Philips PH802 Wireless Bluetooth Over-Ear Headphones Noise Isolation Stereo-Complete Features/Instruction Guide

: June 5, 2024
: Philips

phillipsd

Philips PH802 Wireless Bluetooth Over-Ear Headphones Noise Isolation

Stereo

Philips-=PH802-Wireless-Bluetooth-Over-Ear-Headphones-Noise-Isolation-
Stereo-imgg

Specifications

Product Dimensions
1.06 x 6.14 x 8.15 inches
Item Weight
9.2 ounces
Batteries
1 Lithium Polymer batteries
Connectivity Technology
Wireless
Form Factor
Over-Ear
Music time
30 hours
Talk time
30 hours
Standby time
160 hours
Charging time
2 hours
Rechargeable lithium polymer

battery (680 mAh)

Bluetooth version
4.2
Supported audio codec
SBC
Frequency range
2.402-2.480 GHz
Transmitter power
< 10 dBm
Operating range
Up to 10 meters (33 feet)
Brand
Philips Audio

Introduction

Wherever your week takes you, these Wireless Over-Ear Headphones will make your commute more enjoyable with balanced, detailed sound and up to 30 hours of playtime if you need it. Quick charging gives you an extra 2 to 6 hours of battery life.

Important safety instructions

Hearing Safety

Danger
To avoid hearing damage, limit the time you use headphones at high volume and set the volume to a safe level. The louder the volume, the shorter the safe listening time is.

Be sure to observe the following guidelines when using your headset.

Listen at reasonable volumes for reasonable periods of time.
Be careful not to adjust the volume continuously upwards as your hearing adapts.
Do not turn up the volume so high that you can’t hear what’s around you.
You should use caution or temporarily discontinue use in potentially hazardous situations.
Excessive sound pressure from earphones and headphones can cause hearing loss.
Using headphones with both ears covered while driving is not recommended and may be illegal in some areas while driving.
For your safety, avoid distractions from music or phone calls while in traffic or other potentially dangerous environments.

General information

To avoid damage or malfunction:

Caution

Do not expose headphones to excessive heat
Do not drop your headphones.
Headphones shall not be exposed to dripping or splashing.
Do not allow your headphones to be submerged in water.
Do not use any cleaning agents containing alcohol, ammonia, benzene, or abrasives.
If cleaning is required use a soft doth, if necessary dampened with a minimum amount of water or diluted mild soap, to clean the product.
The integrated battery shall not be exposed to excessive heat such as sunshine, fire or the like.
Danger of explosion if the battery is incorrectly replaced. Replace only with the same or equivalent type.

About operating and storage temperatures and humidity

Operate or store in a place where the temperature is between -15°C (5°F) and 55°C (131 °F) (up to 90%relative humidity.
Battery life may be shorter in high or low-temperature conditions.

Your Bluetooth over-ear headphones

Congratulations on your purchase, and welcome to Philips! To fully benefit from the support that Philips offers, register your product at www.philips.com/welcome.
With these Philips over-ear headphones, you can:

enjoy convenient wireless handsfree calls;
enjoy and control wireless music;
switch between calls and music.

What’s in the box

Philips Bluetooth over-ear headphones Philips TAPH802
Audio cable
USB charging cable (for charging only)
Quick start guide

Other devices

A mobile phone or device (e.g. notebook, PAD, Bluetooth adapters, MP3 players, etc) which supports Bluetooth and is compatible with the headset (see ‘Technical data’ on page 8).

Overview of your Bluetooth wireless headset

Audio jack
Microphone
LED indicator
(Power on / off / Pairing)
Micro charging slot

Get started

Charge the battery

Note

Before you use your headset for the first time, place the headset in the charging case and charge the battery for 3 hours for optimum battery capacity and lifetime.
Use only the original USB charging cable to avoid any damage.
Finish your call before charging the headset, as connecting the headset for charging will power the headset off.

Charging case

Connect the supplied USB charging cable to:

The micro USB charging slot on the headphones and
The charger/USB port of a computer.
LED turns red during charging and turns off when the headphones in fully charged.

Tip
Normally, a full charge takes 2 hours.

Pair the headphones with your mobile phone
Before you use the headphones with your mobile phone for the first time, pair it with a mobile phone. A successful pairing establishes a unique encrypted link between the headphones and the mobile phone. The headphones store the last 8 devices in the memory. If you try to pair more than 8 devices, the earliest paired device is replaced by the new one.

Make sure that the headphones are fully charged and turned off.
Press and hold for 5 seconds until the blue and red LED flashes alternately.
The headphone remains in pairing mode for 2 minutes.
Make sure that the mobile phone is turned on and its Bluetooth feature is activated.
Pair the headphones with the mobile phone. For detailed information, refer to the user manual of your mobile phone.

The following example shows you how to pair the headphones with your mobile phone.

Activate the Bluetooth feature of your mobile phone, select Philips PH802

Use your headset

Connect the headset to your Bluetooth device

Turn on your mobile phone/ Bluetooth device.
Press and hold the on/off button to turn the headphones on.
The blue LED will turn on 3s.
The headphones are connected to the last connected mobile phone/ Bluetooth device automatically.

Tip
If you turn on the mobile phone/Bluetooth device or activate the Bluetooth feature after turning on the headphones, you have to reconnect the headphones and mobile phone/ Bluetooth device manually.

