this appliance, is located on the rear panel.

• The appliance should be installed in accordance with national wiring regulations.

• Be sure the device is grounded properly. Proper grounding is important as it minimizes the chance of electric shock or fire. The power cord is equipped with a grounding plug for protection against electric shock hazards.

• The device must be used in a properly grounded wall socket. If the specific socket you intend to use is not adequately grounded or protected by a time-delay fuse or
  circuit breaker, have a qualified electrician install the proper receptacle.

• Ensure the wall socket is still accessible after the installation of the refrigerator.

• Do not use extension cords or adapter plugs with this device.

• Make sure not to cause damage to the electrical components (e.g. main plug, main cable, compressor). Contact the Service or an electrician to change the electrical
  components.

• To avoid personal injury, always disconnect the power supply of the device, before maintenance.

Power off the refrigerator before removing the plug. Do not disconnect the plug from the wall socket by pulling on the cord.

SOCIABLE REMARKS ON ENVIRONMENTAL PROTECTION

Disposal of equipment no longer used:
Please follow the instructions below, when using this refrigerator in European countries.

• This appliance requires special treatment for disposal. In the European Union, electronic equipment must not be treated as domestic waste but must be disposed of
  professionally in accordance with Directive 2002/96/EC of the European Parliament and Council of 27th January 2003 concerning old electrical and electronic equipment. The disposal of this unit should follow all legal requirements and should not be disposed of as unsorted municipal waste.
  The hazardous substances can leak into the groundwater supply thus entering the food chain, endangering your health and the environment.

• There are several alternative solutions for disposal. Please remove all doors before disposal to prevent children’s accidental trapping.
  ****A) Your local municipality has established free collection systems for electronic waste.
  B) Your local retailer upon purchase of a new product.
  C) The manufacturer may accept the old appliance for disposal.
  D) Old appliances sometimes contain valuable resources for scrap metal dealers.

• For EN standard: This appliance can be used by children aged 8 years and above and persons with reduced physical sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision. Children aged from 3 to 8 years are allowed to load and unload refrigerating appliances.

• To avoid contamination of food, please respect the following instructions:
  – Opening the door for long periods can cause a significant increase in the temperature in the compartments of the appliance.
  – Clean regular surfaces that can come in contact with food and accessible drainage system.
  – Clean water tanks if they have not been used for 48 h; flush the water system connected to a water supply if water has not been drawn for 5 days. (note 1)
  – Store raw meat and fish in suitable containers in the refrigerator, so that it is not in contact with or drip onto other food.
  – Two-star frozen-food compartments are suitable for storing pre-frozen food, storing or making ice cream, and making ice cubes. (note 2)
  – One-, two- and three-star compartments are not suitable for the freezing of fresh food. (note 3)
  – For appliances without a 4-star compartment: this refrigerating appliance is not suitable for freezing foodstuffs.(note 4)
  – If the refrigerating appliance is left empty for long periods, switch off, defrost, clean, dry, and leave the door open to prevent mold from developing within the appliance.

• Note 1,2,3,4: Please confirm whether it is applicable according to your product compartment type. l For a freestanding appliance: this refrigerating appliance is not intended to be used as a built-in appliance.

STEPS BEFORE USE

Please refer to the electronic warranty instructions, in the last page (English section) of this manual.

For warranty purposes, please note the SN (serial number). The SN is labeled opposite the device.

GETTING TO KNOW YOUR MINI BAR

1. Thermostat
2. Defrosting Pan
3. Interior Light
4. Shelf
5. Bucket
6. Door Compartments
7. Bottle Rack
8. Reversible Door
9. Adjustable Foot
10. Power Cord

MINI BAR FEATURES

Place the appliance in a location where the ambient temperature corresponds to the climate classification for which it is designed. You can find the climate classification on the nameplate. The following table shows the climate classification and its matching ambient temperature:

Table 1 Climate classes

Extended temperate: ‘this refrigerating appliance is intended to be used at ambient temperatures ranging from 10°C to 32°C
Temperate: ‘this refrigerating appliance is intended to be used at ambient temperatures ranging from 16°C to 32°C
Subtropical: ‘ this refrigerating appliance is intended to be used at ambient temperatures ranging from 16 °C to 38 °C
Tropical: ‘ this refrigerating appliance is intended to be used at ambient temperatures ranging from 16°C to 43°C

Interior Dimensions (mm)

*There might be a deviation regarding the above prices. Kindly refer to the purchased product.

INSTALLATION GUIDELINES

Position
Upon the positioning of this unit, keep in mind the floor must be flat and sturdy and the room should be well ventilated, without additional heating sources nearby.

1. Allow sufficient air ventilation surrounding the unit. The rear end (backside) of this appliance should stand against a wall allowing sufficient air ventilation as follows:
   ➟ 10cm from the top
   ➟ 10cm from the back
   ➟ 10cm from the rest sides
   

2. Wait at least 4 hours before connecting the appliance to the power supply, thus, allowing all fluids to settle in the compressor.
   

