Homewell HMW-ARP2000 Pond Pump Instruction Manual
- June 12, 2024
- Homewell
Table of Contents
Homewell HMW-ARP2000 Pond Pump
Product Information
- Brand: Homewell
- Model: HMW-ARP2000, HMW-ARP2500, HMW-ARP3000, HMW-ARP3500, HMW-ARP5000, HMW-ARP6000, HMW-ARP6500, HMW-ARP7000, HMW-ARP8000
- Product Name: Homewell GHP Pond Pump
- Website: www.homewellproducts.com
Product Usage Instructions
Please read the following instructions before using the Homewell GHP Pond
Pump
Safety Precautions
- Ensure to read all directions in the instruction manual before using the product.
- Retain the instruction manual for future reference.
- The pump is to be supplied through a residual current device (RCD) with a rated residual operating current not exceeding 30mA. The pump should be connected grounded properly.
- Do not operate any appliance with a damaged cord or plug, or in abnormal state.
- Do not immerse the plug into water or any other liquids.
- In the following cases, please unplug the pump power plug
- when the water pump is not in use;
- when installing or disassembling components;
- before cleaning the water pump;
- when doing any work for a waterfall or pond.
- Maximum water temperature is 35℃ (95℉). Maximum water depth is 2 meters.
- For safety reasons, any repair work should be done only by the manufacturer of the products or the authorized service facility or discard it.
- Do not lift the pump by holding the power cord to avoid the cable connection off inside of the pump.
- Avoid the pump dry working.
- Do not allow children or the inexperienced to operate and play the product alone without safety supervision.
Structure Breakdown
Follow the steps below for assembly
- Put the rotor with the impeller into the pump body.
- Put on the sealing ring.
- Install the pump chamber.
- Tighten the screws.
- Install the pre-filter.
- Finally, install the rear cover and suction foot.
Pump Features
- Ideal for water gardens, koi ponds, and waterfalls.
- Designed for continuous running operation.
- High-quality ceramic shaft and SIC bearing for long and efficient pump life.
- No oil inside, safe for ponds with fish.
- Thermal overload protection.
- Filters particles above 6mm diameters.
- Simple maintenance with removable impeller.
- Works with Jebao electronic flow controller FC-300A or with Smart WiFi controller MFC300A (Optional).
Specification Parameters
Model| Rated voltage| Flow (GPH)| Max. Total Head (Ft)| Input Current (A)|
Inlet/Outlet (inch)
---|---|---|---|---|---
HMW-ARP2000| 120V 60Hz| 2100| 15| 0.95| 1.5/1.5
HMW-ARP2500| 120V 60Hz| 2500| 16| 1.2| 1.5/1.5
HMW-ARP3000| 120V 60Hz| 3000| 22| 1.6| 1.5/1.5
HMW-ARP3500| 120V 60Hz| 3500| 24| 2.3| 1.5/1.5
HMW-ARP5000| 120V 60Hz| 5000| 21| 2.45| 2/2
HMW-ARP6000| 120V 60Hz| 6000| 26| 2.95| 2/2
HMW-ARP6500| 120V 60Hz| 6600| 24| 3.55| 2/2
HMW-ARP7000| 120V 60Hz| 7200| 26| 4.5| 2/2
HMW-ARP8000| 120V 60Hz| 8000| 28| 5.2| 2/2
Warm tips
-
Submersible Pump:
- The pump needs to be completely immersed in water.
- The diving depth needs to exceed 15 cm (6 feet) of water level to prevent inhalation of air.
-
Non-Submersible Pump:
- Place the pump next to the pool below the water surface.
- Remove the front net.
- Connect the water pipe.
- Use the height difference between the water surface and the pump to fill the pump with water.
-
The water temperature should not exceed 35℃ (95℉) and do not let the pump
freeze in the wintertime -
The electrical connection should be placed in a water-proof area and should be at least 2 meters (6 feet) away from the edge of the pond.
-
Please keep the water clean to prolong the life of the pump.
-
Keep the electrical connections dry! Ensure that the electrical cord loops below the electrical outlet to form a “Drip Loop”. This will prevent water from running down the cord into the electrical outlet.
-
The pump has a built-in thermal overload device which prevents the pump from overheating. The pump must be allowed to cool down before restarting.
Maintenance
- Clean the pump regularly to ensure performance.
- When cleaning the blockage in the pump body, disconnect the power supply first and then disassemble it correctly according to the steps.
- Use a soft cloth to clean the impeller and clean the pump with clear water.
- Remove the pump inlet to access the impeller. Turn around the rotor to check if it is broken or jammed.
- Check the pump inlet, outlet, and connecting pipe for blockages.
Troubleshooting
| Problems | Reasons | Solutions |
|---|
The water pump doesn’t work
| 1.The power is not on; 2.Rotor stuck;
3.Pump overheating.
| 1. Turn on electricity;
2. Clean the rotor;
3. Wait for the water pump to cool down completely.
The flow rate is weakened or other abnormal phenomena
appears
| 1. impeller damaged;
2. The bottom basket filter part of the pump is out of the water.
| ****
1.Replace the impeller with a new one; 2.Put the pump bottom basket filter submersible under he water completely.
Water pump idles
| ****
1. The outlet pipe is too long or blocked;
2. There is residual air in the impeller chamber.
| 1. Cut the outlet pipe shorter or remove blockage;
2. Keep the water pump in water, and continue to turn on and off the power supply for 2 to 3 times to remove the residual air in
the impeller chamber.
DISPOSAL
Please don’t dispose this product as unsorted municipal waste. Collection
of such waste separately for special treatment is necessary. Not put it
together with the domestic waste which should be solved as an authorized place
for recycling of electrical and electronic appliances for collecting and
recycling waste. Please consult with your local seller, to make sure the
product is disposed in an environmental and healthy way.
WARRANTY
- This item covers 1 YEAR LIMITED WARRANTY from the original date of purchase.
- This warranty only applies to the original consumer purchaser and only to products used in normal use and service.
- This warranty does not apply to products that are found to have been improperly installed ,set-up,or used in any way not in accordance with the instruction supplied with product and failure of product’s as a result of an accidents, misuse, abuse, negligence, alternation, or faulty installation.
- This warranty shall not apply to the finish/scratching/tearing on any portion of the product, such as surface and/or weathering,as this is considered normal wear and tear.
- If you have any questions, please visit our website and contact our customer service. www.homewellproducts.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>