Note

**** If the headphones fail to connect to the last connected Bluetooth device within range in 2 minutes, it will change to pairing mode, then will switch off automatically if it’s still not connected to any Bluetooth device 8 minutes later.
If the headphone has no connection history and doesn’t connect to any Bluetooth device within 2 minutes, it will switch off automatically.

Wired Connection

You can also use the headphones with the audio cable provided. Connect the supplied audio cable to the headphones and external audio device.

Tip

The function keys will be disabled when using line-in mode.

Manage your calls and music

On/off

Music control

Other headphones indicator status

Philips-=PH802-Wireless-Bluetooth-Over-Ear-Headphones-Noise-Isolation-
Stereo-fig-8

Notice

Declaration of conformity
Hereby, MMD Hong Kong Holding Limited declares that this product is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. You can find the Declaration of Conformity on www.p4c.philips.com

Disposal of your old product and battery

Your product is designed and manufactured with high quality materials and components, which can be recycled and reused.

This symbol on a product means that the product is covered by European Directive 2012/19/EU.
This symbol means that the product contains a built-in rechargeable battery covered by European Directive
2013/56/EU which cannot be disposed of with normal household waste. We strongly advise you to take your product to an official collection point or a Philips service center to have a professional remove the rechargeable battery. Inform yourself about the local separate collection system for electrical and electronic products and rechargeable batteries. Follow local rules and never dispose of the product and rechargeable batteries with normal household waste. Correct disposal of old products and rechargeable batteries helps prevent negative consequences for the environment and human health.

Remove the integrated battery
If there is no collection/recycling system for electronic products in your country, you can protect the environment by removing and recycling the battery before disposing of the headphones.

Make sure the headset is disconnected from the charging case before removing the battery.

Compliance with EMF
This product complies with all applicable standards and regulations regarding exposure to electromagnetic fields.

Environmental information
All unnecessary packaging has been omitted. We have tried to make the packaging easy to separate into three materials: cardboard (box), polystyrene foam (buffer) and polyethylene (bags, protective foam sheet.) Your system consists of materials that can be recycled and reused if disassembled by a specialized company. Please observe the local regulations regarding the disposal of packaging materials, exhausted batteries, and old equipment.

Notice of compliance
The device complies with the FCC rules, Part 15. Operation is subject to the following two conditions:

This device may not cause harmful interference, and
This device must accept any interference received, including interference that may cause undesired operation.

FCC rules
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protec-tion against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between equipment and receiver
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Canada:
This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science, and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation of the device.
CAN ICES-3(B)/NMB-3(B)

IC Radiation Exposure Statement
This equipment complies with Canada’s radiation exposure limits set forth for uncontrolled environments. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Trademarks

Bluetooth
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by MMD Hong Kong Holding Limited is under license. Other trade-marks and trade names are those of their respective owners.

Siri
Siri is a trademark of Apple Inc., registered in the U.S. and other countries.

Frequently Asked Questions

My Bluetooth headset does not turn on
The battery level is low. Charge the headset.
I cannot pair my Bluetooth headset with my Bluetooth device?
The Bluetooth is disabled. Enable the Bluetooth feature on your Bluetooth device and turn on the Bluetooth device before you turn on the headset.
How to reset pairing?
Let headphones stay in pairing mode (red and blue lights flash alternately), push the power button up to + and hold more than 10 seconds until purple LED light on.
I hear but cannot control music on my Bluetooth device (e.g. play/pause/skip forward/backward)?
Make sure the Bluetooth audio source supports AVRCP (see ‘Technical data’ on page 10).
The volume level of the headset is too low?
Some Bluetooth devices cannot link the volume level with the headset through volume sync. In this case, you have to adjust the volume on your Bluetooth device independently to achieve an appropriate volume level.
The Bluetooth device cannot find the headset?
The headset may be connected to a previously paired device. Turn off the connected device or move it out of range.
Pairing may have been reset or the headset has been previously paired with another device. Pair the headset with the Bluetooth device again as described in the user manual. (see
‘Pair the headset with your Bluetooth device at the first time on page 6).
My Bluetooth headset is connected to a Bluetooth stereo-enabled mobile phone, but music only plays on the mobile phone speaker?
Refer to the user manual of your mobile phone. Select to listen to music through the headset.
The audio quality is poor and crackling noise can be heard?
The Bluetooth device is out of range. Reduce the distance between your headset and Bluetooth device, or remove obstacles between them.
Charge your headset.
The audio quality is poor when streaming from the mobile phone is very slow, or audio streaming does not work at all?
Make sure your mobile phone not only supports (mono) HFP but also supports A2DP and is BT4.0x (or higher) compatible (see ‘Technical data’ on page 8).
does it come with a case?
No case.
What is the max distance they receive sound from the device it’s paired to?
It stays connected about 20 meters but less than 10 meters with obstacles (concrete walls) in the way.
Will these work with video conferencing on my PC?
Yes.
Does it come with a wired connection?
Yes. The cord length is 1.2 meters.
Are this 4.2 Bluetooth?
Yes, it says Bluetooth 4.2 on the box.
Does it have a surround sound effect?
Yes, it has stereo surround sound.
Does the microphone work on these with a Bluetooth receiver? These don’t work for my intended purpose, and I may return.
Yes