3. Upon initial use, operate continuously for 24 hours, thus ensuring the correct temperature is reached and smooth operation of the unit is achieved.
   

Reversible Door
The door opening can change from either the left or the right side, according to what is best suited for its location. Ensure there is enough adequate space for the door to open fully. To change the door opening direction, please follow the mentioned below instructions:

Required tools:
Head Screwdriver / Slot head Screwdriver / Hexagonal Spanner

• Before reversing the door swing, unplug the appliance from the power supply and remove goods from fridge.

1. Adjust the leveling foot to its highest position. Tilt the unit slightly backward to take the door off. Rest the unit on something solid so that it will not slip during the door reversing process.
   Do not lay the unit flat as this may damage the coolant system.

2. Remove the plastic cover located on the top right or left (depending on the initial door installation side) of the door hinge, and unscrew the two screws with the stabilizing pin.
   

3. Slightly tilt so that you may have access to the front bottom bracket. Unscrew the two screws located on the bottom left or right (depending on the initial door installation side)and remove the foot from the opposite side. Once the top and bottom screws and also the opposite foot is removed, the door will be completely released.
   

4. Remove the three plastic caps from the side, you are going to install the door and place them on the side where the door was originally installed, in order to cover the three
   screw holes.
   

5. Place the door on the desired side making sure it is in its upright position. Screw the top two screws of the door hinge. Slightly tilt, for better positioning, screw the bottom hinge into place, and also screw the removed foot on the other side. Once completed clip on the top plastic cap.
   

6. Check if door is aligned horizontally and vertically and that the door when shut is completely sealed from all sides.
   

7. Finally tighten the bottom hinge and re-adjust the foot on the opposite side for correct leveling.

Leveling the Unit
Adjust the levelling foot at the front of the unit. If the unit is not aligned, the door and magnetic seal alignments will not be covered properly.

SETTINGS

Thermorstat Temperature Setting
The thermostat is located in the interior at the upper part of the refrigerator. The thermostat setting levels are the following:

• Setting “OFF”: the cooling operation stops
• Setting “MIN”: Minimum cooling It is suggested when the storage quantity is very small.
• Setting “MED”: Normal cooling When installing the appliance for the first time, be sure to set the thermostat to the MED setting and wait for 24hours before placing items inside.
• Setting “MAX”: Maximum cooling If there is a large number of frozen goods, or if the outside temperature is high, the thermostat knob may be set to its highest position, for a short time.

For determining the correct temperature control setting, consider the following:

✓ Room temperature
✓ How frequently does the Mini Bar door open
✓ The quantity of stored goods
✓ Position of the appliance

MAINTENANCE & CLEANING

Prior to cleaning the appliance, unplug from the wall power socket, and remove all shelves.

• Clean the appliance with a moist soft cloth. Use only neutral detergents.
• Clean the unit’s interior with a weak bicarbonate soda solution and rinse with warm water by applying a damp sponge or cloth.
• Use a damp cloth to clean the exterior, keep in mind the door must be shut to avoid getting any polish on the magnetic door seal or the interior of the unit.
• Upon cleaning, rinse the interior with clean water and dry.

• Allow the appliance to dry for approximately 1 to 2 hours.
• Set thermostat to middle position. Plug into a power source. The appliance will chill continuously until the set temperature has been reached.
• Frequently the air vents and the condenser must be cleaned located at the rear end of the appliance, using a vacuum cleaner or a brush. The condenser should always be clean, and free of dust or any other impurities.

• Do not use abrasive products, abrasive cleaning pads, solvents or metal objects. Do not use water spray and steam to clean the appliance.
• Do not use extreme moist cleaning pads. Any moisture around the electric components should be avoided.
• The use of a steam cleaner is prohibited, as this may be very dangerous.

Defrosting

It is recommended to defrost the chill box when 3-4mm frost has been accumulated. To implement the defrosting process, consider the following steps:

1. Unplug the appliance.
2. Empty the appliance.
3. Keep the door open while the defrosting process is in progress.
4. Make sure that the interior is free of frost and clean the chill box with a soft cloth.
5. Re-plug, allow the appliance to operate for approximately 4 hours, then refill.

• Never use sharp or metal objects to remove frost while defrosting
• Do not use any mechanical devices or instruments to accelerate the defrosting process without consulting the manufacturer firs

Interior Light
Thanks to the interior lighting you can have a better insight into your product storage. In the event of a malfunction, you can change the interior light bulb of the refrigerator by yourself, following the below steps:

• pull the plug from the socket
• remove the cover from the lighting
• check if the bulb is fully screwed in
• replace it with a bulb of the same type
• replace the cover
• put the plug into the socket

STORAGE

When appliance is inactive for an extended period of time, please make sure you follow the instructions below, for the appropriate storage of your appliance:

• Turn the unit off allowing one day before storage.
• Remove all the items from the interior compartment.
• Clean the removable parts of the device.
• Leave the door open to prevent unpleasant odors.
• Cover the device.
• Store the refrigerator in an upright position, in a dry, well-ventilated area, and avoid direct sunlight.

