velleman VTSS230 Soldering Station and Hot Air Station User Manual

: June 5, 2024
: Velleman

Table of Contents

velleman VTSS230 Soldering Station and Hot Air Station
Introduction
Product Features
Installation
Operation
How to Solder
Setup
Cleaning and Maintenance
Technical Specifications
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

velleman VTSS230 Soldering Station and Hot Air Station

Introduction

To all residents of the European Union
Important environmental information about this product
This symbol on the device or the package indicates that disposal of the device after its lifecycle could harm the environment.
Do not dispose of the unit (or batteries) as unsorted municipal waste; it should be taken to a specialized company for recycling.
This device should be returned to your distributor or to a local recycling service. Respect the local environmental rules.
If in doubt, contact your local waste disposal authorities.
Thank you for choosing Velleman! Please read the manual thoroughly before bringing this device into service.
If the device was damaged in transit, do not install or use it and contact your dealer.

Product Features

Safety Instructions

This device can be used by children aged from 8 years and above, and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the use of the device in a safe way and understand the hazards involved
Children shall not play with the device.
Cleaning and user maintenance shall not be made by children without supervision.
Read and understand this manual and all safety signs before using this appliance.
Indoor use only. Keep this device away from rain, moisture, splashing and dripping liquids.
Never put objects filled with liquids on top of or close to the device.
Always disconnect mains power when the device is not in use or when servicing or maintenance activities are performed. Handle the power cord by the plug only.
After switching off, leave the power cord plugged in for a few minutes.
When you switch off the unit, the automatic cooling function blows cooling air through the heater pipe for a short period.
This protects the heater from damage and extends its lifetime.
Do not disconnect the mains plug during this cooling process.
Do not crimp the power cord and protect it against damage.
If the power cord is damaged, it must be replaced by the manufacturer, its service agent, or similarly qualified persons in order to avoid any hazard.
Make sure that the available voltage does not exceed the voltage stated in the specifications of this manual.
Plug the power cord into a suitable, earthed mains outlet.
Risk of electroshock when opening the cover. Touching live wires can cause life-threatening electroshocks.
Do not disassemble or open the housing yourself.
Have the device repaired by qualified personnel.
Do not operate the device with wet hands.
Never use the device on live electronic circuits.
Make sure power to the work piece is cut and capacitors are discharged.
Do not use near inflammable products or in explosive atmospheres.
Heat can cause fire to inflammable products even when they are not in sight.
Only use in properly ventilated rooms. Incorrect use may cause fire.
Do not touch the shafts, tips, or hot air gun as this can cause serious burns
Keep the tips and hot air away from the body, clothes, or other flammable material.
Do not aim the hot air gun at the eyes.
Use gloves and/or heat-resistant tools to pick up the PCB assembly to prevent burns.
Always return the irons and gun to their stands between uses; always let the device cool down after use and before storage.
Place the device on a level, stable, and fireresistant working surface.

WARNING!

This tool must be placed on its stand when not in use; do not leave the tool unattended when switched on.
Do not inhale solder fumes. The vapors that are released during soldering are harmful.
Therefore, you shall only use the soldering station in well-ventilated areas or under an exhaust hood (solder fume extractor).
Dispose of fume filters and solder residue in accordance with local regulations.
Use the soldering iron on a heatproof workbench.
Place the soldering iron in its holder after use.
Let a hot soldering iron cool down naturally and do not immerse in water.
A fire may result if the appliance is not used with care. Therefore:
be careful when using the appliance in places where there are combustible materials;
do not apply to the same place for a long time;
do not use in presence of an explosive atmosphere;
be aware that heat may be conducted to combustible materials that are out of sight;
place the appliance on its stand after use andallow it to cool down before storage;
do not leave the appliance unattended when it is switched on.

General Guidelines

Refer to the Velleman® Service and Quality Warranty on the last pages of this manual.
All modifications of the device are forbidden for safety reasons. Damage caused by user modifications to the device is not covered by the warranty.
Only use the device for its intended purpose. Using the device in an unauthorised way will void the warranty.
Damage caused by disregard of certain guidelines in this manual is not covered by the warranty and the dealer will not accept responsibility for any ensuing defects or problems.
Nor Velleman Group nv nor its dealers can be held responsible for any damage (extraordinary, incidental or indirect) – of any nature (financial, physical…) arising from the possession, use or failure of this product.
Keep this manual for future reference.

Overview

soldering station display + temperature setting button
airflow control
soldering station on-off switch
soldering station connection
rework station display + temperature setting button
temperature unit setting
rework station on-off switch
rework station connection

Installation

Install the appliance on a flat, stable and fire-resistant surface.
Make sure that the power switch at the back of the appliance is in the off position (0).
Connect the soldering iron to the appliance.
Plug the power cord into a suitable, earthed mains outlet.

Operation

General Operation

To switch on the appliance, set the power switch in the on position (I). The device starts heating up, the temperature and airflow values will be displayed.
Switch on the soldering or rework station with the respective button.
Select the temperature unit with the temperature unit setting switch.
Set the temperature and airflow value with the respective + and – buttons and the airflow control knob.
5. After setting, wait for the values to stabilize before starting to solder.
Please refer to chapter How to Solder below for handy tips.
Do not apply to the same place for a long time.
Do not leave the device unattended when switched on.

Auto Sleep Mode

When the soldering iron is placed in its holder, the switched-on station automatically lowers the iron temperature (sleep mode). As soon as you pick up the iron, the station exits the sleep mode.

Switching Off the Station
After use, place the iron in its holder and switch off the station.After switching off, leave the power cord plugged in for a few minutes. When you switch off the unit, the automatic cooling function blows cooling air through the heater pipe for a short period. This protects the heater from damage and extends its lifetime. Do nodisconnect the mains plug during this cooling process?Wait until the cooling process has stopped, then disconnect the power plug. The deviceuses a small amount of electrical power, even if it is switched off.

How to Solder

Precautions

To extend the life of the heating element in the hot air gun, do not use the device continuously at a low airflow and a high temperature. Allow the heating element to cool after maximum 20 minutes of usage. Place the hot air gun back in its stand when not inuse.
Make sure that both heater and nozzle are cold before attaching the nozzle. High temperatures! Both nozzle and airflow are extremely hot and can cause severe burns.
Never touch the nozzle and heater assembly or allow the hot air to blow against your skin. When used for the first time, the hot air gun may emit some white smoke, but this will soon dissipate.
Always let the unit cool down after use. After switching off, leave the power cord plugged in for a few minutes. When you switch off the unit, the automatic cooling function blows cooling air through the heater pipe for a short period. This protects the heater from damage and extends its lifetime. Do not disconnect the mains plug during this cooling process.

Setup

Do not force the nozzle or pull its edges with pliers.
Make sure the appliance is switched off and the iron/air gun is completely cooled down.
Select the air nozzle and slide it onto the air gun.
Plug in the power cord and switch on the station.
Select the temperature and airflow.
Wait until the temperature is stable.

Cleaning and Maintenance

General
Only perform the maintenance as described in this user manual. Contact an authorised dealer or service agent for any other maintenance or repair. If the iron or station becomes faulty or, for some reason does not operate normally, return it to the service department of your authorized dealer or service agent. Clean the outer cover of the iron and station with a damp cloth and a small amount of liquid detergent. Never submerge the unit in liquid or allow any liquid to enter the case of the station. Never use any solvent to clean the case. Use only original replacement parts

Storing

Store the appliance, its accessories and this user manual in the original packaging. Always store in a cool and dry place.