HQ POWER VDLLTC Series Plug and Play LED Tube User Manual

HQ POWER VDLLTC Series Plug and Play LED Tube

Introduction

To all residents of the European Union
Important environmental information about this product

This symbol on the device or the package indicates that disposal of the device after its lifecycle could harm the environment. Do not dispose of the unit (or batteries) as unsorted municipal waste; it should be taken to a specialized company for recycling. This device should be returned to your distributor or to a local recycling service. Respect the local environmental rules.

If in doubt, contact your local waste disposal authorities.
Thank you for choosing HQPOWER! Please read the manual thoroughly before bringing this device into service. If the device was damaged in transit, don’t install or use it and contact your dealer. The VDLLTC LED tube is a plug & play tube with 144 ultra-bright LEDs for use in shops, bars, clubs, stages…

Safety Instructions

1. Be very careful during the installation: touching live wires can cause life-threatening electroshocks.
2. Do not touch the device during operation as the housing heats up.
3. Keep this device away from rain and moisture.
4. Unplug the mains lead before opening the housing.

• Damage caused by disregard of certain guidelines in this manual is not covered by the warranty and the dealer will not accept responsibility for any ensuing defects or problems.
• A qualified technician should install and service this device.
• Do not switch the device on immediately after it has been exposed to changes in temperature. Protect the device against damage by leaving it switched off until it has reached room temperature.
• This device falls under protection class I. It is therefore essential that the device be earthed. Have a qualified person carry out the electric connection.
• Make sure that the available voltage does not exceed the voltage stated in the specifications of this manual.
• Do not crimp the power cord and protect it against damage. Have an authorised dealer replace it if necessary.
• Disconnect the device from the mains to clean it or when it is not in use. Handle the power cord by the plug only.
• Do not look directly at the light source as sensitive people may go into epileptic seizure if they do.
• Keep the device away from splashing and dripping liquids. Never put objects filled with liquid on top of the device.
•  The LEDs and mechanical wear are not covered by warranty.
• Note that damage caused by user modifications to the device is not covered by the warranty.
• Keep the device away from children and unauthorised users.

General Guidelines

• This device is designed for professional use on stage, in discos, theatres, etc. The VDLLTC should only be used indoors with an alternating current of max. 230VAC/50Hz.
• Lighting effects are not designed for permanent operation: regular operation breaks will prolong their lives.
• Do not shake the device. Avoid brute force when installing or operating the device.
• Select a location where the device is protected against extreme heat (see “Technical Specifications”), dust and moisture. Respect a minimum distance of 0.5m between the device’s light output and any illuminated surface.
• Use an appropriate safety cable to fix the device (e.g. VDLSC7 or VDLSC8).
• Familiarise yourself with the functions of the device before actually using it. Do not allow operation by unqualified people. Any damage that may occur will most probably be due to unprofessional use of the device.
• Use the original packaging if the device is to be transported.
• All modifications of the device are forbidden for safety reasons.
• Only use the device for its intended purpose. All other uses may lead to short circuits, burns, electroshocks, crash, etc. Using the device in an unauthorised way will void the warranty.

Installation

• Have the device installed by a qualified person, respecting EN 60598-2-17 and all other applicable norms.
• The carrying construction must be able to support 10 times the weight of the device for 1 hour without deforming.
• The installation must always be secured with a secondary attachment e.g. a safety cable.
• Never stand directly below the device when it is being mounted, removed or serviced. Have a qualified technician check the device once a year and once before you bring it into service.
• Install the device in a location with few passers-by that is inaccessible to unauthorised persons.
• Overhead mounting requires extensive experience: calculating workload limits, determining the installation material to be used… Have the material and the device itself checked regularly. Do not attempt to install the device yourself if you lack these qualifications as improper installation may result in injuries.
• Adjust the desired inclination angle via the mounting bracket and tighten the bracket screws.
• Make sure there is no flammable material within a 0.5m radius of the device.
• Have a qualified electrician carry out the electric connection.
• Connect the device to the mains with the power plug. Do not connect it to a dimming pack.
• The installation has to be approved by an expert before the device is taken into service.

Use

• Connect the LED tube to the mains using the power cable.
• You can link up to 300 LED tubes.

Cleaning and Maintenance

1.  All screws should be tightened and free of corrosion.
2.  The housing, visible parts, mounting supports and the installation location (e.g. ceiling, suspension, trussing) should not be deformed, modified or tampered with e.g. do not drill extra holes in mounting supports, do not change the location of the connections.
3.  Moving mechanic parts must not show any signs of wear and tear.
4.  The electric power supply cables must not show any damage. Have a qualified technician maintain the device.
5.  Disconnect the device from the mains prior to maintenance activities.
6.  Wipe the device regularly with a moist, lint-free cloth. Do not use alcohol or solvents.
7.  There are no user-serviceable parts.
8.  Contact your dealer for spare parts if necessary.

Technical Specifications

• Power Supply max. 230VAC/50Hz
• Power Consumption max. 10W
• Fuse 2A, 250VAC (5 x 20mm) (order code FF2N)
• Colours blue (VDLLTCB), red (VDLLTCR), green (VDLLTCG), yellow (VDLLTCY), RGB (VDLLTCRGB)
• Dimensions 1030 x 50mm
• Total Weight 425g
• Max. Ambient Temperature 45°C
• Max. Housing Temperature 130°C

Use this device with original accessories only. Velleman nv cannot be held responsible in the event of damage or injury resulted from (incorrect) use of this device. For more info concerning this product, please visit our website www.hqpower.eu. The information in this manual is subject to change without prior notice.

References

• Details – Own brands – Velleman – Wholesaler and developer of electronics

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>