TIPS

✓ Do not place products too close. Ensure a sufficient distance for optimum air circulation in the refrigerator.
✓ Avoid extensive use of the door in wet and hot weather, keep in mind, that once the door is opened to shut the soonest possible.
✓ Do not place goods in direct contact with the wall of the refrigerator, always allow some space.
✓ Never place inside the unit, hot or even warm goods without allowing them to chill first.
✓ Be certain the wall behind the appliance is dirt and dust free, especially with outer condenser equipped units.
✓ Do not place goods that are not sealed or well packed directly under the chill box.

TROUBLESHOOTING

socket.
Lighting is not operating| Lamp defective. Replace the bulb as it is suggested on the section “MAINTENANCE & CLEANING”.
Temperature in the refrigerator is too high or too low| Thermostat has been set incorrectly. Set the thermostat correctly.
Condensation appears on the outside surface of the
unit| This may be caused by a change in the room’s temperature. Use a soft cloth to wipe away any condensation. If the problem remains, contact a certified technician for assistance.
Appliance is making a noise| 1) The refrigerant liquid causes noises in the cooling system.
2) Noise is produced while the compressor is operating,
as refrigerant fluid is being pumped within the unit.
3) Make sure the refrigerator is leveled and balanced.
4) Goods have been placed incorrectly in the refrigerator. Place the goods correctly in the refrigerator.
5) Check if the refrigerator’s components are in the proper position.
Odor| 1) Goods are not stored in sealed containers
2) There are spoiled goods inside
3) The interior needs to be cleaned
The refrigerator door  can’t be properly closed| Make sure items are not blocking the door.
Make sure the refrigerator is not overfilled.
Make sure the refrigerator is not tilted.
Long term operation of the compressor| It is normal if the compressor runs for a long time during high ambient temperatures.
Avoid overfilling.
Allow warm and hot goods to chill prior to placing them in the unit.
Avoid the frequent opening of the door.
There is ice all around the chill box| Follow the “defrosting process” mentioned on Section 9.

The ordered parts in the following table can be acquired from the channel of Inventor:

Ordered Part| Provided by| Minimum Time Required for
Provision
---|---|---
Thermostats| Professional maintenance personnel| At least 7 years after the last model is launched on the market
Temperature sensors| Professional maintenance personnel| At least 7 years after the last model is launched on the market
Printed circuit boards| Professional maintenance personnel| At least 7 years after the last model is launched on the market
Light sources| Professional maintenance personnel| At least 7 years after the last model is launched on the market
Door handles| Professional repairers and final users| At least 7 years after the last model is launched on the market
Door hinges| Professional repairers and final users| At least 7 years after the last model is launched on the market
Trays| Professional repairers and final users| At least 7 years after the last model is launched on the market
Baskets| Professional repairers and final users| At least 7 years after the last model is launched on the market
Door gaskets| Professional repairers and final users| At least 7 years after the last model is launched on the market

All the pictures in the manual are for explanatory purposes only. The actual shape of the unit you purchased may be slightly different, but the operations and functions are the same. The company may not be held responsible for any misprinted information. The design and the specifications of the product for reasons, such as product improvement, are subject to change without any prior notice.
Please consult with the manufacturer at +30 211 300 3300 or with the Sales agency for further details. Any future updates to the manual will be uploaded to the service website,
and it is advised to always check for the latest version.

https://www.inventorappliances.com/manuals

Scan here to download the latest version of this manual.
www.inventorappliances.com/manuals

Activate your Warranty
Follow the next quick steps to activate your warranty:
STEP 1
Visit our website via the link:
https://www.inventorairconditioner.com/warranty-inventor

or by scanning the QR code, as follows:

https://www.inventorairconditioner.com/warranty-inventor

STEP 2
Fill in the obligatory fields as requested in the “Owner’s details” and “Unit’s details”:

STEP 3
Click SEND button at the end of the submission form:

STEP 4
Wait for the confirmation email you will receive at the email address you have filled in – please also check your spam folder.
STEP 5
Inventor warranty is now valid!
NOTES

REFRIGERATOR
MINI BAR

V:1.0.042021
Manufacturer: INVENTOR A.G. S.A.
24th km National Road Athens – Lamia & 2 Thoukididou Str., Ag.Stefanos, 14565
Tel.: +30 211 300 3300, Fax: +30 211 300 3333 – www.inventor.ac

References

• Inventor

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>